Chevrolet / GMC · 2007-13

Chevrolet / GMC Silverado / Sierra / Tahoe / Yukon GMT900 5.3 (LY5 / LMG / LC9) ECU and tuning guide

The Chevrolet / GMC Silverado / Sierra / Tahoe / Yukon GMT900 5.3 (LY5 / LMG / LC9) (2007-13) runs the 5.3 LM7 / L59 / LY5 (Gen III/IV truck): 5.3 L V8, naturally aspirated, port injection, drive-by-wire throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Factory ECU, pinout and chassis research on this page is shared with Chevrolet / GMC Silverado / Sierra / Tahoe / Yukon GMT800 4.8 / 5.3, Chevrolet / GMC Silverado / Sierra / Tahoe / Yukon GMT800 / GMT900 6.0 (LQ4 / LQ9 / LY6).

Chevrolet / GMC Silverado / Sierra / Tahoe / Yukon GMT900 5.3 (LY5 / LMG / LC9), side view
Studio render for illustration, not a photograph of a specific car.
Years1999-13
Displacement5.3L
LayoutV8
InductionNaturally aspirated
InjectionPort injection
Cam control
  • None
  • AFM on later Gen IV
IgnitionCoil-on-plug
Swap demandHigh

Part of the GM LS (Gen III / IV) family. AFM on later engines

Modeled power and torque

Modelled estimate, not a dyno result.

Dyno model not available yet for the 5.3 LM7 / L59 / LY5 (Gen III/IV truck). Stock-anchored curves are added as factory ratings are sourced.

5.3 LM7 / L59 / LY5 (Gen III/IV truck) data

Platform background

GM's full-size trucks and SUVs are the main source of junkyard LS engines. GMT800 trucks (1999-2007 Classic) use Gen III 24x iron-block 4.8/5.3/6.0 engines (LR4, LM7, LQ4, LQ9) with P01/P59-family PCMs. GMT900 trucks (2007-2013/14) use Gen IV 58x engines (LY5, LC9, LMG, LH6, LY6, L92 family) with the CAN-based E38 ECM, a separate TCM for the 6L80/6L90, and, on many engines, AFM and cam phasing.

Factory ECU

GMT800 engines

LR4 4.8, LM7 5.3, LQ4/LQ9 6.0: iron block, cathedral-port heads, 24x reluctor

Sourced · medium1079
GMT800 PCM
  • Gen III P01/P59-family PCMs
  • The common '0411' unit is a popular swap PCM. Later 2003-07 drive-by-wire trucks use the '242' PCM with a metal-bracket TAC module
Sourced · medium185
GMT900 engines
  • LY5/LC9/LMG/LH6 5.3 and LY6/L92/L94/L9H 6.0-6.2: 58x reluctor, front-cover cam sensor
  • AFM and VVT on many
Sourced · medium109
GMT900 ECM

E38 ECM (two connectors), CAN-based, with a separate TCM for the 6L80/6L90

Sourced · medium194
Anti-theft
  • PCMs are tied to the vehicle's anti-theft/BCM
  • A donor PCM usually needs reprogramming to run without it
Low confidence31

Identify the donor before buying: model year, RPO code (on the glovebox or door label), reluctor type and whether AFM/VVT is fitted. These determine the controller and harness. Truck harnesses are long and often damaged during removal, so many swappers buy a reworked or new standalone harness.

Factory ECU pinout: pending

No OEM pin table is in our library yet for the 5.3 LM7 / L59 / LY5 (Gen III/IV truck) factory ECU. No OEM-grade public pinout was found. Needed: the GM service manual Engine Controls / Wiring Systems section for this vehicle and year, giving the PCM/ECM connector end views and terminal tables. Specifically the GMT800 (1999-2007) and GMT900 (2007-2014) light-duty truck service manuals, PCM/ECM connector terminal tables. Until then, wire from the harness maker's instructions or the factory service manual.

Factory ECU pinout

No OEM-grade public pinout was found. Needed: the GM service manual Engine Controls / Wiring Systems section for this vehicle and year, giving the PCM/ECM connector end views and terminal tables. Specifically the GMT800 (1999-2007) and GMT900 (2007-2014) light-duty truck service manuals, PCM/ECM connector terminal tables.

Harness: wire-in

Route for this carWire-in
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

No plug-and-play harness for the S3 pinout is listed for this vehicle yet. The route is a universal wire-in harness: the factory ECU is removed and each circuit is wired to the new ECU from a pinout. Nothing is written to the factory ECU.

Plug-and-play

Being researched

We're mapping S3 plug-in and factory-connector adapter harnesses to this application.

Wire-in

Universal flying lead or re-terminated factory harness

Always available: terminate the engine side to ECU2's two Superseal 34 connectors. Universal harness from $405 USD list.

Your GAINS system for this car · pre-release

ECU2 for the Silverado / Sierra / Tahoe / Yukon GMT900

Planned with the same rules as the configurator for this car's 8 cyl · port injection · cable or drive-by-wire. The factory ECU is unplugged and replaced; nothing is written to it.

Chevrolet / GMC Silverado / Sierra / Tahoe / Yukon GMT900 5.3 (LY5 / LMG / LC9) studio render
Silverado / Sierra / Tahoe / Yukon GMT900
  • ECU2Engine controller

    8 cyl · port injection · cable or drive-by-wire

    Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • Drive-by-wire built inFour half-bridges run up to two electronic throttles, with pedal and throttle sensors on the ECU's own inputs and a windowed watchdog that cuts the motors in hardware on a fault.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harnessNone listed for this car
  2. Factory-connector → S3 adapterNone listed for this car
  3. Wire-inYour route: universal wire-in harness

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Silverado / Sierra / Tahoe / Yukon GMT900

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Cylinder deactivationbuild choice

    AFM / DFM / MDS / VCM is disabled in the build, with the lifter and valley-plate work the engine's guidance calls for.

