Chevrolet · 2001-04

Chevrolet Corvette C5 Z06 ECU and tuning guide

The Chevrolet Corvette C5 Z06 (2001-04) runs the LS6: 5.7 L V8, naturally aspirated, port injection, drive-by-wire throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Factory ECU, pinout and chassis research on this page is shared with Chevrolet Corvette C5 Base, Chevrolet Camaro 4th gen Z28 / SS (LS1), Pontiac Firebird / Trans Am 4th gen Formula / Trans Am (LS1).

Chevrolet Corvette C5 Z06, side view
Studio render for illustration, not a photograph of a specific car.

Engine: LS6

Years2001-05
Displacement5.7L
LayoutV8
InductionNaturally aspirated
InjectionPort injection
Cam controlnonepushrod
IgnitionCoil-on-plug
Swap demandHigh

Part of the GM LS (Gen III / IV) family.

Modeled power and torque

Modelled estimate, not a dyno result.

LS6: stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
020040060080002004006008001k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (405 hp at 6000 rpm, 400 lb-ft at 4800 rpm); the curve shape between peaks is modeled. Intake + exhaust + tune (pump fuel): Typical NA gains come mostly above mid-rpm.

LS6 data

Platform background

The C5 Corvette (1997-2004) and the fourth-generation Camaro/Firebird with the LS1 (1998-2002) introduced the Gen III LS. Both use a 24x crank / 1x cam trigger and a single Gen III PCM that runs the engine and the 4L60-E automatic. The C5 was GM's first drive-by-wire Corvette and uses a separate throttle actuator control (TAC) module; the F-body uses a cable throttle. The C5 Z06 added the LS6 from 2001.

Factory ECU

Engine/trigger

LS1 (all) and LS6 (2001-04 Z06): Gen III, 24x crank, 1x cam sensor at rear of block

Sourced863
PCM generations
  • 1997-98 PCM is a different type
  • 1999 is the same type as 2000-on but with some pinout differences
  • The '411' PCM is standard from 2000
Sourced · medium5
PCM connectors
  • 411-type PCM uses red and blue connectors
  • The later '242' truck PCM uses green and blue
Sourced · medium7
Throttle (C5)
  • Drive-by-wire from 1997 via an all-plastic TAC module paired with the PCM over a serial link
  • Throttle body unchanged through C5 production
Sourced · medium7
Throttle (F-body)
  • Cable throttle
  • An F-body PCM is not set up for the C5 TAC serial data
Low confidence45
Transmission control

Gen III PCM controls engine and 4L60-E transmission in a single module

Sourced · medium8
Anti-theftFactory anti-theft link to the PCM must be disabled for swapsSourced · medium5

Use a matched set: a C5 needs a PCM calibrated for drive-by-wire and the matching early TAC module. An F-body runs a cable-throttle calibration with an idle air control valve. The PCM operating system and calibration, not just the hardware, decide which throttle type it supports.

Factory ECU pinout

Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.

GM Gen III LS 24x PCM (2004 Corvette C5 pinout)

The C5 Corvette's Gen III LS1/LS6 powertrain control module (PCM) uses two 80-way connectors, C1 and C2, on a 24x crank trigger with a separate throttle actuator control module. This page transcribes GM's 2004 Corvette PCM connector tables: 160 cavities, each with wire colour, circuit number and function, plus the connector face layout.

2004 (pinout as documented); C5 1997-2004 · US · 2 connectors, 160 cavities · 160 terminals sourced

PCM connector C180 cavities · 80 terminals listed · GM 12191489, 80-Way F Micro-Pack 100W Series Sealed (NAT) with blue (TPA-BLU) terminal position assurance (TPA), as printed in the GM connector part information; centre bolt; two rows of 40 in two 20-cavity blocks.

Looking into the harness plug's mating face (mirror of the ECU face).

