Nissan · engine family

Nissan RB engine tuning guide

The RB is Nissan's longitudinal inline-six used across the R31 to R34 Skyline, Laurel, Cefiro and Stagea. The performance versions are the 2.0 L RB20DET, the 2.5 L RB25DE/RB25DET (with NVCS intake cam timing, later NEO heads with an on/off VTC solenoid), and the 2.6 L twin-turbo RB26DETT of the GT-R. All DOHC versions use belt-driven cams, Nissan ECCS management with hot-wire air flow meters, an optical camshaft-driven crank angle sensor giving 1 degree and 120 degree signals, six ignition outputs and two knock sensors. Early and R33 engines use low-impedance injectors with a dropping resistor; the R34 RB25DET NEO uses high-resistance injectors.

Reviewed by GAINS editorial team on 2026-11-04.

Generations and variants

VariantYearsLitresCylInductionInjectionCam controlIgnitionSwap demand
RB26DETT1989-022.6I6TTPort injectionnoneCoil-on-plugHigh
RB25DET / NEO1993-022.5I6TPort injectionVTC intake (NEO solid lifters)Coil-on-plugHigh
RB20DET1985-942I6TPort injectionnoneCoil-on-plugMedium
RB30E / RB30ET (VL Commodore)1985-913I6TPort injectionnone (SOHC 12v)DistributorHigh

Variants

Codes, dimensions and years side by side.

CodeDisplacementBore × strokeCompressionYearsApplications
RB20DET (R31, red top)62.0 L78.0 x 69.7 mm8.5:11985-1989R31 Skyline, Z31 Fairlady 200ZR (Japan)NICS dual-runner induction on early engines, ceramic turbine turbo, 270 cc injectors and coil-on-plug ignition per AutoSpeed.
RB20DET (R32, silver top)62.0 L78.0 x 69.7 mm8.5:11989-1993R32 Skyline GTS-t and GTS-4, A31 Cefiro, C33 Laurel158 kW and 264 Nm at 3,200 rpm in R32 form; larger ceramic turbo and revised head versus R31.
RB20DE NEO532.0 L (1,998 cc)78.0 x 69.7 mm9.5:11998-2002R34 Skyline 20GTLean-burn NA engine; 114 kW at 6,400 rpm.
RB25DE722.5 L86.0 x 71.7 mm10.0:11991-1998R32 GTS25, R33 Skyline, C34 Laurel, StageaNVCS on the intake cam from August 1993 (Wikipedia); R33 ECU has a variable valve timing solenoid output.
RB25DET (R33)6272.5 L86.0 x 71.7 mm9.0:11993-1998R33 Skyline GTS25t, WC34 Stagea (to 1998)187 kW at 6,400 rpm and 294 Nm at 4,800 rpm (manual); 370 cc injectors and T28-type ceramic turbo per AutoSpeed. Injectors approx. 1.3 ohm per the R33 manual.
RB25DET NEO6372.5 L86.0 x 71.7 mm9.0:11998-2002R34 Skyline 25GT-t and 25GT-X Four, WC34 Stagea (1998 on)206 kW at 6,400 rpm and 343 Nm at 3,200 rpm per AutoSpeed; ball-bearing turbo; high-resistance injectors, FPCM fuel pump control, turbo pressure sensor and on/off VTC solenoid per the R34 manual.
RB26DETT14562.6 L (2,568 cc)86.0 x 73.7 mm8.5:11989-2002BNR32, BCNR33 and BNR34 Skyline GT-R; Stagea 260RSSix individual throttles, twin parallel ceramic turbos, two hot-wire AFMs. Rated 206 kW (280 PS); torque 353 Nm (R32) rising to 392 Nm (R34).

