RB26DETT Swap Nissan 240SX S14 (1995-98): RWD Conversion, Mounts, Gearbox and Import Guide

An RB26 S14 swap is a known but advanced swap: the GT-R engine left the factory only in all-wheel-drive cars, so it must be converted to rear drive. It takes RB swap mounts, a rear-drive oil pan, an RB25 five-speed, a custom driveshaft and a merged harness. The main hurdles are the RWD conversion, twin-turbo packaging, and US import and emissions rules.Medium56311

Difficulty4/5 · HardMedium563211
  • The RB26 came only with ATTESA E-TS all-wheel drive, so the pan and gearbox must change to rear-drive parts.
  • Mount kits list RB26 engine mounts for the S14, but the transmission mount options are for RB20 and RB25 gearboxes.
  • Builders report custom driveshafts and modified mounts, plus front-end packaging work for the twin turbos and intercooler.
  • The Skyline engine harness must be merged with S14 chassis wiring, and the six-throttle intake complicates engine management.
  • The engine was never sold in a US-certified vehicle, which makes import paperwork and emissions approval hard.

At a glance

The key numbers and parts, with the source on each tile.

Factory drivetrain
  • RB26DETT was fitted to ATTESA E-TS all-wheel-drive Skyline GT-Rs
  • The S14 is rear drive
Sourced13
Nissan rating
  • 206 kW at 6,800 rpm280 PS
  • 353 Nm (260 lb-ft) at 4,400 rpm1989 BNR32
Wikipedia notes the advertised figure followed a Japanese industry power cap and that later engines likely made more.Sourced1
Displacement2,568 cc inline six, 86 mm bore x 73.7 mm stroke156.7 cu inSourced12
Mounts

S13/S14 RB swap kit lists RB20, RB25 and RB26 engine mounts on the stock crossmember

Sourced5
Oil pan
  • The AWD RB26 pan will not clear
  • Use a rear-drive pan or a modified RB26 pan
Sourced · medium56
Gearbox
  • RB25DET rear-drive five-speed is the usual choice
  • GT-R gearboxes carry the AWD transfer
Sourced · medium56
S14 donor weight1,253 kg curb weight with the KA24DE2,762 lbSourced · medium4
US importAn engine for a car is declared to Customs on EPA Form 3520-1Sourced910

Recommended engines

  • RB26DETT · The Skyline GT-R engine with six individual throttles, a solid-bucket valvetrain and twin turbos. It only came from the factory in all-wheel-drive cars, so it needs a rear-drive oil pan and gearbox before it suits an S14.
  • RB25DET / NEO · Not the engine this guide is about, but the RB25DET donor supplies the rear-drive five-speed and pan most RB26 S14 swaps borrow; if the budget is tight, an RB25 is the simpler swap.

Mounts

An RB26 S14 swap usually starts with an RB swap mount kit that bolts to the stock S14 crossmember.

Kit contents

Left and right engine mounts, rubber transmission mount, two crossmember mounts, transmission brace, hardware

Sourced5
Engine coverageEngine mounts listed for RB20, RB25 and RB26 in S13 and S14Sourced5
Transmission mount choiceRB20 or RB25 rear-drive gearbox onlySourced5

One common kit lists its engine mounts for RB20, RB25 and RB26 blocks in both S13 and S14 chassis, with urethane engine bushings and a rubber transmission mount.5

The same kit only offers transmission mounts for RB20 and RB25 rear-drive gearboxes. That matches how most RB26 swaps are built: the GT-R block goes in with an RB25 five-speed behind it. One S14 builder still reported modifying the motor mounts, so plan a test-fit before final welding or paint.Medium56

Transmission

GT-R gearboxes

R32 and R33 five-speed, R34 Getrag six-speed, all built for ATTESA E-TS all-wheel drive

Sourced · medium3
Common choiceRB25DET five-speed from a rear-drive SkylineSourced · medium65
DriveshaftCustom one-piece shaft built for the swapSourced · medium6

The RB26 shares the RB bellhousing pattern, but every factory GT-R gearbox was built around ATTESA E-TS all-wheel drive, with a transfer section feeding a front driveshaft. That makes them a poor fit in the S14 tunnel. The usual answer is a rear-drive RB25DET five-speed, which is also what swap mount kits are designed around.Medium356

One documented S14 build considered R32 and R33 gearboxes and settled on an RB25 transmission, then modified the RB26 oil pan to suit it. The KA24DE gearbox does not share the RB bellhousing, so the stock S14 transmission stays out of the plan.Medium64

Expect a custom driveshaft. The same build used a one-piece shaft made for the swap. Measure only after the engine and gearbox sit on their final mounts at ride height, and make sure the front yoke matches the RB25 output spline.Medium6

Clearance

The RWD conversion starts at the sump.