How the OEM figure is orientedGM's figure ("PCM Connector Terminal Identification C1/C2") is not labelled harness side or PCM side. It draws the 80-way connector face with two rows of two 20-cavity blocks either side of a centre bolt, latch housings along the top edge, cavity 1 bottom-left, 40 bottom-right, 41 top-left and 80 top-right; on the C2 figure 20/21 and 60/61 are printed either side of the bolt. GM connector end views normally show the harness connector mating face, which is how it is stored here; confirm against the numbers moulded on the connector before wiring.
GM Gen III LS 24x PCM (2004 Corvette C5 pinout): PCM connector C1square key, outer leftsquare key, inner leftcentre bolt (jack screw)square key, inner rightsquare key, outer rightlatch housing, leftlatch housing, centrelatch housing, right1: Ground (circuit 451)12: 12-Volt Reference (circuit 1867)23: Fuel Injector 3 Control (circuit 1746)34: Fuel Injector 2 Control (circuit 1745)45: Not used (per GM table)56: Not used (per GM table)67: 5-Volt Reference (circuit 596)78: Not used (per GM table)89: Not used (per GM table)910: Not used (per GM table)1011: Knock Sensor 2 Signal (circuit 1876)1112: Crankshaft Position (CKP) Sensor Signal (circuit 1869)1213: Requested Torque Signal (circuit 463)1314: Throttle Actuator Control Serial Data (circuit 800)1415: Throttle Actuator Control Serial Data (circuit 1061)1516: Not used (per GM table)1617: Transmission Fluid Pressure Switch Signal B (circuit 1225)1718: Transmission Fluid Pressure Switch Signal C (circuit 1226)1819: Ignition 1 Voltage (circuit 239)1920: Battery Positive Voltage (circuit 340)2021: Low Reference (circuit 1868)2122: Not used (per GM table)2223: Low Reference (circuit 720)2324: Ground (circuit 451)2425: HO2S Low Signal Bank 2 Sensor 2 (circuit 1671)2526: HO2S Low Signal Bank 2 Sensor 1 (circuit 1667)2627: Ground (circuit 451)2728: HO2S Low Signal Bank 1 Sensor 2 (circuit 1669)2829: HO2S Low Signal Bank 1 Sensor 1 (circuit 1653)2930: Not used (per GM table)3031: Not used (per GM table)3132: Transmission Range Switch Signal A (circuit 771)3233: TCC Brake Switch Signal (circuit 420)3334: Transmission Range Switch Signal P (circuit 776)3435: CPP Switch Signal (circuit 48)3536: Fuel Injector 1 Control (circuit 1744)3637: Fuel Injector 6 Control (circuit 846)3738: Damping Lift/Dive Signal (circuit 1101)3839: Not used (per GM table)3940: Ground (circuit 451)4041: Not used (per GM table)4142: Low Speed Cooling Fan Relay Control (circuit 335)4243: Fuel Injector 7 Control (circuit 877)4344: Fuel Injector 4 Control (circuit 844)4445: 5-Volt Reference (circuit 474)4546: 5-Volt Reference (circuit 598)4647: Not used (per GM table)4748: 5-Volt Reference (circuit 416)4849: Not used (per GM table)4950: Not used (per GM table)5051: Knock Sensor 1 Signal (circuit 496)5152: Not used (per GM table)5253: Low Reference (circuit 1057)5354: Low Reference (circuit 469)5455: Not used (per GM table)5556: Not used (per GM table)5657: Battery Positive Voltage (circuit 340)5758: PCM Class 2 Serial Data (circuit 1049)5859: Not used (per GM table)5960: Low Reference (circuit 407)6061: Low Reference (circuit 632)6162: Extended Travel Brake Switch Signal (circuit 847)6263: Low Reference (circuit 452)6364: Ground (circuit 451)6465: