Jeep Cherokee XJ LS Swap (1984-2001): Unibody Mounts, Low-Hood Intake, AW4 Replacement, NP231/NP242 Adapters, Fuel and Legal Guide

A Jeep XJ LS swap is an established conversion with a bolt-and-weld mount kit, headers, radiator and fuel parts from Novak. The hurdles are the low hood, which calls for a car-style intake and accessories, the AW4 automatic, which cannot be adapted, and the oil pan and exhaust fighting the Dana 30 and front driveshaft in a narrow unibody.2411

Difficulty4/5 · Hard2411
  • The XJ is a unibody; the mounts unbolt the factory brackets, need a tapped body insert and are best welded along the top lip.
  • The hood is low: tall truck intakes and accessories will not fit, so a car-style intake and front drive are needed.
  • The AW4 has no GM adapter, so automatic XJs need a GM transmission and transfer case adapter.
  • Oil pan, A/C compressor and exhaust all compete for space with the Dana 30, unibody rails and front driveshaft.

At a glance

The key numbers and parts, with the source on each tile.

Stock engines
  • 2.5 L four, 2.8 L GM V6 (1984-86), 4.0 L six
  • Jeep rated the 1991-on 4.0 L at 190 hp (193 hp for 2000-01)
Sourced · medium19
Curb weight and wheelbase
  • About 3,357 lb1,523 kg
  • 101.4 in wheelbase2,576 mm
Sourced · medium19
Mount kit

Novak MMXJ3 (Gen III/IV LS) or MMXJ5 (Gen V LT), listed for all 1984-2001 XJ and MJ

Sourced2
Intake and accessories

Car-style low intake and Corvette-style front drive for hood, steering gear and fan clearance

Sourced217
Transmission
  • AW4 cannot be adapted
  • 4L60E with Novak 4L61 kit to NP231/NP242
  • AX15 manual via Novak GMAX15
Sourced111210
Oil pan
  • Truck-style LS pan with higher front sump
  • Car pans can hit the front axle on compression
Sourced4
Cooling

Novak KryoFlow HD aluminum radiator for 1987-2001 XJ with integrated shroud and GM-side necks

Sourced8
Fuel

1997-2001 XJ: Novak FSK-9704 raises the about 40 psi (2.8 bar) module output to about 58 psi (4.0 bar)

Sourced6
Speedometer

NP231 and NP242 use a cable drive through 1991 and an electronic speed sensor from 1992

Sourced1314

Recommended engines

  • LS1 · Novak favors the car-version Gen III for the low XJ hood; the aluminum LS1 is listed at about 407 lb (185 kg) against about 515 lb (234 kg) for the Jeep 4.0 L six.
  • 5.3 LM7 / L59 / LY5 (Gen III/IV truck) · Cheap and plentiful; the MotoIQ XJ build uses a Suburban-sourced Gen III, but a truck 5.3 L needs a low car intake and car accessories to clear the hood.
  • LS6 · Car-version Gen III with a low-profile intake and the same 24x crank trigger and accessory layout as the LS1, so it fits the same XJ mount, header and hood plan.

Mounts

A Jeep XJ LS swap starts with mounts made for the unibody.

Novak MMXJ3 / MMXJ5
  • Frame bracket weldments, engine plates, upper and lower HNBR isolators, hardware and instructions
  • 3/16 in steel, 5/8 in through bolts4.8 mm · 16 mm
Sourced2
FitmentAll 1984-2001 XJ Cherokee, XJ Wagoneer and MJ ComancheSourced2
Rear mount
  • Novak RMU urethane mount for automatics, RMAX15 for the AX15
  • Redrilling the factory crossmember is acceptable
Sourced4

Novak's MMXJ3 kit for Gen III and IV engines (MMXJ5 for Gen V LT) replaces the factory brackets with steel weldments, engine plates and HNBR isolators, and is listed for every 1984-2001 XJ and MJ.21

The factory brackets unbolt, and the installer taps a blank body insert to 7/16-14. Novak recommends welding the top lip of the new brackets, and the sides for maximum strength. Its mount geometry fixes the engine position, so do not shift the engine to reuse old driveshafts.24

At the rear, Novak uses its RMU urethane mount for automatics or RMAX15 for the AX15, and says redrilling the factory crossmember is fine. Safety: support the engine on a hoist and the Jeep on stands, and protect fuel and brake lines from weld heat.4

Transmission

Automatic XJs lose the AW4.

