Injector flow rate

injector sizestatic flow ratecc/minlb/hrg/min injector

Injector flow rate is the amount of fuel an injector delivers when held fully open at a stated pressure, given in cc/min, lb/hr or g/min. It sets how much fuel the engine can receive, and it changes with the square root of differential fuel pressure.12

How it works

Injector flow rate ratings are static flows at a reference pressure.

Bosch rates its EV 14 family at 3 bar (43.5 psi) using n-heptane, a test fluid with stable properties, and lists the family up to 1,000 g/min. Ratings at other pressures or fluids are not directly comparable.13

Mass and volume ratings differ by fuel density. Using 0.72 g/cc for gasoline, 1 lb/hr equals 453.6 g ÷ 60 min ÷ 0.72 g/cc, about 10.5 cc/min. A heavier or lighter fuel changes that conversion.Medium2

Flow through the metering orifice follows the orifice equation, so it scales with the square root of the pressure difference across the injector. Doubling differential pressure raises flow by about 41%, not 100%.42

The pressure that matters is differential: rail pressure minus the pressure at the injector tip, which is manifold pressure for port injection. Boost reduces differential pressure unless the regulator compensates.25

In tuning

Injector size, fuel pressure, dead time and short-pulse behaviour together define how the ECU converts fuel mass to pulse width.

After changing injectors, enter the new flow rate and dead-time data first, then confirm fueling, rather than rescaling the whole fuel table.Medium26

Raising fuel pressure is a quick way to gain flow, but the pump must supply that flow at the higher pressure, and injector opening slows at high pressure. Check both pump and injector ratings.Medium12

Formula and worked example

Q₂ = Q₁ × √(ΔP₂ / ΔP₁)
Q₁
rated flow at reference differential pressurecc/min
Q₂
flow at new differential pressurecc/min
ΔP₁
reference differential pressurebar
ΔP₂
new differential pressurebar
42

Try it

hp
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

%

Size for 80-85% so the injector still has control margin at peak power.

Result

Flow per injector75.0 lb/hr
Total fuel flow240 lb/hr

Planning estimate from the formula below, not a measurement.

Open the full fuel injector size calculator →

Myths vs facts

Myth Doubling fuel pressure doubles injector flow.

Fact Flow scales with the square root of differential pressure, so doubling pressure gives about 1.41 times the flow.42

Myth Injector ratings in cc/min are the same in any fuel.

Fact Ratings use a specific test fluid and pressure, often n-heptane at 3 bar for Bosch. Gasoline and E85 densities differ, so mass flow in the real fuel differs from the rating.1

Myth Bigger injectors always add power.

Fact Injectors only supply fuel the engine needs. Oversized injectors run short pulses at idle, where dead-time and non-linear behaviour make control harder.Medium24

Frequently asked

How do you convert cc/min to lb/hr?

Divide cc/min by about 10.5 for gasoline, or multiply lb/hr by 10.5 to get cc/min. That factor assumes a fuel density of 0.72 g/cc: 453.6 g per pound divided by 60 minutes and 0.72 g/cc gives 10.5. A different fuel density changes the factor.Medium2

How does fuel pressure affect injector flow?

Flow rises with the square root of the differential pressure across the injector. Going from 3 to 4 bar increases flow by about 15.5%, because the square root of 4/3 is 1.1547. Raising pressure also slows injector opening, so dead time increases.42

What size injectors do I need?

Estimate fuel flow from target power and brake specific fuel consumption, then divide by the number of injectors and your maximum planned duty cycle. For example, 400 hp at 0.50 lb/hp·h needs 200 lb/hr, or 31.25 lb/hr per injector on a V8 at 80% duty.Medium74

Why do Bosch injector ratings use n-heptane?

N-heptane is a pure compound with stable, repeatable density and viscosity, unlike gasoline, whose properties vary by blend and season. Using it lets flow ratings be compared between injectors and production batches. Real-fuel flow differs slightly from the n-heptane figure.Medium13

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Injection Valve EV 14 data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-25
  2. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-25
  3. Injection valves product overview · Bosch Motorsport · vendor-doc · retrieved 2026-10-25
  4. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  5. US 5,398,655: Manifold referenced returnless fuel system · US Patent and Trademark Office · reference · retrieved 2026-10-25
  6. Influence of Supply Voltage over Fuel Injector's Deadtime (SAE 2025-36-0174) · SAE International · sae-paper · retrieved 2026-10-25
  7. Brake-specific fuel consumption · Wikipedia · reference · retrieved 2026-10-25