HO2S High Signal Bank 2 Sensor 2 (circuit 1670)6566: HO2S High Signal Bank 2 Sensor 1 (circuit 1666)6667: Ground (circuit 451)6768: HO2S High Signal Bank 1 Sensor 2 (circuit 1668)6869: HO2S High Signal Bank 1 Sensor 1 (circuit 1665)6970: Oil Level Switch Signal (circuit 1174)7071: Not used (per GM table)7172: Transmission Range Switch Signal B (circuit 772)7273: Camshaft Position (CMP) Sensor Signal (circuit 633)7374: Engine Coolant Temperature (ECT) Sensor Signal (circuit 410)7475: Not used (per GM table)7576: Fuel Injector 5 Control (circuit 845)7677: Fuel Injector 8 Control (circuit 878)7778: Not used (per GM table)7879: Skip Shift Solenoid Control (manual) or 3-2 Shift Solenoid Valve Control (automatic) (circuits 587 / 687)7980: Low Reference (circuit 718)80
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Ground (circuit 451)chassis/PCM groundBLK/WHT
212-Volt Reference (circuit 1867)12 V sensor supplyLT GRNGM prints only "12-Volt Reference". GM's CKP diagnostic (DTC P0335 family) describes the CKP sensor as 12-volt reference, low reference and signal circuits; the CMP sensor also has a 12-volt reference (C2 pin 39 is the other one in this table). Which reference feeds which sensor is not stated in the table, so confirm with the schematic before wiring.
3Fuel Injector 3 Control (circuit 1746)low-side injector driverPNK/BLK
4Fuel Injector 2 Control (circuit 1745)low-side injector driverLT GRN/BLK
5Not used (per GM table)Other / not used—
6Not used (per GM table)Other / not used—
75-Volt Reference (circuit 596)5 V sensor supplyGRY
8Not used (per GM table)Other / not used—
9Not used (per GM table)Other / not used—
10Not used (per GM table)Other / not used—
11Knock Sensor 2 Signal (circuit 1876)Sensor signalLT BLU
12Crankshaft Position (CKP) Sensor Signal (circuit 1869)Crank / camDK BLU/WHT
13Requested Torque Signal (circuit 463)Comms / diagORN/BLKTorque request link to the separate Throttle Actuator Control (TAC) module; the C5 is drive-by-wire.
14Throttle Actuator Control Serial Data (circuit 800)Comms / diagTANSerial data link to the separate Throttle Actuator Control (TAC) module.
15Throttle Actuator Control Serial Data (circuit 1061)Comms / diagORN/BLKSerial data link to the separate Throttle Actuator Control (TAC) module.
16Not used (per GM table)Other / not used—
17Transmission Fluid Pressure Switch Signal B (circuit 1225)Sensor signalDK BLU
18Transmission Fluid Pressure Switch Signal C (circuit 1226)Sensor signalRED
19Ignition 1 Voltage (circuit 239)ignition-switched 12 V inputPNK
20Battery Positive Voltage (circuit 340)battery positive inputORN
21Low Reference (circuit 1868)sensor low reference (ground)YEL/BLK
22Not used (per GM table)Other / not used—
23Low Reference (circuit 720)sensor low reference (ground)GRY
24Ground (circuit 451)chassis/PCM groundBLK/WHT
25HO2S Low Signal Bank 2 Sensor 2 (circuit 1671)Sensor signalTAN
26HO2S Low Signal Bank 2 Sensor 1 (circuit 1667)Sensor signalTAN
27Ground (circuit 451)chassis/PCM groundBLK/WHT
28HO2S Low Signal Bank 1 Sensor 2 (circuit 1669)Sensor signalTAN/WHT
29HO2S Low Signal Bank 1 Sensor 1 (circuit 1653)Sensor signalTAN/WHT
30Not used (per GM table)Other / not used—
31Not used (per GM table)Other / not used—
32Transmission Range Switch Signal A (circuit 771)Sensor signalBLK/WHT