Valvetrain

Layout

DOHC, 4 valves per cylinder, pent-roof chamber, belt-driven camshafts

Sourced1
RB26DETT followersBucket-type followers with sodium-filled exhaust valvesSourced · medium6
RB25DE/DET (R33) cam timing

Intake cam timing switched by an ECU-driven variable valve timing solenoid (ECU terminal 113)

Sourced2
RB25 NEO VTC

Variable valve timing control solenoid valve, ON/OFF type, at the front of the cylinder head

Sourced3
RB26DETT VVT
  • None
  • The RB26DETT ECU has no valve timing output
Sourced12
Firing order1-5-3-6-2-4Sourced13

RB25 cam timing is a two-position system: the ECU energises a solenoid to change intake cam phase, rather than closed-loop continuous phasing. On a standalone ECU this is a simple on/off output scheduled on rpm and load, and the switch point should be chosen from dyno or logged acceleration data rather than copied between engines.

The RB25 and RB26 share the 86 mm bore and many head dimensions, which is the basis of popular hybrid builds; confirm follower type, cam drive and oiling differences before mixing parts.

Fuel system

Injection

Sequential multi-port ECCS injection, six individual injector outputs

Sourced13
RB26DETT injectors (R32/R33)

Top-feed, approx. 1.3 ohm (low impedance) with a dropping resistor of approx. 4.2 ohm per circuit

Sourced21
RB25DE/DET injectors (R33)Approx. 1.3 ohmlow impedanceSourced2
RB25DET NEO injectors (R34)High-resistance typeSourced3
Injector flow (community/press)
  • RB20DET (R31) 270 cc
  • RB25DET 370 cc
Sourced · medium6
R34 RB25DET NEO fuel pressure
  • 0.25 MPa at idle with regulator vacuum2.5 kg/cm2
  • 0.29 MPa with the vacuum hose removed
Sourced3
Fuel pump control

Fuel pump control modulator (FPCM) varies pump voltage on RB26DETT and RB25DET NEO

R34 manual cites reduced idle noise as the purpose.Sourced132
Regulator

Diaphragm pressure regulator at the fuel rail front end (return system)

Sourced1

Low-impedance RB injectors are fed through a dropping resistor pack, and the ECU has an injector power or counter-electromotive feedback terminal. A standalone ECU must either keep the resistor pack or use peak-and-hold injector drivers; fitting high-impedance injectors removes the need for the resistor.

The FPCM runs the pump at reduced voltage at low load. For higher power builds the pump is often wired for full voltage through a relay, or the FPCM switching is retained but verified under load with fuel pressure logging.

Ignition

R32 RB26DETT

Mini-mould ignition coil above each plug, driven by a separate 6-channel power transistor unit on the rocker cover

Sourced1
R34 RB25DE/DET NEOMicro-mould coil with built-in power transistor on each plugSourced3
ECU ignition outputsSix individual ignition signals (sequential, one per cylinder)Sourced123
Advance control

Electronically controlled ignition advance from ECU maps with knock control

Sourced3

Because the factory ECUs fire each cylinder individually, RBs can run sequential ignition on a standalone without hardware changes, provided the coil type is understood: earlier engines need logic-level drive into an external power transistor unit, while R34-type coils with integrated igniters take a logic-level signal directly. Never drive these inputs with a high-current coil driver.

Crank and cam triggers

Sensor

Crank angle sensor, photoelectric type, driven directly by the camshaft

Sourced13
LocationLeft front of the cylinder headSourced13
Signals

1 degree POS signal and 120 degree REF signal, each wired to two ECU terminals

Sourced123
Signal level

Digital, switching approx. 0 V or 5 V when the shaft is turned by hand with ignition on

Sourced2
RB20DE (L/B) extra sensor

Ring gear crankshaft position sensor (magnetic) on lean-burn RB20DE only

Sourced3

The RB crank angle sensor sits on the cam, so it reports crank position through the timing belt; belt stretch, tensioner condition and cam gear changes move the reference. Verify base timing with a timing light after any belt or cam work. The optical sensor outputs clean 5 V square waves, so a standalone needs Hall/digital inputs, not VR inputs. Some builders replace the cam-driven sensor with a crank trigger for high-rpm accuracy.

