Injector duty cycle

IDCduty cycleinjector dutyinjector utilisation

Injector duty cycle is the percentage of each engine cycle that a fuel injector is held open. For a four-stroke engine it equals pulse width divided by the time for two crankshaft revolutions. It shows how close an injector is to its maximum flow.12

How it works

Injector duty cycle depends on both pulse width and engine speed.

A four-stroke cylinder fires once every two revolutions, so the time available per cycle is 120,000 ÷ rpm milliseconds. At 6,000 rpm that is 20 ms; at 7,000 rpm it is about 17.1 ms.1

Pulse width grows with load, while available time shrinks with rpm. Peak duty therefore usually occurs at peak power, high in the rev range at full load.12

Near 100% the injector no longer closes between events, becomes effectively static, and can no longer meter fuel. Each solenoid also needs time to close and reopen, so the useful upper limit is below 100% and depends on the injector.Medium2

In tuning

Duty cycle is the quick check for injector sizing.

Many calibrators plan for a ceiling of roughly 80% to 85% at peak power, leaving room for hot fuel, low voltage and future changes; this is a common rule of thumb rather than a manufacturer limit.Low21

On sequential systems, high duty also means injection overlaps the closed-valve period, which changes mixture preparation. If duty is high, consider larger injectors or more fuel pressure, then re-characterise flow and dead time.Medium21

Formula and worked example

IDC (%) = PW × RPM / 1,200
IDC
injector duty cycle%
PW
total injector pulse width per cyclems
RPM
engine speed; 1,200 comes from 120,000 ms·rpm per cycle ÷ 100%rev/min
1

Try it

ms
rpm

Result

Duty cycle81.3 %
Time per engine cycle18.46 ms

Planning estimate from the formula below, not a measurement.

Open the full injector duty cycle calculator →

Myths vs facts

Myth Injector duty cycle above 80% always damages injectors.

Fact The 80% figure is a planning margin, not a physical limit. The real risks are losing metering control near static flow and having no headroom for heat or voltage changes.Low2

Myth Duty cycle tells you how much fuel is flowing.

Fact Duty is time open, not flow. Fuel pressure, injector size and dead time decide how much fuel that open time delivers.21

Frequently asked

How do you calculate injector duty cycle?

Multiply pulse width in milliseconds by rpm and divide by 1,200 for a four-stroke engine. That is the same as dividing pulse width by the cycle time, 120,000 ÷ rpm. For example, 10 ms at 6,000 rpm is 10 × 6,000 ÷ 1,200 = 50% duty.1

What is a safe maximum injector duty cycle?

A common planning target is about 80% to 85% at peak power. That margin covers hot fuel, voltage sag and pressure drop. It is a rule of thumb rather than a manufacturer rating, so check the injector maker's data for minimum off-time if you plan to run higher.Low2

What happens at 100% injector duty cycle?

The injector stays open continuously and flow is limited by its static rate and fuel pressure. The ECU can no longer add fuel by lengthening the pulse, so any further airflow makes the engine run lean. Treat it as a hard limit.21

How is duty cycle used to size injectors?

Work out the fuel flow the engine needs at peak power, usually from power times brake specific fuel consumption, then divide by the number of injectors and the maximum duty you will accept. The result is the static flow each injector must supply at your fuel pressure.Medium31

Why does duty cycle rise with rpm?

The time per engine cycle falls as rpm rises, while the fuel needed per cycle stays roughly constant at full load. The same pulse width therefore occupies a larger share of a shorter cycle, so duty peaks near the top of the rev range.1

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  2. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-25
  3. Brake-specific fuel consumption · Wikipedia · reference · retrieved 2026-10-25