33TCC Brake Switch Signal (circuit 420)Sensor signalPPL
34Transmission Range Switch Signal P (circuit 776)Sensor signalWHT
35CPP Switch Signal (circuit 48)Sensor signalGRY
36Fuel Injector 1 Control (circuit 1744)low-side injector driverBLK
37Fuel Injector 6 Control (circuit 846)low-side injector driverYEL/BLK
38Damping Lift/Dive Signal (circuit 1101)Other / not usedPNK/WHTLink to the C5 ride-control (damping) system.
39Not used (per GM table)Other / not used—
40Ground (circuit 451)chassis/PCM groundBLK/WHT
41Not used (per GM table)Other / not used—
42Low Speed Cooling Fan Relay Control (circuit 335)OutputsDK GRN
43Fuel Injector 7 Control (circuit 877)low-side injector driverRED/BLK
44Fuel Injector 4 Control (circuit 844)low-side injector driverLT BLU/BLK
455-Volt Reference (circuit 474)5 V sensor supplyGRY
465-Volt Reference (circuit 598)5 V sensor supplyGRY
47Not used (per GM table)Other / not used—
485-Volt Reference (circuit 416)5 V sensor supplyGRY
49Not used (per GM table)Other / not used—
50Not used (per GM table)Other / not used—
51Knock Sensor 1 Signal (circuit 496)Sensor signalDK BLU
52Not used (per GM table)Other / not used—
53Low Reference (circuit 1057)sensor low reference (ground)ORN/BLK
54Low Reference (circuit 469)sensor low reference (ground)ORN/BLK
55Not used (per GM table)Other / not used—
56Not used (per GM table)Other / not used—
57Battery Positive Voltage (circuit 340)battery positive inputORN
58PCM Class 2 Serial Data (circuit 1049)Comms / diagDK GRN
59Not used (per GM table)Other / not used—
60Low Reference (circuit 407)sensor low reference (ground)BLK
61Low Reference (circuit 632)sensor low reference (ground)PNK/BLK
62Extended Travel Brake Switch Signal (circuit 847)Sensor signalGRY
63Low Reference (circuit 452)sensor low reference (ground)BLK
64Ground (circuit 451)chassis/PCM groundBLK/WHT
65HO2S High Signal Bank 2 Sensor 2 (circuit 1670)Sensor signalPPL
66HO2S High Signal Bank 2 Sensor 1 (circuit 1666)Sensor signalPPL
67Ground (circuit 451)chassis/PCM groundBLK/WHT
68HO2S High Signal Bank 1 Sensor 2 (circuit 1668)Sensor signalPPL/WHT
69HO2S High Signal Bank 1 Sensor 1 (circuit 1665)Sensor signalPPL/WHT
70Oil Level Switch Signal (circuit 1174)Sensor signalBRN
71Not used (per GM table)Other / not used—
72Transmission Range Switch Signal B (circuit 772)Sensor signalYEL
73Camshaft Position (CMP) Sensor Signal (circuit 633)Crank / camBRN/WHT
74Engine Coolant Temperature (ECT) Sensor Signal (circuit 410)Sensor signalYEL
75Not used (per GM table)Other / not used—
76Fuel Injector 5 Control (circuit 845)low-side injector driverBLK/WHT
77Fuel Injector 8 Control (circuit 878)low-side injector driverDK BLU/WHT
78Not used (per GM table)Other / not used—
79Skip Shift Solenoid Control (manual) or 3-2 Shift Solenoid Valve Control (automatic) (circuits 587 / 687)OutputsGRY or WHTGM's table lists two entries for this cavity: GRY circuit 587 Skip Shift Solenoid Control and WHT circuit 687 3-2 Shift Solenoid Valve Control. No option code is printed on this row; the skip-shift solenoid belongs to the manual gearbox and the 3-2 shift solenoid valve to the automatic, so only one is populated per car. Check the car's transmission before wiring.
80Low Reference (circuit 718)sensor low reference (ground)BRN