Sensors

Air flow meter
  • Hot-wire type
  • Two meters on RB26DETT (front and rear), one on RB25
Sourced123
Intake air temperature
  • Thermistor in the intake collector on RB26DETT
  • No IAT input on the R33 RB25 ECU pin list
Sourced12
Knock sensorsTwo piezoelectric sensors on the block (cylinders 1-3 and 4-6)Sourced123
Oxygen sensors
  • R32 RB26DETT: two heated titanium-type sensors (front and rear)
  • R34: heated zirconia sensor at the turbo outlet
Sourced13
Turbo pressure sensorSilicone diaphragm type on RB25DET NEO (upper rocker cover)Sourced3
Throttle

Variable-resistor throttle sensor plus idle (throttle valve) switch

Sourced13
Coolant temperatureThermistor at the water outletSourced13

The RB26DETT splits airflow across two hot-wire meters that the ECU sums. Upgrading to larger meters or a single meter requires matching changes in the factory calibration, which is a common reason RB26 builds move to a standalone running speed-density with a MAP sensor.

Factory engine management

SystemNissan ECCSElectronically Concentrated Engine Control SystemSourced13
Load strategyHot-wire mass airflow based fuel calculationSourced13
Closed loop
  • Air-fuel ratio feedback control with learning (O2 sensors)
  • R34 adopts SOFIS injection control
Sourced13
Knock control
  • Ignition timing advanced or retarded according to detected knock and fuel type
  • Knock sensor fault retards timing within the knock control range
Sourced3
Pin count
  • R32/R33 ECUs: terminals 1-60 and 101-116
  • R34 ECM(-TCM): 104-pin
Sourced123
DiagnosticsCONSULT data link (RX, TX, CLK, CHK) plus self-diagnosis codesSourced123
Boost control output

Wastegate or boost control solenoid valve driven by the ECU (R32 RB26 terminal 25; R33 RB25DET/RB26 terminal 25; R34 RB25DET terminal 104)

Sourced123

ECCS calculates basic injection from airflow and engine speed, then trims with coolant temperature, start enrichment and O2 feedback. Idle is controlled by an AAC valve, with an air regulator on earlier engines for cold start.

On the R34, the ECM and automatic transmission controller are integrated, and the ECM exchanges torque-reduction requests with the TCS/ABS system over a multiplex line. Replacing the ECU on an R34 automatic therefore affects transmission and traction control, not just the engine.

Timing considerations

Turbo compression
  • 8.5:1RB20DET, RB26DETT
  • About 9.0:1RB25DET
Sourced617
Factory knock strategy

Closed-loop knock retard from two sensors, with fuel-type adaptation

Sourced3

RB turbo engines become knock limited at high load in the mid-rpm range where volumetric efficiency and boost peak together. The RB25DET's higher compression gives better response but less margin than the 8.5:1 RB26DETT on the same fuel and boost.

Ethanol blends and good intercooling raise the knock limit considerably. Develop timing in small steps on a load-bearing dyno, log knock retard from both sensor banks, air temperature and wideband lambda, and keep a margin below the onset of knock. The factory knock system cannot protect a map that is advanced beyond the fuel's limit at sustained high load.

More detail · 1 more paragraph

The cam-driven crank angle sensor means that timing measured with a light must be confirmed after any belt service; a tooth error on the belt shifts the whole ignition map.

Tuning notes

RB26DETT power claims
  • Rated 206 kW across R32-R34
  • AutoSpeed reports independent testing of R32 engines closer to 225 kW and R34 engines near 240 kW
Sourced · medium64
RB25DET NEO ECURevised ECU allows up to about 10 psi boost (AutoSpeed)Sourced · medium6
Factory boost control
  • ECU-controlled boost solenoid
  • R34 RB25DET adds a turbo pressure sensor
Sourced23

Typical upgrade path: boost controller or ECU recalibration, larger injectors (high impedance simplifies drive), fuel pump wired for full voltage, larger AFMs or conversion to MAP-based speed density on a standalone, intercooler and exhaust, then turbo upgrades. Ceramic factory turbine wheels are a known risk once boost is raised.

RB26DETT builds commonly keep the six throttles and run a standalone ECU, using the factory crank angle sensor or a crank trigger, sequential injection and sequential ignition through the factory coil hardware.

