Closed loop vs open loop fueling

closed loopopen loopclosed-loop fuelingopen-loop fuelingclosed-loop lambda controlO2 feedback controlpower enrichmentPE mode

Closed loop and open loop are the two ways an ECU sets fuel. In open loop it delivers fuel from calibrated tables with no check on the result. In closed loop it reads an exhaust oxygen sensor and keeps correcting fuel to hold a lambda target. Engines switch between them many times on every drive.123

How it works

Open loop

The ECU calculates the air entering each cylinder, picks a target lambda and computes the fuel. It still applies corrections for coolant and air temperature, battery voltage and throttle movement, but nothing measures whether the mixture came out right. Any error in the air estimate, injector data or fuel pressure goes straight into the mixture.12

Closed loop

The ECU starts from the same base fuel, then compares the oxygen sensor reading with the target and trims fuel up or down. The loop absorbs part-to-part variation, wear, fuel changes and small calibration errors that a fixed table cannot. It acts after a delay, because exhaust has to travel from the cylinder to the sensor.134

When each mode runs

A warm engine at idle and steady cruise is normally in closed loop. Open loop covers cold start and warm-up before the sensor is ready, heavy load and wide-open throttle, deceleration fuel cut, and any fault that makes the feedback untrustworthy. OBD-II reports this state directly: PID 03 distinguishes open loop for low temperature, open loop for load or decel fuel cut, open loop for a system fault, and closed loop.1510

Narrowband feedback

A conventional zirconia sensor switches sharply at λ 1 and reads only rich or lean, not how far. The ECU therefore ramps fuel leaner until the sensor flips lean, then richer until it flips rich. The mixture oscillates around stoichiometric, and that dither suits the three-way catalyst, which stores oxygen on lean swings and releases it on rich ones.341

Wideband feedback

A wideband (planar pump-cell) sensor reports the actual lambda over a wide range. Bosch rates its LSU 4.9 from rich mixtures around λ 0.65 up to free air. Because the controller knows the size of the error, it can correct proportionally and hold targets other than stoichiometric, including the rich targets used under load.Medium74

Short and long-term trims

The closed-loop correction is reported as short-term fuel trim, which moves constantly, and long-term fuel trim, a slower learned value that shifts the base fuel so the short-term trim can return near zero. A positive trim means the ECU is adding fuel because it sees lean; negative means it is removing fuel. SAE J1979 scales the OBD-II value from -100% to about +99.2%.9106

The transitions

Entry to closed loop usually waits for a hot, switching sensor, a coolant threshold and a short delay after start. On leaving closed loop for heavy load, the ECU switches to its power-enrichment target; many systems keep applying the learned long-term trim in open loop, so a large learned value can mask or shift open-loop errors. Re-entry after fuel cut or enrichment is often delayed so the sensor and catalyst settle first.Medium621

Why WOT runs open loop

Maximum power comes slightly rich of stoichiometric, and boosted or hot-running engines go richer still for knock and exhaust-temperature margin. A narrowband sensor cannot measure those rich mixtures, so OEM engines traditionally follow a calibrated enrichment table at full load. Response time matters too: a short full-throttle event can be over before a slow feedback loop has done anything useful.142

Closed loop on a wideband in modern standalones: with a wideband sensor the ECU can read a target lambda table and correct toward it across the map, including under boost. A 2016 US patent for an aftermarket engine controller describes exactly this: a target lambda that is stoichiometric at light load and richer at high load and cold, with the fuel adjustment capped by configured limits. The base table still has to be right; the loop only trims within its authority.Medium117

Typical values

Feedback

Open loop: none, fuel comes from tables and corrections. Closed loop: exhaust oxygen sensor reading compared with a lambda target.

Sourced12
Typical operating conditions

Open loop: cold start, warm-up, heavy load and WOT, decel fuel cut, sensor faults. Closed loop: warm idle and steady cruise.

Sourced110
Typical target

Closed loop (narrowband): oscillates around λ 1. Open loop at full load: richer than λ 1 for power and component temperature.

Sourced31
Sensor needed

Narrowband: closed loop around λ 1 only. Wideband: closed loop to any target in its range (LSU 4.9: about λ 0.65 to free air).

Sourced · medium47
What shows on a scan tool
  • PID 03 fuel system statusclosed loop, or open loop with the reason
  • PIDs 06-09 short- and long-term fuel trim per bank, -100% to +99.2%.
Sourced109
Main risk

Open loop: base-table error goes uncorrected. Closed loop: a bad sensor or exhaust leak steers fuel the wrong way unless authority is limited.

Sourced · medium12

Symptoms and causes

Engine stays in open loop when warm at cruise

Likely causes Failed oxygen sensor or sensor heater circuit, a coolant temperature sensor reading cold, or a stored fault that disables feedback.

Check Read PID 03: 'insufficient temperature' points at the coolant sensor or thermostat; 'system failure' points at a stored fault. Check the O2 sensor signal is switching.

Medium1056

Large positive trims at idle that shrink with load

Likely causes Unmetered air (vacuum leak) is a bigger share of total airflow at idle, so the loop adds fuel there.

Check Compare trims at idle and at 2,500 rpm; smoke-test the intake.