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (medium confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

PCM connector C280 cavities · 80 terminals listed · GM 12191488, 80-Way F Micro-Pack 100W Series Sealed (NAT) with green (TPA-GRN) terminal position assurance (TPA), as printed in the GM connector part information; centre bolt; two rows of 40 in two 20-cavity blocks.

Looking into the harness plug's mating face (mirror of the ECU face).

How the OEM figure is orientedGM's figure ("PCM Connector Terminal Identification C1/C2") is not labelled harness side or PCM side. It draws the 80-way connector face with two rows of two 20-cavity blocks either side of a centre bolt, latch housings along the top edge, cavity 1 bottom-left, 40 bottom-right, 41 top-left and 80 top-right; on the C2 figure 20/21 and 60/61 are printed either side of the bolt. GM connector end views normally show the harness connector mating face, which is how it is stored here; confirm against the numbers moulded on the connector before wiring.
GM Gen III LS 24x PCM (2004 Corvette C5 pinout): PCM connector C2square key, outer leftsquare key, inner leftcentre bolt (jack screw)square key, inner rightsquare key, outer rightlatch housing, leftlatch housing, centrelatch housing, right1: Ground (circuit 451)12: TCC PWM Solenoid Valve Control (circuit 418)23: Not used (per GM table)34: AIR Solenoid Control (circuit 421)45: Delivered Torque Signal (circuit 464)56: PC Solenoid valve High Control (circuit 1228)67: Not used (per GM table)78: PC Solenoid Valve Low Control (circuit 1229)89: Fuel Pump Relay Control (circuit 465)910: Engine Speed Signal (circuit 121)1011: Not used (per GM table)1112: Not used (per GM table)1213: Not used (per GM table)1314: A/C Refrigerant Pressure Sensor Signal (circuit 380)1415: Generator Turn On Signal (circuit 225)1516: Not used (per GM table)1617: A/C Request Signal (C60 only) (circuit 762)1718: A/C Compressor Clutch Supply Voltage (circuit 59)1819: Not used (per GM table)1920: Signal Low - Front (circuit 401)2021: Signal High - Front (circuit 400)2122: Not used (per GM table)2223: Not used (per GM table)2324: Not used (per GM table)2425: IAT Sensor Signal (circuit 472)2526: IC 1 Control (circuit 2121)2627: IC 7 Control (circuit 2127)2728: IC 6 Control (circuit 2126)2829: IC 4 Control (circuit 2124)2930: Not used (per GM table)3031: MAF Sensor Signal (circuit 492)3132: MAP Sensor Signal (circuit 432)3233: High Speed Cooling Fan Relay Control (circuit 473)3334: EVAP Canister Purge Solenoid Control (circuit 428)3435: Not used (per GM table)3536: AIR Pump Relay Control (circuit 436)3637: Not used (per GM table)3738: Not used (per GM table)3839: 12-Volt Reference (circuit 631)3940: Ground (circuit 451)4041: Not used (per GM table)4142: TCC Solenoid Valve Control (circuit 422)4243: A/C Compressor Clutch Relay Control (circuit 459)4344: Reverse Lockout Solenoid Control (circuit 1652)4445: EVAP Canister Vent Solenoid Control (circuit 1310)4546: Malfunction Indicator Lamp (MIL) Control (circuit 419)4647: Skip Shift Indicator Control (MM6) or 2-3 Shift Solenoid Valve Control (M30) (circuits 375 / 1223)4748: 1-2 Shift Solenoid Valve Control (circuit 1222)4849: Not used (per GM table)4950: Vehicle Speed Signal (circuit 817)5051: TFT Sensor Signal (circuit 1227)5152: HO2S Heater Low Control (circuit 2391)5253: HO2S Heater Low Control (circuit 3223)5354: Fuel Level Sensor Signal (circuit 1936)5455: Not used (per GM table)5556: Not used (per GM table)5657: Low Reference (circuit 719)5758: Oil Pressure Sensor Signal (circuit 331)5859: Not used (per GM table)5960: Low Reference (circuit 2129)6061: Low Reference (circuit 2130)6162: Transmission Range Switch Signal C (circuit 773)6263: Transmission Fluid Pressure Switch Signal A (circuit 1224)6364: Fuel Tank Pressure Sensor Signal (circuit 890)6465: Not used (per GM table)6566: IC 8 Control (circuit 2128)6667: IC 2 Control (circuit 2122)6768: IC 5 Control (circuit 2125)6869: IC 3 Control (circuit 2123)6970: Not used (per GM table)7071: Not used (per GM table)7172: HO2S Heater Low Control (circuit 3113)7273: Fuel Level Sensor Signal (Secondary) (circuit 1937)7374: HO2S Heater Low Control (circuit 3212)7475: Generator Field Duty Cycle Signal (circuit 23)7576: Not used (per GM table)7677: Not used (per GM table)7778: Not used (per GM table)7879: Not used (per GM table)7980: Low Reference (circuit 407)80
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Ground (circuit 451)chassis/PCM groundBLK/WHT
2TCC PWM Solenoid Valve Control (circuit 418)OutputsBRN
3Not used (per GM table)Other / not used—
4AIR Solenoid Control (circuit 421)OutputsPPL
5Delivered Torque Signal (circuit 464)Comms / diagTAN/BLKTorque feedback from the separate Throttle Actuator Control (TAC) module.