Weak points

Ceramic turbine wheels

Factory RB20DET, RB25DET (R33) and RB26DETT turbos use ceramic turbine wheels

Wheel failure at raised boost is widely reported; community consensus.Sourced · medium6
Cam-driven trigger
  • Crank position is read from the camshaft through the belt
  • Belt wear or incorrect installation shifts timing
Sourced · medium13

RB26DETT oil control at sustained high rpm and lateral load is a widely discussed concern in the tuning community, as is the oil pump drive on the crank nose. There is no OEM document here quantifying these limits; treat them as risks to manage with oil pressure logging and proven oiling upgrades.

Common swaps

Common donors
  • RB20DET (R32, Cefiro, Laurel) and RB25DET (R33, Stagea) are common swap engines
  • RB26DETT is rarer and more expensive
Sourced · medium6
Factory manual gearboxes
  • FS5R30A 5-speed behind RB26DETT (R32 GT-R) and RB25DET (R34 25GT-t)
  • FS5W71C behind RB20DER34
Sourced13

RB engines are popular swaps into Nissan S-chassis (S13/S14/S15) and older Datsun/Nissan RWD cars. Requirements typically include engine mounts or crossmember work, sump and steering clearance, a transmission (factory Nissan 5-speeds or adapted aftermarket units), cooling, and a wiring plan.

Wiring options are a donor ECU with a cut-down harness, which works for stock power but must see every input it expects, or a standalone ECU with a new harness. R34 donor ECUs on automatic cars integrate the transmission controller and are harder to reuse.

Vehicles with this engine

GAINS on the Nissan RB

ECU2

ECU2Full sequential fuel and spark for this 6-cylinder, and its electronic throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

What is the RB26 and RB25 firing order?

1-5-3-6-2-4, with cylinder 1 at the front. This is stated in the Nissan R32 GT-R and R34 service manuals.13

What crank trigger does an RB26 use?

A photoelectric crank angle sensor driven by the camshaft at the left front of the head. It outputs a 1 degree POS signal and a 120 degree REF signal as 0-5 V digital pulses.123

Are RB26 injectors high or low impedance?

Low impedance: approx. 1.3 ohm, fed through a dropping resistor of approx. 4.2 ohm per the R33 engine manual. R34 RB25DET NEO injectors are high-resistance.23

What is the RB26DETT compression ratio and bore and stroke?

8.5:1, with 86.0 x 73.7 mm bore and stroke for 2,568 cc.15

What is the difference between an RB25DET and an RB25DET NEO?

The NEO (R34, 1998 on) uses an on/off VTC solenoid, coils with built-in power transistors, high-resistance injectors, FPCM fuel pump control and a turbo pressure sensor. AutoSpeed adds a ball-bearing turbo and 206 kW / 343 Nm versus 187 kW / 294 Nm for the R33 engine.326

Does the RB26DETT have variable cam timing?

No. The RB26DETT ECU pin lists show no valve timing output; NVCS/VTC is an RB25 feature.12

How many air flow meters does an RB26 have?

Two hot-wire air flow meters, front and rear, each wired to its own ECU input and ground.1

How many knock sensors does an RB have?

Two piezoelectric knock sensors on the block, one for cylinders 1-3 and one for cylinders 4-6.12

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Nissan GT-R Model R32 Series Service Manual (sections EN: B1 Engine specifications, B3 ECCS) · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
  2. Nissan R33 Engine Service Manual: RB20E, RB25DE, RB25DET and RB26DETT · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
  3. Nissan Model R34 Series Service Manual (1998), sections GI, EC, SD · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
  4. Nissan Heritage Collection: Skyline GT-R (1989, BNR32) · Nissan Motor Co., Ltd. · oem · retrieved 2026-10-25
  5. Skyline and Skyline GT-R undergo minor model change (press release, August 2000) · Nissan Motor Co., Ltd. · press · retrieved 2026-10-25
  6. The Late-Model Nissan RB Guide (Michael Knowling) · AutoSpeed (Web Publications Pty Ltd), archived copy · press · retrieved 2026-10-25
  7. Nissan RB engine · Wikipedia · community · retrieved 2026-10-25