Target lambda table

lambda target tabletarget AFR tableAFR target mapcommanded lambdalambda mapdesired equivalence ratio

A target lambda table is an ECU map, usually indexed by engine speed and load, that sets the mixture strength the engine should run at each operating point. The fuel calculation uses it to size injection, and closed-loop control uses it as the setpoint for wideband or narrowband feedback.123

How it works

Model-based fueling separates two questions: how much air is in the cylinder, and what mixture the engine should run.

The airflow model, through a volumetric efficiency table or MAF, answers the first. The target lambda table answers the second, so changing a mixture target does not require retuning the air model.14

Targets differ by region. Idle and cruise on catalyst-equipped engines sit at λ 1, where a three-way catalyst works efficiently. High-load regions are usually richer to control exhaust and component temperatures and add knock margin.

Some engines run lean of λ 1 at light load where emissions rules allow.51

Lambda targets carry across fuels, which AFR targets do not. Gasoline is stoichiometric near 14.7:1 and E85 near 9.8:1, so a table written in AFR would need rewriting for each fuel. A lambda table stays valid; only the stoichiometric ratio used to compute fuel mass changes.26

In tuning

Set targets first, then tune the airflow model until measured lambda matches target with small corrections.

Large, consistent trims mean the air model is wrong, not the target. Keep targets smooth across cells so transitions do not cause steps in torque.Medium17

Full-load targets have no single right answer. Choose them from fuel, compression, charge temperature and turbine limits, then confirm with wideband, knock and exhaust temperature logs. Copying another engine's numbers is not a substitute for that data.Medium51

Formula and worked example

m_fuel = m_air / (λ_target × AFR_stoich)
m_fuel
fuel mass per cylinder per cyclemg
m_air
air mass per cylinder per cyclemg
λ_target
target lambda from the table
AFR_stoich
stoichiometric air-fuel ratio of the fuel
25

Try it

:1
%

0 for E0 gasoline, 10 for E10, 85 for nominal E85.

Result

Lambda0.850 :1
Stoichiometric AFR of this blend14.70 :1

Planning estimate from the formula below, not a measurement.

Open the full afr to lambda converter →

Myths vs facts

Myth Richer targets are always safer under boost.

Fact Extra fuel cools the charge, but too rich slows combustion, can misfire and washes oil from cylinder walls. Safe targets are engine-specific and need logged evidence.Medium51

Myth Changing a target lambda cell retunes the engine's fueling model.

Fact The target only states the desired mixture. If measured lambda misses the target, the airflow model or injector data is off and needs correcting there.Medium1

Frequently asked

What lambda should I target at idle and cruise?

Engines with a three-way catalyst normally target λ 1 at idle and cruise, because the catalyst only converts all three regulated pollutants efficiently near stoichiometric. Without a catalyst or emissions constraint, some calibrations run slightly lean at light cruise for economy, but that must be checked for drivability and legality.51

What lambda should a turbo car run at full load?

It depends on the engine, fuel and limits. Boosted gasoline engines are commonly run richer than λ 1 at full load to manage exhaust temperature and knock margin. Pick a starting value conservatively and refine it with wideband, knock and exhaust temperature logs rather than copying another engine's map.Medium51

How does the target lambda table work with the VE table?

The VE table, with pressure and temperature, estimates how much air is in each cylinder. The target lambda table says what mixture to run. The ECU divides air mass by target lambda and the fuel's stoichiometric ratio to get fuel mass. Tune VE so measured lambda matches target.142

Should I tune in AFR or lambda?

Lambda is simpler when fuels change, because λ 1 always means chemically correct mixture. AFR numbers depend on the fuel's stoichiometric ratio, so a 12.5:1 target means different mixtures on gasoline and E85. Wideband sensors also measure lambda directly, so lambda removes a conversion step.27

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Air-fuel ratio · Wikipedia · reference · retrieved 2026-10-27
  3. Engine control unit · Wikipedia · reference · retrieved 2026-10-27
  4. Volumetric efficiency · Wikipedia · reference · retrieved 2026-10-27
  5. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  6. Stoichiometry (air-to-fuel ratio of common fuels) · Wikipedia · reference · retrieved 2026-10-27
  7. Lambda Sensor LSU 4.9 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27