6PC Solenoid valve High Control (circuit 1228)OutputsRED/BLK
7Not used (per GM table)Other / not used—
8PC Solenoid Valve Low Control (circuit 1229)OutputsLT BLU/WHT
9Fuel Pump Relay Control (circuit 465)OutputsDK GRN/WHT
10Engine Speed Signal (circuit 121)Comms / diagWHT
11Not used (per GM table)Other / not used—
12Not used (per GM table)Other / not used—
13Not used (per GM table)Other / not used—
14A/C Refrigerant Pressure Sensor Signal (circuit 380)Sensor signalRED/BLK
15Generator Turn On Signal (circuit 225)OutputsRED
16Not used (per GM table)Other / not used—
17A/C Request Signal (C60 only) (circuit 762)Sensor signalDK GRN/WHTPrinted "C60 only" (an RPO option code in the GM table).
18A/C Compressor Clutch Supply Voltage (circuit 59)Sensor signalDK GRN
19Not used (per GM table)Other / not used—
20Signal Low - Front (circuit 401)Sensor signalPPLPrinted exactly as "Signal Low - Front"; the GM table does not name the sensor on circuits 400/401.
21Signal High - Front (circuit 400)Sensor signalYELPrinted exactly as "Signal High - Front"; the GM table does not name the sensor on circuits 400/401.
22Not used (per GM table)Other / not used—
23Not used (per GM table)Other / not used—
24Not used (per GM table)Other / not used—
25IAT Sensor Signal (circuit 472)Sensor signalTAN
26IC 1 Control (circuit 2121)ignition control output to coil (IC)PPL
27IC 7 Control (circuit 2127)ignition control output to coil (IC)RED
28IC 6 Control (circuit 2126)ignition control output to coil (IC)LT BLU/WHT
29IC 4 Control (circuit 2124)ignition control output to coil (IC)DK GRN/WHT
30Not used (per GM table)Other / not used—
31MAF Sensor Signal (circuit 492)Sensor signalYEL
32MAP Sensor Signal (circuit 432)Sensor signalLT GRN
33High Speed Cooling Fan Relay Control (circuit 473)OutputsDK BLU
34EVAP Canister Purge Solenoid Control (circuit 428)OutputsDK GRN/WHT
35Not used (per GM table)Other / not used—
36AIR Pump Relay Control (circuit 436)OutputsBRN
37Not used (per GM table)Other / not used—
38Not used (per GM table)Other / not used—
3912-Volt Reference (circuit 631)12 V sensor supplyRED
40Ground (circuit 451)chassis/PCM groundBLK/WHT
41Not used (per GM table)Other / not used—
42TCC Solenoid Valve Control (circuit 422)OutputsTAN/BLK
43A/C Compressor Clutch Relay Control (circuit 459)OutputsDK GRN/WHT
44Reverse Lockout Solenoid Control (circuit 1652)OutputsLT GRN
45EVAP Canister Vent Solenoid Control (circuit 1310)OutputsWHT
46Malfunction Indicator Lamp (MIL) Control (circuit 419)OutputsBRN/WHT
47Skip Shift Indicator Control (MM6) or 2-3 Shift Solenoid Valve Control (M30) (circuits 375 / 1223)OutputsWHT or YEL/BLKGM's table lists two entries: WHT circuit 375 Skip Shift Indicator Control (MM6, manual) and YEL/BLK circuit 1223 2-3 Shift Solenoid Valve Control (M30, automatic).
481-2 Shift Solenoid Valve Control (circuit 1222)OutputsLT GRN
49Not used (per GM table)Other / not used—
50Vehicle Speed Signal (circuit 817)Other / not usedDK GRN/WHT
51TFT Sensor Signal (circuit 1227)Sensor signalYEL/BLK
52HO2S Heater Low Control (circuit 2391)HO2S heater low-side controlBRN
53HO2S Heater Low Control (circuit 3223)HO2S heater low-side controlRED/WHT
54Fuel Level Sensor Signal (circuit 1936)Sensor signalDK BLU
55Not used (per GM table)Other / not used—
56Not used (per GM table)Other / not used—
57Low Reference (circuit 719)sensor low reference (ground)PPL
58Oil Pressure Sensor Signal (circuit 331)Sensor signalTAN/WHT
59Not used (per GM table)Other / not used—
60Low Reference (circuit 2129)sensor low reference (ground)BRN
61Low Reference (circuit 2130)sensor low reference (ground)BRN/WHT
62Transmission Range Switch Signal C (circuit 773)Sensor signalGRY
63Transmission Fluid Pressure Switch Signal A (circuit 1224)Sensor signalPNK
64Fuel Tank Pressure Sensor Signal (circuit 890)Sensor signalDK GRN
65Not used (per GM table)Other / not used—
66IC 8 Control (circuit 2128)ignition control output to coil (IC)PPL/WHT
67IC 2 Control (circuit 2122)ignition control output to coil (IC)RED/WHT
68IC 5 Control (circuit 2125)ignition control output to coil (IC)DK GRN
69IC 3 Control (circuit 2123)ignition control output to coil (IC)LT BLU
70Not used (per GM table)Other / not used—
71Not used (per GM table)Other / not used—
72HO2S Heater Low Control (circuit 3113)HO2S heater low-side controlBLK/WHT
73Fuel Level Sensor Signal (Secondary) (circuit 1937)Sensor signalLT BLU
74HO2S Heater Low Control (circuit 3212)HO2S heater low-side controlLT GRN
75Generator Field Duty Cycle Signal (circuit 23)Sensor signalGRY
76Not used (per GM table)Other / not used—
77Not used (per GM table)Other / not used—
78Not used (per GM table)Other / not used—
79Not used (per GM table)Other / not used—
80Low Reference (circuit 407)sensor low reference (ground)BLK

