Nissan · 1998-02

Nissan Skyline 25GT-t R34 RB25DET NEO ECU and tuning guide

The Nissan Skyline 25GT-t R34 RB25DET NEO (1998-02) runs the RB25DET / NEO: 2.5 L I6, turbocharged, port injection, cable throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Factory ECU, pinout and chassis research on this page is shared with Nissan Skyline GT-R R34 RB26DETT.

Years1993-02
Displacement2.5L
LayoutI6
InductionTurbocharged
InjectionPort injection
Cam controlVTC intakeNEO solid lifters
IgnitionCoil-on-plug
Swap demandHigh

Part of the Nissan RB family.

Modeled power and torque

Modelled estimate, not a dyno result.

RB25DET / NEO: stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
010020030040050001002003004001k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (247 hp at 6400 rpm, 217 lb-ft at 4800 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.

RB25DET / NEO data

Platform background

The R34 Skyline (1998-2002) uses NEO-specification RB engines: RB20DE (lean-burn in some versions), RB25DE and the RB25DET NEO in the 25GT-t, plus the RB26DETT in the GT-R. The non-GT-R cars use a 104-pin ECM that integrates the automatic transmission controller and communicates with TCS/ABS over a multiplex line. RB25DET NEO hardware includes coils with built-in power transistors, high-resistance injectors, an on/off VTC solenoid, a turbo pressure sensor and FPCM fuel pump control.

Factory ECU

ECM104-pin digital ECM(-TCM) on the passenger dashboard sideSourced3
RelayECM and ignition coil relay behind the ECMSourced3
Load strategy

Hot-wire MAF with SOFIS injection control and air-fuel feedback learning

Sourced3
Knock control
  • Two knock sensors
  • Timing advanced or retarded to the knock limit for the fuel in use
Sourced3
Boost (RB25DET)

Turbo pressure control solenoid (terminal 104) and turbo pressure sensor (terminal 47)

Sourced3
Fuel pump (RB25DET)FPCM voltage control for reduced idle noise (terminal 111)Sourced3
DiagnosticsCONSULT data link (RX 75, TX 76, CHK 22) and self-diagnosisSourced3

On automatic RB25DET cars the engine ECM also runs the transmission, using select-bit and data-bus signals and the shift, lock-up, line pressure and overrun solenoids. Replacing the ECM on these cars requires a separate transmission controller strategy. Fuel pressure is 0.25 MPa at idle and 0.29 MPa with the regulator vacuum removed.

Factory ECU: harness cross-reference

From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.

Nissan RB25DET NEO ECCS ECU (R34 GT-T / Stagea WC34)Part numbers not yet sourced.
ECU family
Nissan 23710-series ECCS
Applies to
R34 GT-T; Stagea WC34 RB25DET; manual
Not for
automatic; RB25DE NA

No source-supported part number. Forum notes Stagea pin differences: confirm ECU variant.

Low confidenceUnverified
ECCS ECU (RB25DET NEO, R34 Skyline GT-t / ER34)Part numbers not yet sourced.
ECU family
Nissan ECCS, RB25DET NEO (ER34)
Applies to
1999-2002 R34 Skyline 25GT-t, manual; JDM
Not for
automatic (A/T vs M/T ER34 ECUs reported not interchangeable)

No OEM number found from allowed sources. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)

Low confidenceUnverified

Factory ECU pinout

Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.

Nissan Skyline (R34) 104-pin ECM(-TCM), RB20DE / RB25DE / RB25DET NEO

The Nissan Skyline (R34) 104-pin ECM(-TCM), RB20DE / RB25DE / RB25DET NEO uses 1 connector with 104 cavities. This page draws each face from the OEM figure and lists the 88 terminals the OEM table documents, with wire colours where the manual prints them.

1998-2002 · Japan · 1 connector, 104 cavities · 88 terminals sourced

ECM(-TCM) connector, R34 (RB20DE / RB25DE / RB25DET)104 cavities · 88 terminals listed · 104 cavities (101-124 and 1-80) with large cavities (101-124, 4/10/19, 24/25/31/32/42/43, 67/72/80) in three rows and signal cavities in four staggered rows; bolt between the 1-19 and 20-43 groups.

Looking into the harness plug's mating face (mirror of the ECU face).