AW4
  • Electronically controlled, works only with the 4.0 L and its computer
  • Novak offers no conversion to V6 or V8 power
Sourced11
Novak 4L61-23
  • 4L60E, 4L65E or 4L70E to 23-spline NP207, NP231 or NP242
  • 3.0 in long, 25.5 in combined76 mm · 648 mm
Sourced12
AX15

Novak GMAX15 adapter, 1 in (25 mm) thick, 17.7 in (450 mm) adapted length, GM bellhousing and clutch

Sourced10

Novak calls it electronically controlled and tied to the 4.0 L computer, and says it offers no adapter to a V6 or V8. Plan on a GM 4L60E, which Novak features for Gen III swaps.114

Novak's 4L61 kit joins the 4L60E family to 23-spline NP231 and NP242 cases. Some 1987-1990 NP242s have 21-spline inputs, and Novak recommends swapping in a 23-spline gear. On car-version 4L60Es, fit the truck-style range switch to keep park, neutral and reverse-light functions.124

Novak calls the AX15 the only factory XJ manual worth keeping, for mild engines, using its GMAX15 kit with a GM bellhousing. Its NV3550 kit 3504G is listed for TJ, LJ and CJ7, not the 2000-2001 XJ, so confirm XJ fit with the maker. Novak advises against a 4L80E because its case flange hits the XJ headers.410916

Driveshaft lengths change because the GM engine sits about 3 in (76 mm) farther forward than the Jeep six. Measure after the drivetrain is in and the Jeep sits on its springs. Novak recommends fixed-yoke shafts where possible, and NP231 and NP242 slip-yoke eliminator kits exist.1041514

Clearance

The XJ hood is low.

Hood
  • Stock truck intakes and accessory brackets do not clear
  • Vortec engines need Corvette-style intake and accessories
Sourced2
Oil pan
  • Use a Vortec truck-style pan (higher front sump, deeper rear) and its pickup and dipstick
  • Camaro, Corvette and GTO pans can hit the axle
Sourced4
A/C compressor
  • The Gen III passenger-side compressor hits the unibody
  • Relocate it, for example with a GM R4 or Sanden-style kit
Sourced4

Novak says truck intakes and accessory brackets will not clear it, so Vortec engines need a low car-style intake and Corvette-style front accessories, which also clear the power steering gear and fan. Swapping intakes requires calibration changes.217

Use a Vortec truck oil pan with its pickup, dipstick and tube. Its higher front sump clears the Dana 30, while Camaro, Corvette and GTO pans can hit the axle as the springs compress. With sagged springs, Novak says a lift kit and bump stops may be needed.42

The passenger-side Gen III A/C compressor hits the unibody and must move; Novak suggests a GM R4 with a relocation kit or a Sanden-style kit. A 2-3 in (51-76 mm) lift helps placement, and bump stops keep the front driveshaft off the driver's-side exhaust.4

The steering gear stays factory, and Novak's mounts are shaped to clear the steering shaft and its pillow block. Use the GM pump; a hydraulic shop may need to match the high-pressure hose ends to the Jeep gear.24

Cooling

Novak says the factory XJ radiator suits neither the capacity nor the outlet placement of a GM V8.

Novak KryoFlow HD

Aluminum dual-pass crossflow core for 1987-2001 XJ/MJ, 1-1/2 in (38 mm) passenger-side inlet, 1-3/8 in (35 mm) outlet, integrated shroud

Sourced8
Fan

Novak FX3400-X triple electric fan kit, fits only the Novak radiator

Sourced8
1984-1986 XJ

Needs a later grille support and front structure from a salvage Cherokee to fit this radiator

Sourced8

Its KryoFlow HD radiator for 1987-2001 XJs has GM-side necks, a built-in shroud and bungs for sensors and a steam vent line. Novak advises a cap of no more than 16 psi (1.1 bar).48

On 1984-1996 Cherokees with a remote pressure bottle, the Novak radiator moves the filler neck into the upper hose. Early 1984-1986 XJs need a later grille support and front structure first, because Jeep changed the front clip for the 4.0 L in 1987.84

Route the steam vent line to a radiator bung, and plan a separate transmission cooler for an automatic, as Novak does on its other Jeep radiators. The MotoIQ build notes the stock upper hose is hard to protect in the narrow nose.Medium8718

Fuel

Fuel depends on year.