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (medium confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

Scope: every pin row is the 2004 model-year Corvette table (Engine Controls, 5.7L). Tables for 1997-2003 C5 cars were not checked for this file, so on those cars compare each wire colour and circuit number at the connector before cutting anything.

Corvette only. The 1998-2002 Camaro and Firebird LS1 (cable throttle, no TAC module) and the Gen III trucks also use 24x LS PCMs, but their GM connector tables were not available from an allowed source for this file and were not compared. Do not assume the Corvette pin functions carry over; the Camaro, Firebird, truck, Monaro and GTO catalog rows are deliberately not linked here.

The C5 is drive-by-wire: the PCM talks to a separate Throttle Actuator Control (TAC) module over C1 pins 13-15 and C2 pin 5. The TAC module connectors are not covered here. GM's table prints connector C1 with a blue TPA and C2 with a green TPA for this model year.

The common hardware names P01 and P59 (and the 24x / 58x split between Gen III and Gen IV) are enthusiast shorthand; they are not printed in the GM tables used here, and no PCM service part numbers were sourced, so none are listed.

Safety: disconnect the battery before unplugging the PCM, release the centre bolt rather than prying the connectors, and do not back-probe through the sealed connector rear with sharp probes; probe from the mating face with a proper terminal test adapter. Two cavities (C1 79 and C2 47) carry different circuits on manual and automatic cars.

All factory ECU pinouts →

Harness: wire-in

Route for this carWire-in
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

No plug-and-play harness for the S3 pinout is listed for this vehicle yet. The route is a universal wire-in harness: the factory ECU is removed and each circuit is wired to the new ECU from a pinout. Nothing is written to the factory ECU.

Plug-and-play

Being researched

We're mapping S3 plug-in and factory-connector adapter harnesses to this application.

Wire-in

Universal flying lead or re-terminated factory harness

Always available: terminate the engine side to ECU2's two Superseal 34 connectors. Universal harness from $405 USD list.

Your GAINS system for this car · pre-release

ECU2 for the Corvette C5

Planned with the same rules as the configurator for this car's 8 cyl · port injection · cable or drive-by-wire. The factory ECU is unplugged and replaced; nothing is written to it.

Chevrolet Corvette C5 Z06 studio render
Corvette C5
  • ECU2Engine controller

    8 cyl · port injection · cable or drive-by-wire

    Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • Drive-by-wire built inFour half-bridges run up to two electronic throttles, with pedal and throttle sensors on the ECU's own inputs and a windowed watchdog that cuts the motors in hardware on a fault.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harnessNone listed for this car
  2. Factory-connector → S3 adapterNone listed for this car
  3. Wire-inYour route: universal wire-in harness

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Corvette C5

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  4. 4
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAF+MAP (blended / torque model) (low confidence)

  5. 5
    Wideband sensorhardware

    factory O2 type not yet sourced; plan on a Bosch LSU 4.9 for the GAINS ECU's built-in controller

