Acceleration enrichment (transient fueling and wall wetting)

acceleration enrichmentaccel enrichmenttransient fuel compensationtip-in enrichmentTPS-dot enrichmentMAP-dot enrichmentwall wettingfuel filmport wall filmx-taupuddling

Transient fueling, often called acceleration enrichment, is the ECU logic that adds or removes fuel during rapid load changes so the mixture stays on target. It compensates for fuel film on port walls, manifold filling and sensor delay that steady-state fuel tables do not model.12

How it works

When the throttle opens quickly, air reaches the cylinders sooner than some of the fuel.

Part of each injection lands on port walls and valve, and that film must grow before delivery to the cylinder matches injection. Without extra fuel, the engine momentarily runs lean, causing hesitation.12

Aquino's 1981 SAE study on a 5 L central fuel-injected engine traced air-fuel transients to wall wetting, manifold air charging and injector phasing. It modelled the film with a fraction of fuel that impacts the wall and a time constant for its evaporation.1

ECUs implement compensation in two broad ways. Rate-based systems add fuel in proportion to throttle or manifold-pressure rate of change. Model-based systems track the estimated wall film and inject extra or less fuel to cancel its effect.

On deceleration the reverse happens, so fuel is removed.Medium21

Wall wetting

Wall wetting happens because injected fuel does not all evaporate in flight. Some droplets strike the port wall and valve, forming a film that evaporates into the passing air over time. At steady state the film's inflow and outflow balance, so it is invisible in fuel tables.12

Temperature and the fuel film

Film behaviour depends strongly on surface temperature. A follow-up SAE paper studied local heating of the intake area as a way to improve air-fuel control. Cold walls hold more fuel for longer, which is why cold-engine transients are hardest to control.42

What happens without compensation

With the same illustrative X = 0.3 and τ = 0.5 s, a steady 1.0 g/s leaves a film of 0.3 × 1.0 × 0.5 = 0.15 g. If injection steps to 2.0 g/s with no compensation, the cylinder initially receives 0.7 × 2.0 + 0.15 ÷ 0.5 = 1.7 g/s, only 85% of the fuel injected, so the mixture briefly runs about 15% lean.Medium12

In tuning

Tune steady-state fueling first, then transients.

Log fast lambda, throttle, manifold pressure and pulse width at a high rate, and make repeatable tip-ins at several temperatures and rpm. Enrichment that is too small gives a lean spike and stumble; too much gives a rich bog.Medium32

Wall-film behaviour depends strongly on temperature, so cold engines need far more transient fuel than warm ones. Direct injection reduces but does not remove port film effects, since there is no port film but there can be cylinder-wall and piston film.Medium24

Injector targeting, spray quality and timing change film formation. A finer spray or different injection timing can reduce film mass, so changing injectors often requires retuning transient compensation even if steady flow matches.Medium62

Formula and worked example

ṁ_inj = (ṁ_cyl,des - M_f / τ) / (1 - X)
ṁ_inj
fuel flow the injector must deliverg/s
ṁ_cyl,des
desired fuel flow into the cylinderg/s
M_f
estimated wall-film massg
τ
film evaporation time constants
X
fraction of injected fuel that lands on the wall
12

Try it

:1
%

0 for E0 gasoline, 10 for E10, 85 for nominal E85.

Result

Lambda0.850 :1
Stoichiometric AFR of this blend14.70 :1

Planning estimate from the formula below, not a measurement.

Open the full afr to lambda converter →

Myths vs facts

Myth Acceleration enrichment fixes all tip-in stumbles.

Fact Lean spikes can also come from wrong dead time, a lagging load signal or ignition timing. Fix steady-state fuel and load sensing before adding transient fuel.Medium21

Myth Transient fuel only matters on cold engines.

Fact Film effects are largest cold but still present when warm, especially on port-injected engines with big throttle changes.Medium14

Myth Wall wetting only matters during cold start.

Fact Cold makes it worse, but warm port-injected engines still show film-driven lean spikes on tip-in and rich spikes on lift-off.Medium14

Myth Direct injection completely eliminates fuel film.

Fact DI removes the port film, but spray can still wet the piston crown and cylinder wall, especially when cold, which affects emissions and oil dilution.Medium27

Frequently asked

Why does my engine go lean when I stab the throttle?

Airflow rises almost instantly, but part of the extra fuel goes into building the wall film in the port rather than into the cylinder. Load sensors and calculations also lag. The result is a brief lean spike. Acceleration enrichment adds fuel to cover the film and the lag.12

What is TPS-dot enrichment?

It adds fuel in proportion to how fast the throttle position is changing. Because throttle movement leads airflow, TPS-dot reacts earlier than manifold pressure. MAP-dot enrichment does the same using the rate of manifold pressure change. Many ECUs blend both.Medium52

What is the x-tau model?

It is a wall-film model with two parameters: X, the fraction of injected fuel that lands on the wall, and tau, the time constant for that film to evaporate into the cylinder. Aquino's 1981 SAE paper described this approach, and it remains a common basis for transient compensation.1

How do you tune acceleration enrichment?

Get steady-state fueling right, then log fast lambda during repeatable throttle steps at different rpm and temperatures. Add enrichment until lean spikes disappear without rich overshoot, and check decel enleanment the same way. Retest when the engine is cold, because film effects grow sharply.Medium32

What is wall wetting in an engine?

It is liquid fuel that collects on intake port walls and the back of the intake valve after injection. The film acts as a fuel reservoir that fills and empties with a delay, so during throttle changes the cylinder receives a different amount of fuel than the injector delivered.12

How does temperature affect wall wetting?

Cold surfaces evaporate fuel slowly, so the film is larger and its time constant longer. Warm surfaces evaporate fuel quickly, shrinking the film. Calibrations therefore schedule film fraction and time constant against coolant or estimated port temperature, with the largest compensation at cold start.42

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Transient A/F Control Characteristics of the 5 Liter Central Fuel Injection Engine (Aquino, SAE 810494, 1981) · SAE International · sae-paper · retrieved 2026-10-25
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  3. Lambda Sensor LSU 4.9 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-25
  4. The Effect of Local Heating on A/F Ratio Control (SAE 820411) · SAE International · sae-paper · retrieved 2026-10-25
  5. US 5,255,655: Fuel injection system for an internal combustion engine · US Patent and Trademark Office · reference · retrieved 2026-10-25
  6. Effects of Fuel Atomization, Vaporization, and Mixing on the Cold-Start UHC Emissions of a Contemporary S.I. Engine with Intake-Manifold Injection (SAE 952482) · SAE International · sae-paper · retrieved 2026-10-25
  7. Gasoline direct injection · Wikipedia · reference · retrieved 2026-10-25