Bosch · Hall effect (digital)

Bosch Mini-HA-P sealed Hall-effect speed sensor

Bosch Motorsport F02U.V03.778-01Bosch Motorsport F02U.V03.778-90

The Bosch Mini-HA-P sealed is a Hall-effect speed sensor for camshaft, crankshaft and wheel speed, up to 10 kHz at a 0.2-1.5 mm air gap. It runs on 5-18 V, and its open-collector, active-low output needs a pull-up (Bosch specifies it for a 1 kΩ load). The flying-lead version uses red supply, green signal and black ground.2

Key specifications

Measures: Tooth or gap on a ferromagnetic target wheel, from standstill. Output: Hall effect (digital).

Max frequency≤ 10 kHzSourced2
Air gap0.2-1.5mmSourced2
Supply5-18V, 10 mASourced2
Output
  • Open collector for 1 kΩ, active low
  • 0.4 V to < US
Sourced2
Edge repeatability
  • < 3 %≤ 6 kHz
  • < 5 %≤ 10 kHz
Sourced2
Temperature-40 to 150°CSourced2
Mounting16 mm bore, 1 × M6, 8 N·mSourced2
Part numberMakerNote
F02U.V03.778-01Bosch MotorsportWith ASL606-05PC-HE connector2
F02U.V03.778-90Bosch MotorsportFlying leads, no connector2

Pinout and connector

12345Schematic, pin-number order (positions not published)
Schematic in pin-number order: the maker does not publish cavity positions. Mating face labels. Pin functions from the maker's document. Our drawing from the published pin list, not a maker drawing.
  • Supply
  • Ground / return
  • Signal
  • Shield
  • Not used / not listed
Download pinout (SVG)
PinFunction (as published)Typical ECU inputWire note
1Supply (US)Sensor supply (5-18 V per maker)Red (published)
2GroundSensor groundBlack (published); Return to sensor ground, not chassis
3SignalCrank/cam trigger input (digital, pull-up)Green (published)
4Not connectedLeave unconnected—
5Not connectedLeave unconnected—

Wire colours apply to the flying-lead version (F02U.V03.778-90); pins 4 and 5 of the connector version are not connected.2 The ECU-input and wire columns are our general guidance, not the maker's.

Connector: ASL606-05PC-HE; mating part ASL006-05SC-HE (F02U.000.228-01)2 Connector library

Terminals and seals: Not listed: the Bosch data sheet gives the mating housing only, not contact or seal part numbers.

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Trigger setup

  • Trigger type: Hall effect (digital square wave).2
  • Max frequency: ≤ 10 kHz.2
  • Air gap: 0.2-1.5 mm.2
  • Output: Open collector for 1 kΩ, active low; 0.4 V to < US.2
  • Trigger edge: not published by the maker. Confirm the edge your ECU uses with a scope or a timing light before running the engine.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedCRANK (pin 13) or CAM (pin 15) accept Hall in the concept, but the pull-up on these inputs is still an open item.Medium3
Haltech (Elite / Nexus)Configurable (generic input)Trigger or Home input in digital mode with the 5 V pull-up selected.Medium7
Link (G4X)Configurable (generic input)Trigger input; Link sells a Hall sensor kit listed for all Link ECUs.Medium8
MoTeC (M1)UnverifiedThe M150 page lists programmable digital inputs but does not name Hall trigger sensors.No public source
ECUMaster (EMU Black)Configurable (generic input)Trigger input (3: primary and 2 cams), Hall or VR selected in software.9
AEM (Infinity)Configurable (generic input)Crank or cam Hall input (10 kΩ pull-up to 12 V per AEM).10
MaxxECUConfigurable (generic input)Trigger input in digital mode, or an extra digital input for speed sensors.11
Holley (Terminator X / EFI)Configurable (generic input)Crank or cam input; Holley recommends Hall sensors.12

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Supply, ground and signal; the signal needs a pull-up to the ECU's logic level because the output only pulls low.2

Hall sensors are less noise-sensitive than VR sensors but still benefit from routing away from ignition wiring.Medium1

Failure modes and checks

Signal stuck high

Likely cause No target in range or air gap too large

Check Set 0.2-1.5 mm and confirm a tooth passes the sensor face.Medium2

Signal stuck low or absent

Likely cause No pull-up on the input

Check Enable or fit a pull-up; the output is open collector.Medium2

Test it with a multimeter

  • With the supply connected and a pull-up on the signal, the signal pin should switch between near 0 V and the pull-up voltage as a tooth passes (turn the engine slowly). Maker output: Open collector for 1 kΩ, active low; 0.4 V to < US.2

Frequently asked

Does the Bosch Mini-HA-P need a pull-up?

Yes. Its output is open collector, active low, specified for a 1 kΩ load, so the input needs a pull-up to its logic level.2

What are the wire colours of the Bosch Mini-HA-P?

On the flying-lead version: red supply, green signal, black ground.2

Related

Use it with GAINS

Bosch Mini-HA-P sealed Hall-effect speed sensor on GAINS hardware

ECU2CRANK (VR or Hall, single-ended, adaptive threshold)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only. Hall pull-up arrangement to be confirmed in the schematic.Medium3

ECU2CAM (VR or Hall, single-ended)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Shielded, drain at the ECU end only

Shielded cable, shield to sensor ground at the ECU end only.Medium3

ECU2Digital/frequency input personality

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

For wheel speed: INJ5-6 or IGN5-6 as a frequency input with the 2.2 kΩ pull-up.Medium3

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

12 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Speed Sensor Hall-Effect Mini-HA-P sealed data sheet 69875339 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  5. MINI HA P SEALED product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  6. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  7. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  8. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  9. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  10. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.