Injector dead time (latency)

dead timeinjector latencyinjector offsetopening timebattery voltage offset

Injector dead time is the part of a commanded injector pulse during which little or no fuel flows, because the solenoid needle takes time to open and close. ECUs add it to every pulse, and it lengthens as battery voltage falls and fuel pressure rises.123

How it works

A port fuel injector is a solenoid valve.

When the ECU switches it on, current must build in the coil before magnetic force overcomes the spring and fuel pressure, and the needle needs time to travel. Closing also takes time. The net effect is that delivered fuel lags the electrical pulse.32

Injector dead time is the offset that linearises this. Delivered fuel is roughly proportional to pulse width minus dead time over most of the range, so the ECU computes the effective pulse needed and adds dead time on top.32

Supply voltage sets how quickly coil current rises, so lower voltage means longer dead time. A 2025 SAE paper studied this voltage effect directly. Higher fuel pressure pushes against the needle, which also lengthens opening time.13

At very short pulses the needle may not fully open before it is told to close. Injector output in that region is non-linear and less repeatable, which matters at idle with large injectors.Medium32

In tuning

Dead time errors show up most where pulses are short.

Because the same absolute error is a larger fraction of a short pulse, a wrong value makes idle and light cruise noticeably rich or lean while full load barely changes. Mixture that shifts when the alternator's charging voltage changes is a classic sign.Medium31

Use characterisation data measured for your exact injector at your fuel pressure, across the voltage range. Published values for the same injector family often disagree because of test pressure and driver differences, so verify with logged lambda while varying system voltage.Medium14

Formula and worked example

PW_cmd = PW_eff + t_dead(V_batt, ΔP)
PW_cmd
pulse width the ECU commandsms
PW_eff
effective pulse width needed for the fuel mass, from static flowms
t_dead
dead time, a function of battery voltage and differential fuel pressurems
31

Try it

hp
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

%

Size for 80-85% so the injector still has control margin at peak power.

Result

Flow per injector75.0 lb/hr
Total fuel flow240 lb/hr

Planning estimate from the formula below, not a measurement.

Open the full fuel injector size calculator →

Myths vs facts

Myth Dead time is a fixed number for each injector.

Fact It varies with battery voltage, differential fuel pressure and the driver circuit, so ECUs store it as a table, usually against voltage and often pressure.13

Myth Dead time errors only matter on big injectors.

Fact Any injector shows the error at short pulses. Large injectors just spend more time at short pulses, which makes the problem more visible at idle.Medium32

Frequently asked

What is injector dead time?

It is the delay between the ECU switching an injector on and fuel actually flowing at its full rate, net of the closing delay. ECUs add it to every pulse so delivered fuel matches the calculated amount. It is measured in milliseconds and depends on voltage and fuel pressure.31

Why does dead time increase at low voltage?

The coil's current rises more slowly with less voltage, so it takes longer to build enough magnetic force to lift the needle against the spring and fuel pressure. Lower system voltage therefore means a longer opening delay and a larger dead-time value.13

How do I find dead time for my injectors?

Use flow-bench data measured for your injector part number at your fuel pressure, ideally from the injector supplier's test sheet. If none exists, a bench flow test at several voltages is best. Verify in the car by logging lambda at idle while changing system voltage.Medium14

What happens if injector dead time is wrong?

Idle and light-load mixture will be off, and it will shift as voltage changes, for example when the cooling fan or headlights switch on. Full-load mixture is barely affected. Correcting the fuel table to hide a wrong dead time makes the error return whenever voltage moves.Medium31

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Influence of Supply Voltage over Fuel Injector's Deadtime (SAE 2025-36-0174) · SAE International · sae-paper · retrieved 2026-10-25
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  3. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-25
  4. Injection Valve EV 14 data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-25