Oil pan
  • AWD RB26 pan will not fit the S-chassis swap mounts
  • A rear-drive RB25DET pan is specified
Sourced5
Airflow meter placement

One S14 builder found the factory airflow meter position poor and removed it

Low confidence6

The GT-R pan carries the front differential housing and its output for the front axles, and that hardware hits the S-chassis crossmember area. The mount kit maker specifies a rear-drive RB25DET pan for clearance and says the AWD RB26 pan will not fit.Medium53

There are two routes. Fit a rear-drive pan with a matching oil pickup and dipstick, or have the factory RB26 pan cut and sealed where the front differential sat, as the documented S14 build did. Either way, confirm the pickup reaches the sump floor and the pan seals to the block before filling with oil.Low56

Up top, the six-throttle intake plenum, twin turbos and intercooler pipes all compete for space in a bay built for a four-cylinder. Check the steering shaft, brake lines, hood and strut towers as the engine goes in. The S14 builder above moved away from the factory airflow meter partly because of where it ended up.Low62

Cooling

The S14 radiator and fan were sized for a naturally aspirated 2.4-liter four rated at 155 bhp (116 kW).

Factory intercoolingTwin turbos feed an intercooler on the GT-RSourced · medium2
S14 original engine
  • KA24DE rated 155 bhp116 kW
  • Its radiator was sized for that
Sourced · medium4
Turbo coolingRB26 turbos are lubricated by engine oil pressureSourced · medium2

A twin-turbo six puts far more heat into the coolant, so plan a larger aluminum radiator and electric fans. The documented S14 build fitted an aluminum radiator as its main cooling change.Low46

Package the intercooler before the radiator. A front-mount core sits in the bumper opening, and its pipes have to reach both turbo outlets and the throttle plenum without crossing the radiator hoses. Leave room for the fan shroud and confirm airflow is not blocked by the core.Low26

Fuel

The S14 fuel pump fed a naturally aspirated four-cylinder.

S14 pumpSized for the naturally aspirated KA24DELow confidence4
Documented build

Replaced the pump and fitted larger injectors after removing the factory airflow meter

Sourced · medium6

An RB26 under boost needs more flow at higher pressure, so size a replacement pump for your power target and fuel type with a margin. The documented S14 build replaced the pump and fitted larger injectors as part of the swap.Low46

Exhaust

Factory turbosTwo turbos in parallel with ceramic turbine wheelsSourced · medium23
Factory boostWastegates hold boost to about 10 psi0.69 barSourced · medium2
Single-turbo conversion

One S14 build replaced the twins with a single turbo and manifold

Sourced · medium6

The factory RB26 runs two turbos in parallel, each feeding half the engine, with ceramic turbine wheels and wastegates that hold boost to about 10 psi (0.69 bar). In an S14, the two downpipes must merge and route past the steering shaft and transmission tunnel, which normally means a swap-specific or custom downpipe.Medium23

Some builders replace the twins with a single larger turbo on a new manifold, as the documented S14 build did. That simplifies the downpipe but changes the intake piping, oil and coolant lines, and boost control, so decide early. Treat ceramic factory turbine wheels as a stock-boost part.Medium63

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
Crank angle sensor
  • Driven from the exhaust cam
  • Reports crank and cam position
Sourced · medium2
ThrottlesSix individual throttle bodies in three siamesed pairsSourced · medium2
Ignition
  • Coil packs
  • The R34 GT-R has igniters built into the coils
Sourced · medium2

Any RB26 controller needs the cam-driven crank angle sensor signals, six injectors, six coils and their igniters, throttle position from the six-throttle intake, air temperature, coolant temperature, knock sensing and an oxygen sensor. Add a boost control solenoid and either the factory airflow meters or a manifold pressure sensor for load.Medium26

The GT-R engine harness is not plug-in. Merge it with the S14 chassis wiring for ignition and start feeds, fuel pump control, alternator, tachometer, coolant gauge, warning lights, fans and the A/C request. Leave the GT-R's all-wheel-drive circuits out; the S14 has no front driveline to control.Low34

Mount a standalone engine computer and any power distribution module (PDM) inside the cabin, behind the glovebox or a kick panel, away from turbo heat and water. Feed it from a fused, relay- or PDM-switched supply. Use PDM outputs or relays for the pump, fans and main power.

