Sequential fuel injection (vs batch fire)

sequential injectionSFISEFItimed injectionfully sequentialbatch firebatch-fire injectionsimultaneous injectiongroup injectionsemi-sequential

Sequential fuel injection is a mode in which each cylinder's injector fires once per engine cycle, timed to that cylinder's intake stroke. It needs cam-phase information so the ECU knows which cylinder is on intake. The older alternative, batch fire, opens groups of injectors together without timing them to individual cylinders.12

How it works

With sequential injection the ECU triggers each injector individually.

Timing is usually set as an end-of-injection angle, so fuel delivery finishes at a chosen crank angle before or after the intake valve opens.12

A crank sensor alone cannot distinguish compression from exhaust TDC, because the crank turns twice per cycle. A cam sensor adds the missing phase so the ECU can match each injection to the correct cylinder.23

Timing changes fuel behaviour. Aquino's 1981 SAE study identified injector phasing, alongside wall wetting and manifold filling, as a cause of air-fuel ratio transients. Injecting onto a closed valve improves evaporation from hot surfaces; injecting into an open valve carries more liquid fuel into the cylinder.43

Batch fire vs sequential

Batch-fire systems open groups of injectors, or all of them, at the same moment, usually once or twice per cycle. Simultaneous systems fire every injector together; banked systems fire sets of cylinders. Fuel sprayed onto a closed intake valve waits in the port until the valve opens.12

Why batch fire existed

Early electronic systems needed no cam-phase sensor and fewer output drivers if injectors were grouped. Splitting each cycle's fuel into two half-pulses also smoothed delivery with the slower injectors of the time. Semi-sequential is the middle step: companion cylinders fire in pairs once per crank revolution, still without cam phase.Medium12

What batch fire costs

Each cylinder receives its fuel at a different point relative to its own valve events, so fuel residence time on the port wall varies cylinder to cylinder. Mixture can differ between cylinders, mostly at idle, light load and in transients. At full load the same fuel arrives either way, so power differences are small.Medium342

Typical values

Injections per cycle

Sequential: one per cylinder, timed to its intake event. Semi-sequential: two, in companion pairs. Batch fire: one or two, groups or all injectors together.

Sourced12
Phase signal needed

Sequential: crank plus cam (or other cycle-phase) signal. Semi-sequential and batch fire: crank only.

Sourced23
Injector drivers

Sequential: one per cylinder. Batch fire: one per group, so fewer outputs.

Sourced · medium1
Where the difference shows
  • Idle quality, emissions, economy and transient response
  • Little difference at full load.
Sourced · medium34
Fallback

Many ECUs drop from sequential to batch or semi-sequential when the cam signal fails.

Sourced · medium2

In tuning

Sequential timing is calibrated for idle quality, emissions and transient response, and cylinder-specific trims become possible.

At high rpm the time per cycle shrinks, so long pulses overlap valve events no matter what timing is chosen.Medium23

If the cam signal fails, many ECUs fall back to batch or semi-sequential mode. Check the fallback behaviour before relying on sequential-only features such as per-cylinder trim.Low2

Batch fire usually splits fuel into two injections per cycle, which halves each pulse. With large injectors at idle that can push each pulse into the non-linear short-pulse region, so injector dead time and short-pulse data matter more than in sequential mode.Medium23

Formula and worked example

Try it

ms
rpm

Result

Duty cycle81.3 %
Time per engine cycle18.46 ms

Planning estimate from the formula below, not a measurement.

Open the full injector duty cycle calculator →

Myths vs facts

Myth Sequential injection always makes more power.

Fact At full load, power is limited by airflow and mixture, not injection mode. The gains from sequential timing show mostly in idle, emissions, economy and transients.Medium34

Myth A crank trigger is enough for sequential injection.

Fact A crank-only signal repeats every revolution and cannot tell which half of the four-stroke cycle a cylinder is in. Cam phase information is needed.23

Myth Batch fire cannot make good power.

Fact At high load, airflow and fuel quantity set power. Batch fire can deliver the same fuel; its drawbacks show mostly at idle, light load and in emissions.Medium32

Myth Batch fire wastes fuel by spraying into closed valves.

Fact Fuel sprayed onto a closed valve sits in the port and enters on the next intake event. The issue is mixture uniformity, not lost fuel.Medium31

Frequently asked

What is the difference between batch fire and sequential?

Sequential fires each injector once per cycle at a chosen point in that cylinder's intake stroke, which needs a cam-phase signal. Batch fire opens groups of injectors together, usually twice per cycle, using only crank position. Sequential gives better idle, emissions and transients; at full power they are close.Medium123

Is sequential injection better than batch fire?

For emissions, idle quality and transient response, generally yes, because each injection can be timed to the valve event and trimmed per cylinder. At full load power differences are small. Batch fire is simpler, needs no cam sensor and remains a valid fallback mode.Medium14

Does sequential injection need a cam sensor?

Yes, or another source of cycle phase. The crank turns twice per four-stroke cycle, so crank signals alone cannot tell the ECU which cylinder is on its intake stroke. Some systems infer phase from other signals, but a cam sensor is the usual solution.23

What injection timing should I use?

There is no universal value. Many calibrations end injection before the intake valve opens at light load so fuel evaporates off the hot valve, and test later timing for emissions and response. Treat timing as a calibration parameter tested with logged lambda and emissions.Low34

What is semi-sequential injection?

Semi-sequential fires injectors in pairs, typically companion cylinders that share crank position, once per crank revolution. It does not need cam phase and gives more regular timing than full batch fire, but each injector still fires twice per cycle with half the fuel each time.Medium12

Why do batch systems fire twice per cycle?

Splitting fuel into two smaller pulses per cycle spreads delivery more evenly relative to each cylinder's valve events, which reduces cylinder-to-cylinder variation. The drawback is shorter pulses, which makes dead-time accuracy and short-pulse behaviour more significant at idle and light load.Medium23

Can I switch from batch fire to sequential?

You need one injector driver per cylinder, a cam-phase signal, and an ECU that supports sequential mode. Wiring changes from paired to individual injector outputs. After switching, re-check idle and transient fueling, since injection timing changes mixture behaviour and wall-film dynamics.Medium12

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Fuel injection · Wikipedia · reference · retrieved 2026-10-25
  2. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-25
  3. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  4. Transient A/F Control Characteristics of the 5 Liter Central Fuel Injection Engine (Aquino, SAE 810494, 1981) · SAE International · sae-paper · retrieved 2026-10-25