  6. 6
    Bottom end and head sealingfactory reference

    Reported: Same as LS1: stock powder-metal rods and hypereutectic pistons are cited as the first limits under boost. The LS6 block is regarded as stronger at the main webs. (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Drivetrain

C5 layout
  • Front engine with torque tube to a rear-mounted transaxle
  • Near 50/50 weight distribution
Sourced · medium91
C5 transmissions

4L60-E four-speed automatic or Borg-Warner T-56 six-speed manual, rear-mounted

Sourced · medium91

Because the C5 automatic bolts to the rear differential housing, the PCM's transmission calibration is specific to the transaxle. Do not assume an F-body 4L60-E calibration carries over.

Chassis integration

Serial dataTAC module and PCM communicate over a dedicated serial link (C5)Low confidence74

When fitting a standalone controller, budget for the cluster, ABS/traction and A/C, which depend on PCM messages. Retaining the factory PCM is usually simpler on street cars.

Tuning notes

Rev limits
ItemSpeed
LS16,000 rpm
LS66,500 rpm
Sourced3
Injectors
LS13.3 g/s
LS63.6 g/s maximum deliveryGM
Sourced3
Power ratings
  • LS1 rose from 345 to 350 hp for 2001
  • LS6 385 hp at launch in 2001
Sourced3
Knock sensorsValley-mounted Gen III sensors are prone to water damageSourced · medium6

Most modified LS1/LS6 cars hit injector and MAF limits after cam, heads and headers. Start by checking injector duty and MAF frequency against the calibration's maximum, then tune VE and MAF together and confirm spark with knock logging. For a 58x Gen IV engine in these chassis, the usual route is a Gen III PCM plus a 58x-to-24x conversion module.

Popular swaps

Gen IV engine into C5/F-body
  • Keep the Gen III PCM and add a 58x-to-24x conversion module
  • The reverse is not possible without changing the reluctor
Sourced62

Other Corvette C5 guides

GAINS on the Corvette C5

ECU2

ECU2Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

What PCM does a C5 Corvette use?

A Gen III PCM: 1997-98 cars have an early type, 1999 is close to the later type, and 2000-on cars use the common '411' PCM with red and blue connectors, paired with a separate TAC module for drive-by-wire.57

Is the LS1 Camaro drive-by-wire?

No. 1998-2002 F-body LS1 cars use a cable throttle, while the C5 Corvette is drive-by-wire through a TAC module.47

Can I put an LS3 in a C5 Corvette?

Yes. A common approach keeps the 24x Gen III PCM and adds a 58x-to-24x conversion module to read the LS3's 58x crank and 4x cam signals.62

What is the redline of the LS6?

GM set the LS6 redline at 6,500 rpm, versus 6,000 rpm for the LS1.3

What transmission is in a C5 Corvette?

A rear-mounted transaxle: the 4L60-E automatic or the Borg-Warner T-56 six-speed manual, joined to the engine by a torque tube.91

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. The Complete C5 Corvette Buyer's Guide · AutoGuide · press · retrieved 2026-10-25
  2. Crank and Cam Timing Sensors: Reluctor Ring Selection for LS, LT, and Coyote Swaps · Billy's Speed Shop · vendor-doc · retrieved 2026-10-25
  3. GM Press Release: 2001 Corvette Performance · General Motors (via Corvette Action Center) · oem · retrieved 2026-10-25
  4. C5 PCM question (forum thread) · CorvetteForum · community · retrieved 2026-10-25
  5. LS Engine Controllers, Making Your LS-Power Change A Controlled Swap · Chevy Hardcore · press · retrieved 2026-10-25
  6. Dialing In LS Sensors For Various Generations With Michigan Motorsports · EngineLabs · press · retrieved 2026-10-25
  7. Navigating Gen-III LS Drive-By-Wire Throttle Bodies With PSI · LSX Magazine · press · retrieved 2026-10-25
  8. 24x vs 58x Reluctor Differences for LS and LT · PSI Conversion · vendor-doc · retrieved 2026-10-25
  9. Chevrolet Corvette (C5) · Wikipedia · community · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  • Factory ECU part numbers not yet sourced for this vehicle.
  1. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  2. E-941 S3 engine harness availability (inferred, medium confidence)