Safety: fuse every new feed at the battery and disconnect it before wiring.Low4

Chassis

The RB26 and its turbos add weight over the front axle compared with the KA24DE.

S14 curb weight1,253 kg with the KA24DE2,762 lbSourced · medium4
S14 differentialViscous limited-slip was optional on the base model and SE/LESourced · medium4
Chassis choice

One RB26 build moved from an S13 to an S14 over concern about the older chassis handling the torque

Sourced · medium8

One S14 builder reported concerns about engine weight and weight distribution. Recheck ride height and corner weights after the swap, and uprate front springs if the nose sits low.Medium64

The rear axle takes all the torque now. A viscous limited-slip unit was only optional on the S14, and the documented build fitted a Skyline GT-R limited-slip differential behind its custom driveshaft. Plan differential, half-shaft, clutch and brake upgrades with the engine, not after it.Medium46

Chassis stiffness matters at high torque. One pair of builders moved their planned RB26 project from an S13 to an S14, partly over concern about whether the older chassis could take the load. Inspect seams and mounting points for cracks on any older shell.Medium8

Tuning

The RB26 head is the reason to choose it.

Valvetrain

Shim-over-bucket valvetrain, versus hydraulic lash adjusters on the RB25

Sourced · medium7
Oil pump drive
  • Pre-1992 R32 engines had a narrow crank-to-pump drive that could fail at high rpm
  • Later engines got a wider drive
Sourced · medium23

Its shim-over-bucket valvetrain tolerates more rpm than the RB25's hydraulic lifters, and each cylinder has its own throttle. One magazine notes that for moderate power targets on pump gas, an RB25 does the job for less money.Medium7

Six throttles make idle and light-load fueling sensitive to throttle synchronization and to the load model. Builders who drop the factory airflow meters move to manifold pressure or throttle-angle load, so log lambda, manifold pressure, throttle angle and intake temperature together and refine the fuel table from that data.Low62

Check the oil pump drive before you raise the rev limit. Early R32 engines had a narrow drive collar that could fail at high rpm. Keep ignition advance conservative and guided by knock monitoring and logged results, and raise boost in small steps; no fixed timing figure is safe for every engine and fuel.Medium23

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 23 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Check the law and source the engine
    Confirm import paperwork and registration rules for your region first, then buy a complete RB26 with harness, turbos and intake, and inspect the oil pump drive.
  2. Plan the RWD conversion
    Choose the rear-drive pan route or the cut-and-seal route, source an RB25 five-speed, and order mounts that match that gearbox.
  3. Prepare the engine
    Remove the front differential hardware, fit the rear-drive pan, pickup and dipstick, and replace seals, clutch and flywheel while it is on the stand.
  4. Strip the S14
    Remove the KA24DE, gearbox, driveshaft, radiator and engine harness sections that will not be reused. Label every chassis connector.
  5. Fit mounts and test-fit
    Install the swap brackets on the stock crossmember, lower the engine and gearbox with a load-leveled hoist, and check pan, steering shaft, hood and firewall clearance.
  6. Driveline and shifter
    Measure for the driveshaft at ride height, install it with the shifter and clutch hydraulics, and bleed the clutch.
  7. Cooling, intercooler and fuel
    Mount the radiator, fans and intercooler, connect turbo oil and coolant lines, and install the pump and fuel lines. Pressure-test fuel and cooling.
  8. Wire the engine
    Merge the RB26 harness with S14 power, start, gauge, fan and A/C circuits, mount the controller in the cabin, and fuse every new feed.
  9. First start and calibration
    Prime oil pressure, confirm crank angle sync and fuel pressure, start and check for leaks, then build the calibration from logs at low boost.
  10. Shake down and register
    Re-torque mounts and driveshaft after the first drives, then complete inspection, registration and insurance steps for your region.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Engine will not sit on the mounts or the pan hits the crossmemberThe all-wheel-drive RB26 pan with its front differential housing is still fittedFit a rear-drive pan or have the factory pan cut and sealed, with a matching pickup and dipstick.Medium56
GT-R gearbox will not fit the tunnel or mountsFactory GT-R gearboxes include the ATTESA all-wheel-drive transfer sectionUse a rear-drive RB25DET five-speed and order the transmission mount for it.Medium35
Driveshaft vibration or wrong lengthAn S14 or RB25 car's shaft reused with the new gearbox positionHave a one-piece shaft built to measurement with the engine on its final mounts at ride height.Medium6
Unstable idle and poor light-load fuelingSix throttles out of sync, or the load model does not suit an airflow meter removalSynchronize the throttles, then rebuild the fuel table from wideband and manifold pressure logs.Low26
Loss of oil pressure at high rpm on an early engineNarrow pre-1992 oil pump drive collarInspect the pump drive and fit a later wide-drive pump or an aftermarket collar or spline drive.Medium23
Engine held at the port or car refused at inspectionMissing import declaration, or no certified US configuration to matchFile the EPA declaration at entry and check federal and state emissions rules before buying.Medium91112