1997-2001 XJ module
  • Regulates about 40 psi2.8 bar
  • Novak FSK-9704 supplies about 58 psi through a returnless line4.0 bar
Sourced6
Pump

Novak says stock 1987-on XJ in-tank pumps produce about 90 psi (6.2 bar) and need regulation

Sourced4
Rail regulator

FSK-9704NR omits the regulator for engines with one on the rail, typical of many 1997-2002 LS and Vortec engines

Sourced6

For 1997-2001 XJs, Novak's FSK-9704 kit modifies the in-tank module, which regulates about 40 psi (2.8 bar), to feed about 58 psi (4.0 bar) to a GM rail through a returnless line. Pick the NR version if your rail already has a regulator.6

Novak says stock 1987-on XJ in-tank pumps can make about 90 psi (6.2 bar), so any multipoint setup needs the right regulator. We did not find a maker kit for 1987-1996 XJs, so confirm the regulator layout and set pressure with a gauge on the rail.Medium46

Exhaust

Novak's LSXJ3 headers are short and block-hugging, with the passenger side swept back to clear the unibody and firewall.

Novak LSXJ3 headers
  • 1-1/2 in primaries, 2-1/2 in three-bolt collector, passenger side swept back to clear the unibody and firewall38 mm · 64 mm
  • No CARB executive order
Sourced16
4L80E caution
  • The 4L80E case flange interferes with the Novak XJ headers
  • Novak suggests a 4L60
Sourced16
Pipe

Novak suggests a Y-pipe with 2-1/2 in (64 mm) pipe, 3 in (76 mm) as an option, with one oxygen sensor bung per bank

Sourced4

They route under the pan, under the bellhousing slope or behind the transfer case. Novak states they carry no CARB executive order.16

Weld one oxygen sensor bung into each downpipe and keep the factory heat shields over the converter and muffler. Novak warns some jurisdictions may not accept converters this far from the headers, and California needs headers covered by a CARB executive order.416

Watch the driver's side: Novak notes the front driveshaft can contact the exhaust at full compression, which bump stops prevent. Check starter and steering clearance before final welding.Medium4

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

The GM harness mostly runs between the engine and the GM computer, and the Jeep power distribution center can stay.

Diagnostic port

Novak says the 1996-on XJ OBD-II connector works with a GM computer

Sourced4
Cluster

The 1996 XJ electronic cluster is multiplexed and needs Jeep computer signals, or a GM-compatible aftermarket cluster

Sourced4
Tach emulator
  • Novak E-TX fits 1997-2004 XJ and TJ with the 4.0 L and 1997-2002 with the 2.5 L
  • E-TXCC adds cruise for Gen III swaps
Sourced5

Novak says the 1996-on XJ diagnostic port works with the GM computer, and the GM alternator wires up as it did in the donor.4

The 1996-on XJ cluster is multiplexed and needs signals from the Jeep computer. Novak gives two routes: a GM-compatible aftermarket cluster fed by the factory fuel sender, or the Jeep computer running alongside the GM one with an E-TX tach emulator.45

The Jeep speedometer reads the transfer case. NP231 and NP242 cases used a cable drive through 1991 and an electronic three-wire sensor from 1992. The GM computer needs its own speed input; PSI notes LS computers expect a 128k pulse signal and sells converters.131421

Some XJs have ABS, listed with certain rear axles. We found no swap-specific notes on XJ ABS or on any XJ immobilizer, so keep the ABS wiring intact and check your build year before assuming either. Safety: disconnect the battery and fuse each new feed.Low19

Chassis

Engine weights (Novak XJ guide)
  • 4.0 L six 515 lb234 kg
  • GM Gen III 525 lb238 kg
  • LS1 407 lb185 kg
Novak's TJ guide lists an iron Gen III at 470 lb (213 kg); the two pages differSourced · medium4
Axles
  • Dana 30 front
  • Dana 35 or Chrysler 8.25 in rear by year, Dana 44 on some 1987-91 tow packages
Sourced · medium19
NP242 rating
  • New Venture lists 1,486 lb-ft2,015 N·m
  • Output shafts are the weak point
Sourced14

