Port fuel injection

PFIMPImulti-point injectionmultiport fuel injectionMPFImanifold injection

Port fuel injection is a fuel-injection method with one injector per cylinder that sprays into the intake port, upstream of the intake valve. Fuel mixes with air in the port and enters the cylinder during the intake stroke, at pressures of a few bar.12

How it works

Port fuel injection replaced carburettors and throttle-body injection in most new gasoline cars by the early 1990s in developed markets. Electronic systems such as Bosch L-Jetronic, introduced in 1974, established the layout still used today.Medium1

Each injector is aimed at the back of the intake valve. Fuel lands on hot port walls and the valve, evaporates, and mixes with the incoming air. This gives good mixture preparation once warm, but some fuel forms a wall film, which complicates transients and cold starts.34

Port injectors run at low pressure, typically around 3 bar (43.5 psi) on many systems, and use simple saturated or peak-and-hold drivers. Bosch's EV 14 family is rated for 5 bar in production use and 8 bar for motorsport.52

Typical values

Where fuel goes

Port injection: into the intake port onto the back of the valve. Direct injection: straight into the cylinder.

Sourced16
Fuel pressure

Port: a few bar (about 3 bar on many systems; Bosch EV 14 rated 5 bar production, 8 bar motorsport). Direct: far higher, from a cam-driven pump.

Sourced56
Intake valve deposits

Port: fuel washes the valves. Direct: no fuel on the valves, so carbon can build up.

Sourced · medium67
Transient behaviour

Port: wall film needs acceleration enrichment. Direct: no port film, but spray can wet the piston and liner when cold.

Sourced · medium46
Dual injection

Some engines (for example Toyota D-4S) combine port and direct injectors

Sourced7

In tuning

Port injection gives freedom in injector sizing because injection can occur across most of the cycle, including while the valve is closed. Injection timing still affects emissions and transient response, especially on engines with tuned sequential timing.Medium32

Wall wetting is the main transient issue. Fuel deposited on the port takes time to evaporate, so tip-in and lift-off need compensation tables. Many high-power DI engines add port injectors to supply extra fuel at full load.Medium46

Try it

hp
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

%

Size for 80-85% so the injector still has control margin at peak power.

Result

Flow per injector75.0 lb/hr
Total fuel flow240 lb/hr

Planning estimate from the formula below, not a measurement.

Open the full fuel injector size calculator →

Myths vs facts

Myth Port injection is obsolete.

Fact Many current engines still use port injection, and several manufacturers pair it with direct injection to combine the strengths of both.Medium67

Myth Injection timing does not matter with port injection.

Fact Timing relative to valve opening changes how much fuel films on the walls and how it vaporises, which affects emissions and transient response.34

Frequently asked

Is port injection better than direct injection?

Each has strengths. Port injection is simpler, cheaper, keeps intake valves clean and allows long injection windows. Direct injection cools the charge and allows precise timing, but it needs high-pressure hardware and can build valve deposits. Some engines use both.Medium67

Why don't port-injected engines get intake valve carbon buildup?

Fuel sprayed onto the back of the intake valve continuously washes it, and detergent additives in gasoline help keep it clean. Direct injection removes that washing effect, which is why direct-injection engines without port injectors are more prone to intake valve deposits.Medium6

What fuel pressure does port injection use?

Many port systems run around 3 bar (43.5 psi) differential, though some returnless designs run higher. Bosch rates the EV 14 for up to 5 bar in standard use and 8 bar in motorsport. Check the injector rating before raising pressure.52

Can you add port injection to a direct-injection engine?

Yes, and it is a common way to add fuel for high power or E85, using an auxiliary rail and injectors in the intake manifold. It needs an ECU or controller that can drive and blend the extra injectors, plus fuel supply sized for both.Low62

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Fuel injection · Wikipedia · reference · retrieved 2026-10-25
  2. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-25
  3. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  4. Transient A/F Control Characteristics of the 5 Liter Central Fuel Injection Engine (Aquino, SAE 810494, 1981) · SAE International · sae-paper · retrieved 2026-10-25
  5. Injection Valve EV 14 data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-25
  6. Gasoline direct injection · Wikipedia · reference · retrieved 2026-10-25
  7. Toyota D-4S: Port Fuel Or Direct Fuel Injection? Why Not Both? · Tomorrow's Technician · press · retrieved 2026-10-25