Medium6

Mixture fine at cruise but lean or rich at full throttle

Likely causes The open-loop enrichment table or the air model is off where feedback is not active; learned trims can hide it at cruise.

Check Log wideband lambda against the target through repeated full-load pulls.

Medium67

In tuning

Tune the base table so trims stay small.

If closed-loop or learned trims sit consistently positive in a load and rpm region, the base fuel reads lean there; consistently negative means rich. Correct the table or the air model rather than letting the loop carry the error, because open-loop regions and transients run on the base calculation alone.Medium62

Verify open-loop regions under real load. Log wideband lambda, rpm, load, air temperature and knock activity on repeated pulls, and confirm injector dead time, flow data and fuel pressure first, since open loop has nothing to hide their errors.Medium71

Limit closed-loop authority, especially at high load. Clamp the maximum correction and disable feedback on sensor faults, so a failed sensor, a cracked exhaust or an air leak ahead of the sensor cannot drive the mixture dangerously lean or rich.Medium2711

Try it

:1
%

0 for E0 gasoline, 10 for E10, 85 for nominal E85.

Result

Lambda0.850 :1
Stoichiometric AFR of this blend14.70 :1

Planning estimate from the formula below, not a measurement.

Open the full afr to lambda converter →

Myths vs facts

Myth Closed loop means the base fuel map does not matter.

Fact Feedback only corrects within its limits and after a delay. Transients and every open-loop condition run on the base map alone, so it still has to be accurate.Medium16

Myth Open loop means the ECU is in a fault mode.

Fact Open loop is normal at start-up, warm-up, heavy load and deceleration. It only indicates a fault when a warm engine at cruise should be in closed loop and is not.110

Myth A car in closed loop always runs exactly at 14.7:1.

Fact With a narrowband sensor the mixture oscillates around stoichiometric by design, and the stoichiometric AFR depends on the fuel. The average sits near λ 1, not a fixed AFR number.38

Myth Open-loop fueling ignores all sensors.

Fact Only the oxygen feedback is ignored. Air mass or manifold pressure, temperatures, battery voltage and throttle changes still drive the fuel calculation.12

Frequently asked

What is the difference between open loop and closed loop?

Open loop sets fuel from tables only, with no feedback on the result. Closed loop measures exhaust oxygen and adjusts fuel to hit a target. Engines use closed loop where a lambda target is stable and the sensor is ready, and open loop where they are not, such as cold start and full load.12

When does an engine go into closed loop?

Once the oxygen sensor is hot and switching and the engine has passed its warm-up conditions, usually a coolant temperature threshold and a short delay after start. It stays in closed loop at idle and cruise and drops out at heavy load, decel fuel cut and when faults are detected.Medium15

Why do engines run open loop at wide-open throttle?

Full-load targets are richer than stoichiometric for power and to control knock and exhaust temperature, and narrowband sensors cannot measure rich mixtures. The ECU therefore follows its calibrated enrichment table. Engines with wideband sensors can apply feedback there, usually with tight limits.14

Can you run closed loop at wide-open throttle?

With a wideband sensor, yes, and many standalone ECUs do: they correct toward a rich target lambda under load. Keep the correction authority small and disable it on sensor faults, so a failure cannot cause damage.Medium1172

Why is my car stuck in open loop?

Common causes are a failed O2 sensor or heater circuit, a coolant temperature sensor reading cold, or a fault code that disables closed-loop control. A scan tool showing PID 03 fuel system status gives the reason, and sensor readings narrow it down.Medium1056

Is open loop bad for an engine?

Not when intended, such as under heavy load or during warm-up. It is a problem when a warm engine is stuck in open loop at cruise, because mixture errors go uncorrected, emissions rise and fuel use goes up.Medium15

What is power enrichment?

Power enrichment is the open-loop mode in which the ECU richens the mixture once load or throttle passes a threshold. It supplies fuel for maximum power and adds margin against knock and high exhaust temperature. The threshold and the enrichment are calibration values.Medium12

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

11 sources
  1. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  2. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-25
  3. Lambda sensors: precisely measuring for an optimized combustion (workshop brochure) · Bosch Automotive Aftermarket · vendor-doc · retrieved 2026-10-25
  4. Oxygen sensors · Clemson University Vehicular Electronics Laboratory · reference · retrieved 2026-10-25
  5. Oxygen sensor · Wikipedia · reference · retrieved 2026-10-25
  6. Fuel Trim Diagnostics Have Changed · GEARS Magazine (ATRA) · press · retrieved 2026-10-25
  7. Lambda Sensor LSU 4.9 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-25
  8. Air-fuel ratio · Wikipedia · reference · retrieved 2026-10-25
  9. SAE J1979: E/E Diagnostic Test Modes · SAE International · standard · retrieved 2026-10-25
  10. OBD-II PIDs (service 01 PID 03 fuel system status; PIDs 06-09 fuel trim) · Wikipedia · reference · retrieved 2026-10-27
  11. US 9,371,792: Active tuning system for engine control unit (granted 2016-06-21) · US Patent and Trademark Office (via Google Patents) · reference · retrieved 2026-10-27