An aluminum LS weighs less than the Jeep 4.0 L six, while an iron truck block weighs about the same or more, and Novak's two guides give different figures for iron Gen III blocks. Novak says to use a front spring rated for the six when replacing one.Medium43

Rear axles vary by year

Dana 35, Chrysler 8.25 in from 1991, and Dana 44 on some tow packages. Novak considers factory Dana 30, 35 and 44 axles able to handle V8 power but leaves upgrades to the builder.Medium194

Both factory transfer cases hold V8 torque in Novak's view. The NP231 is rated far above engine torque, and the NP242 is rated at 1,486 lb-ft (2,015 N·m), limited mainly by its output shafts.Medium13144

Tuning

Computer pairing

Novak recommends a GM computer of the same model year as the engine

Sourced17
Break-in

GM says to avoid maximum engine speed and long high-load periods for the first 500 miles (12 to 15 engine hours)

Sourced22

Calibrate the GM computer for the Jeep

Injectors, transmission, speed input and the intake change. Novak notes swapping a truck intake for a car intake needs calibration work, and that modern GM computers can be reprogrammed by dealers or tuning shops.Medium174

Set shift points and converter lockup for tire size and axle ratio after confirming the speed signal. Gen IV truck engines with Active Fuel Management need it disabled in calibration or hardware.Medium2120

Log with a wideband oxygen sensor, confirm knock control, and make ignition changes in small steps while watching for knock. Follow GM's break-in guidance for a new engine.Medium22

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 23 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

9 stages, in the order most builds follow.

  1. Confirm the year details and the law
    Note the XJ year, transfer case, axle and fuel system, and confirm what your state or country needs before buying parts.
  2. Buy the donor and the low-hood parts
    Get the engine with its harness, computer, pedal and sensors, plus a car-style intake, front accessories and a truck oil pan.
  3. Strip and inspect the unibody
    Remove the old powertrain, repair rust at the mount and crossmember areas, and unbolt the factory mount brackets.
  4. Fit mounts and the drivetrain
    Install the mounts, tap the body insert, set the engine and transmission, and weld the bracket lips.
  5. Check clearance at full compression
    Cycle the front suspension to check pan-to-axle and driveshaft-to-exhaust clearance, and add bump stops or lift as needed.
  6. Order driveshafts
    Measure both driveshafts with the Jeep on its springs and order them, with an SYE kit if the rear shaft is short.
  7. Install cooling, fuel and exhaust
    Fit the radiator, fans, steam line, fuel upgrade and headers, then leak-check fuel with the key on.
  8. Wire the engine and gauges
    Connect the GM computer, speed signals, tach emulator or aftermarket cluster, and fused feeds.
  9. Calibrate, log and road test
    Load a calibration for the Jeep, log with a wideband, check shifting and speedometer, then complete break-in and inspections.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Hood will not close or the fan hits the accessoriesTruck Vortec intakes and accessory brackets are too tall for the low XJ hood.Fit a low car-style intake and Corvette-style accessories, and recalibrate for the intake change.217
Automatic XJ has no adapter for the AW4The AW4 is electronically controlled by the 4.0 L computer, and Novak offers no V8 conversion.Replace it with a GM 4L60E and a transfer case adapter.1112
Oil pan hits the Dana 30 on compressionCar-style pans have a lower front section, and tired factory springs let the axle rise further.Use a Vortec truck pan with its pickup and dipstick, and add bump stops or a mild lift.42
A/C compressor hits the unibodyThe Gen III passenger-side compressor position does not fit the narrow XJ frame rails.Relocate the compressor with a GM R4 relocation kit or a Sanden-style kit.4
Transfer case will not mate to the adapterSome 1987-1990 NP242s have 21-spline inputs, while the Novak 4L60E adapter is 23-spline only.Fit a 23-spline input gear in the transfer case.12
4L80E case fouls the headersThe 4L80E's extended case flange interferes with the Novak XJ header flange.Use a 4L60E-family transmission instead.16

Frequently asked

Is there an LS swap kit for the Jeep XJ?

Yes, as a set of parts rather than one box. Novak sells MMXJ3 mounts for all 1984-2001 XJs, LSXJ3 headers, a KryoFlow HD radiator, a fuel kit for 1997-2001 XJs and transfer case adapters. You still need a low car-style intake, Corvette-style accessories and a truck oil pan from GM donors.21686

Can you keep the AW4 with an LS swap?