Frequently asked

Can you put an RB26 in an S14?

Yes, but it is harder than an RB25 swap. The RB26 only came in all-wheel-drive GT-Rs, so it needs a rear-drive oil pan and a rear-drive RB25 gearbox. RB swap mount kits list RB26 engine mounts for the S14, and builders add a custom driveshaft and a merged harness.Medium563

How do you convert an RB26 to rear-wheel drive?

Remove the front differential hardware by fitting a rear-drive oil pan, or have the factory RB26 pan cut and sealed, with a pickup and dipstick to match. Then bolt on a rear-drive RB25DET five-speed instead of the GT-R gearbox and its transfer section, and have a driveshaft made to fit.Medium563

What transmission do you use for an RB26 240SX?

Most builds use the RB25DET five-speed from a rear-drive Skyline. It shares the RB bellhousing pattern, and S14 swap mount kits offer a transmission mount for it. Factory GT-R gearboxes are built around all-wheel drive, so they do not suit the S14 without major work.Medium563

Is an RB26 swap worth it over an RB25?

It depends on the goal. The RB26 has a shim-over-bucket valvetrain and individual throttles that suit high rpm, while the RB25 uses hydraulic lifters and a single throttle. One magazine notes an RB25 is cheaper to convert and reaches moderate pump-gas power targets without the RB26's extra RWD conversion work.Medium75

Can you import an RB26 engine into the US?

An engine for a car or light truck is declared to US Customs on EPA Form 3520-1, according to EPA's import guidance. Importing it is a separate question from road use: the RB26 was never sold in a US-certified vehicle, so meeting federal and California emissions rules once installed is difficult. This is general information, not legal advice.Medium91011

Is an RB26 swapped S14 street legal?

In the US it is hard to make fully legal, because no certified US configuration of the RB26 exists to match and California's Referee checks against the donor's smog rules. The UK requires a V5C update, Germany an inspector's approval, and Australian states apply VSB 14. This is general information, not legal advice.Medium1112131415

Related

Sources

15 sources
  1. Skyline GT-R (1989: BNR32) · Nissan Motor Co. (Heritage Collection) · oem · retrieved 2026-10-27
  2. Nissan RB engine · Wikipedia · reference · retrieved 2026-10-27
  3. Nissan Skyline GT-R · Wikipedia · reference · retrieved 2026-10-27
  4. Nissan 240SX · Wikipedia · reference · retrieved 2026-10-27
  5. ISR Performance RB Swap Mounts for Nissan 240sx S13/14 · ISR Performance · vendor-doc · retrieved 2026-10-27
  6. Downright Dirty: A 1995 Nissan 240SX with a GT-R RB26DETT swap · Traction Life · press · retrieved 2026-10-27
  7. Triple D 240SX: Drag, Drift, or Drive, This RB-Powered Nissan 240SX Is Ready For Action · DSPORT Magazine · press · retrieved 2026-10-27
  8. Dual 240SX's Rocking RB26DETT Engines · DSPORT Magazine · press · retrieved 2026-10-27
  9. Overview of EPA Import Requirements for Vehicles and Engines (EPA-420-B-11-015, March 2011) · US Environmental Protection Agency · standard · retrieved 2026-10-27
  10. Publications and Forms for Importing Vehicles and Engines · US Environmental Protection Agency · standard · retrieved 2026-10-27
  11. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  12. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  13. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-25
  14. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  15. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25