  4. 4
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  5. 5
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAF+MAP (blended / torque model) (low confidence)

  6. 6
    Wideband sensorhardware

    factory O2 type not yet sourced; plan on a Bosch LSU 4.9 for the GAINS ECU's built-in controller

  7. 7
    Bottom end and head sealingfactory reference

    Reported: Powder-metal rods and cast pistons are commonly reported as the first limits. Stock-bottom-end turbo 4.8/5.3 race engines exceeding 1,000 hp have been reported (EngineLabs) but are described as a "ticking time bomb" without preparation. (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Drivetrain

GMT900 six-speed

6L80/6L90 integrate the TCM with the valve body and only work with a CAN-speaking 58x ECM such as the E38

Low confidence4
Tap-shift and gear display

On GMT900 the tap-up/tap-down and cluster gear display run through the BCM, so transmission swaps can need BCM and cluster changes

Low confidence12

GMT800 trucks pair Gen III engines with four-speed automatics controlled by the PCM. That single-module control is one reason the 24x truck engine plus 0411-type PCM is the default budget swap package.

Chassis integration

Gen IV networking
  • Gen IV ECMs were designed for CAN-networked vehicles
  • A Gen III PCM lacks the CAN features GMT900 modules expect
Low confidence1112

In a GMT900 the cluster, BCM, TCM and ABS all exchange data with the ECM over GMLAN (CAN). Replacing the ECM with a non-GM controller means providing those messages or accepting lost functions such as the gauges, cruise and shift display.

Tuning notes

AFM
  • Collapsed or stuck AFM lifters on Gen IV truck engines are widely reported
  • Conversion to non-AFM lifters is a common fix
Low confidence13
Load model
  • MAF plus VE-table speed density
  • Tuners force speed density by changing the MAF failure and high-rpm disable settings
Sourced · medium6

Iron-block truck engines are the budget boost platform. Stock injectors are sized for truck power, so plan injectors and fuel pump together with boost. Disable AFM in the calibration before changing the cam, and remove the AFM hardware for any serious build.

Popular swaps

Popular donorsLM7 5.3, LQ4/LQ9 6.0 (Gen III) and LY5/LY6 (Gen IV)Sourced · medium107
0411 into older trucks
  • 0411 PCMs can be installed in 1996-2000 GMT400 trucks by re-pinning the connector terminals
  • Wiring differs by year
Low confidence5

GAINS on the Silverado / Sierra / Tahoe / Yukon GMT900

ECU2

ECU2Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

Which truck LS engines are 24x and which are 58x?

GMT800-era 4.8, 5.3 and 6.0 engines through about 2006-07 are 24x. GMT900 2007-on truck engines are 58x with the cam sensor in the front cover.92

What is the best PCM for a 5.3 junkyard swap?

For a 24x Gen III engine, the 0411-type P01 PCM is the common choice because it runs engine and transmission in one unit and is widely supported by reflash tools. A 58x engine needs an E38 (or a conversion module to a Gen III PCM).152

Can I run a 6L80 with a Gen III PCM?

No. The 6L80/6L90 has an integrated TCM that only works with a CAN-based 58x ECM such as the E38.49

Should I delete AFM on a 5.3?

For cam upgrades or a standalone ECU, most builders replace AFM lifters with non-AFM parts and block the AFM oil supply instead of only disabling it in software.131

What are the bore and stroke of the 5.3 Vortec?

Gen IV 5.3 engines (LY5, LC9, LMG, LH6) are listed at 3.78 x 3.622 in.10

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. LS Engine Controllers, Making Your LS-Power Change A Controlled Swap · Chevy Hardcore · press · retrieved 2026-10-25
  2. Dialing In LS Sensors For Various Generations With Michigan Motorsports · EngineLabs · press · retrieved 2026-10-25
  3. 0411 PCM VATS/BCM discussion · GM Square Body forum · community · retrieved 2026-10-25
  4. 6L80E swap (forum thread) · GM-Trucks.com · community · retrieved 2026-10-25
  5. 12200411 PCM swap for 1996 to 2000 GMT400 trucks (forum thread) · GMT400.com · community · retrieved 2026-10-25
  6. Speed Density Mode - GM Vehicle · HP Tuners · vendor-doc · retrieved 2026-10-25
  7. GM LS Engine RPO Codes Explained: LM7, L59, LQ4, LQ9 and L33 · JEGS · vendor-doc · retrieved 2026-10-25
  8. Navigating Gen-III LS Drive-By-Wire Throttle Bodies With PSI · LSX Magazine · press · retrieved 2026-10-25
  9. 24x vs 58x Reluctor Differences for LS and LT · PSI Conversion · vendor-doc · retrieved 2026-10-25
  10. Tech: LS engine core options · Street Machine · press · retrieved 2026-10-25
  11. Differences and Applications of GM ECMs (Gen III, IV and V) · The Tuning School · community · retrieved 2026-10-25
  12. 6 speed Auto conversion (forum thread) · Tahoe Yukon Forum · community · retrieved 2026-10-25
  13. Another 5.3 AFM Dead Lifter Issue (forum thread) · Tahoe Yukon Forum · community · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  • Catalog note: AFM on later engines
  • Factory ECU part numbers not yet sourced for this vehicle.
  1. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  2. E-941 S3 engine harness availability (inferred, medium confidence)