No. Novak describes the AW4 as electronically controlled and tied to the 4.0 L engine computer, and it offers no adapter to a V6 or V8. Most automatic XJ swaps use a GM 4L60E with Novak's 4L61 adapter to the NP231 or NP242 transfer case.1112

What oil pan do you need for an XJ LS swap?

Use a Vortec truck-style pan with its matching pickup, dipstick and tube. Its higher front sump clears the Dana 30, while Camaro, Corvette and GTO pans can hit the axle as the springs compress. Check clearance at full compression and add bump stops or a mild lift if the springs have sagged.42

Will the XJ gauges work after an LS swap?

Not without help on 1996-on XJs. Their cluster is multiplexed from the Jeep computer, so either keep that computer running with a tach emulator or fit a GM-compatible aftermarket cluster. The speedometer reads the transfer case sensor, electronic from 1992, and the GM computer needs its own speed signal.4513

Does an XJ need a lift for an LS swap?

Not strictly, but Novak says a 2-3 in (51-76 mm) lift improves engine placement. With sagged factory springs, a lift and bump stops may be needed to keep the oil pan off the Dana 30 and the front driveshaft off the exhaust. Use a front spring rated for the six.42

Is an LS swapped XJ smog legal?

It can be, but it takes planning. In the US the engine generally must be the same model year or newer with its full emissions system, and California requires a BAR Referee inspection and headers covered by a CARB executive order. Novak's XJ headers carry no CARB executive order. Other countries require registration updates or engineering approval.Medium2324164

Related

Sources

28 sources
  1. Engine Mounts: Jeep engine mount catalog (MMX series) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  2. GM LS engine mounts for XJ Cherokee and MJ Comanche (MMXJ3 / MMXJ5) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  3. Guide to GM engine swaps in the Jeep TJ and LJ · Novak Conversions · vendor-doc · retrieved 2026-10-27
  4. Guide to GM V8 swaps in the XJ Cherokee and MJ Comanche · Novak Conversions · vendor-doc · retrieved 2026-10-27
  5. TJ/XJ/JK crank position tach emulator (E-TX / E-TXCC) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  6. Gen III+ fuel system integration kit for TJ and XJ (FSK-9704) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  7. JK radiator for GM Gen III+ conversions (K-JK30H) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  8. XJ/MJ KryoFlow HD radiators (GM Gen III-IV version) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  9. GM engine to Jeep NV3550 adapter (kit 3504G) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  10. GM engine to Jeep AX15 adapter (GMAX15) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  11. AW4 automatic transmission · Novak Conversions · vendor-doc · retrieved 2026-10-27
  12. GM 4L60E/4L65E/4L70E to Jeep NP transfer case adapter (4L61-23) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  13. NP231 transfer case · Novak Conversions · vendor-doc · retrieved 2026-10-27
  14. NP242 transfer case · Novak Conversions · vendor-doc · retrieved 2026-10-27
  15. Driveshafts for Jeep conversions · Novak Conversions · vendor-doc · retrieved 2026-10-27
  16. GM Gen III/IV LS/Vortec headers for XJ/MJ (LSXJ3) · Novak Conversions · vendor-doc · retrieved 2026-10-27
  17. GM Generation III+ V8 engines · Novak Conversions · vendor-doc · retrieved 2026-10-27
  18. Jeep LS Swap Part 1: Introduction · MotoIQ · press · retrieved 2026-10-27
  19. Jeep Cherokee (XJ) · Wikipedia · reference · retrieved 2026-10-27
  20. General Motors LS-based small-block engine · Wikipedia · reference · retrieved 2026-10-27
  21. 4WD LS & LT Swap Compatibility Guide · PSI Conversion · vendor-doc · retrieved 2026-10-27
  22. LS3 EFI Crate Engine Specifications and Installation Instructions (19419889) · Chevrolet Performance (hosted by Speedway Motors) · oem · retrieved 2026-10-27
  23. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  24. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-27
  25. Executive Order D-126-32: GM LS3 E-ROD engine kit · California Air Resources Board · standard · retrieved 2026-10-25
  26. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-25
  27. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  28. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25