How the OEM figure is orientedHarness side (looking into the plug), as drawn in the OEM figure. Side confidence: low.
Nissan Skyline (R34) 104-pin ECM(-TCM), RB20DE / RB25DE / RB25DET NEO: ECM(-TCM) connector, R34 (RB20DE / RB25DE / RB25DET)101: Injector No. 1101102: no terminal listed102103: Injector No. 3103104: Variable air intake control solenoid (RB20DE L/B, RB25DE) / turbo pressure control solenoid (RB25DET)104109: Control unit power supply (counter-electromotive current feedback circuit)109110: Injector No. 5110111: Fuel pump terminal voltage control output (RB25DET, to FPCM)111112: Injector No. 6112117: Variable timing control solenoid117118: Heated oxygen sensor heater control118119: Power indicator lamp (RB20DE L/B and RB25DET A/T only)119120: Lock-up solenoid (RB20DE L/B and RB25DET A/T only)120105: Injector No. 2105106: Line pressure solenoid (RB20DE L/B and RB25DET A/T only)106107: Air jet swirl control solenoid (RB20DE L/B)107108: Canister purge control valve108113: Line pressure solenoid, dropping resistor circuit (RB20DE L/B and RB25DET A/T only)113114: Injector No. 4114115: Overrun clutch solenoid (RB20DE L/B and RB25DET A/T only)115116: Injector ground116121: Shift solenoid A (RB20DE L/B and RB25DET A/T only)121122: Shift solenoid B (RB20DE L/B and RB25DET A/T only)122123: no terminal listed123124: Injector ground1241: Ignition signal (power transistor drive) cylinder 112: Ignition signal cylinder 523: Ignition signal cylinder 335: Tachometer drive signal56: no terminal listed67: Ignition signal cylinder 678: Ignition signal cylinder 289: Ignition signal cylinder 4911: AAC valve control1112: no terminal listed1213: Fuel pump relay control1314: Air conditioner relay control1415: no terminal listed1516: no terminal listed1617: Malfunction indicator lamp1718: no terminal listed184: ECM and IGN coil relay control410: no terminal listed1019: no terminal listed1920: Ignition switch START2021: Air conditioner switch2122: Check (diagnosis start) (CHK)2223: Throttle position sensor signal2326: Power steering oil pressure switch2627: no terminal listed2728: SB (select bit) 1 signal (RB25DET A/T)2829: Vehicle speed sensor 2 signal2930: Headlamp switch3033: Idle position switch (RB20DE L/B and RB25DET A/T only)3334: '1' position switch (RB20DE L/B and RB25DET A/T only)3435: '2' position switch (RB20DE L/B and RB25DET A/T only)3536: no terminal listed3637: Throttle opening signal (RB25DE 4WD M/T, RB25DE A/T, RB25DET)3738: 'D' position switch (RB20DE L/B and RB25DET A/T only)3839: Neutral signal (park/neutral position switch)3940: 'R' position switch (RB20DE L/B and RB25DET A/T only)4041: Full switch (RB20DE L/B and RB25DET A/T only)4124: Ignition switch (IGN)2425: Control unit ground2531: Ignition power supply3132: Control unit ground3242: no terminal listed4243: Sensor ground4344: Crank angle sensor 120 degree (REF)4445: Crank angle sensor 120 degree (REF)4546: Crank angle sensor 1 degree (POS)4647: Ring gear crankshaft position sensor (RB20DE L/B) / turbo pressure sensor (RB25DET)4764: A/T mode switch POWER (RB20DE L/B A/T)6465: DB (data bus) 1 (RB25DET A/T)6566: DB (data bus) 3 (RB25DET A/T)6648: 5 V supply for throttle position sensor, refrigerant pressure sensor and turbo pressure sensor4849: Rear defogger switch4950: Heated oxygen sensor5051: Throttle motor sensor (RB25DET)5152: SB (select bit) 2 signal (RB25DET A/T)5253: Motor throttle switch (RB25DET)5368: O/D OFF indicator lamp (RB20DE L/B and RB25DET A/T only)6869: DB (data bus) 2 (RB25DET A/T)6970: A/T mode switch SNOW (RB20DE L/B A/T)7071: Stop lamp switch (RB20DE L/B and RB25DET A/T only)7154: Mass air flow sensor signal5455: Mass air flow sensor ground5556: Engine coolant temperature sensor5657: Refrigerant pressure sensor5758: Output shaft rotation sensor (vehicle speed sensor 1) (RB20DE L/B and RB25DET A/T only)5873: no terminal listed7374: no terminal listed7475: CONSULT receive (RX)7576: CONSULT transmit (TX)7659: Turbine sensor (RB25DET A/T)5960: A/T oil temperature sensor (RB20DE L/B and RB25DET A/T only)6061: no terminal listed6162: Knock sensor 16263: Knock sensor 26377: no terminal listed7778: Auxiliary electric fan relay control (RB25DE, RB25DET)7879: ECM-TCM, TCS/ABS integrated control multiplex communication (RB25DE A/T, RB25DET)7967: Control unit power supply6772: Control unit power7280: Battery power supply80
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Ignition signal (power transistor drive) cylinder 1Ignition—
2Ignition signal cylinder 5Ignition—
3Ignition signal cylinder 3Ignition—
4ECM and IGN coil relay controlOutputs—
5Tachometer drive signalComms / diag—
7Ignition signal cylinder 6Ignition—
8Ignition signal cylinder 2Ignition—
9Ignition signal cylinder 4Ignition—
11AAC valve controlOutputs—
13Fuel pump relay controlOutputs—
14Air conditioner relay controlOutputs—
17Malfunction indicator lampComms / diag—
20Ignition switch STARTSensor signal—
21Air conditioner switchSensor signal—
22Check (diagnosis start) (CHK)Comms / diag—
23Throttle position sensor signalSensor signal—
24Ignition switch (IGN)Power—
25Control unit groundGround—
26Power steering oil pressure switchSensor signal—
28SB (select bit) 1 signal (RB25DET A/T)Sensor signal—
29Vehicle speed sensor 2 signalSensor signal—
30Headlamp switchSensor signal—
31Ignition power supplyPower—
32Control unit groundGround—
33Idle position switch (RB20DE L/B and RB25DET A/T only)Sensor signal—
34'1' position switch (RB20DE L/B and RB25DET A/T only)Sensor signal—
35'2' position switch (RB20DE L/B and RB25DET A/T only)Sensor signal—
37Throttle opening signal (RB25DE 4WD M/T, RB25DE A/T, RB25DET)Sensor signal—
38'D' position switch (RB20DE L/B and RB25DET A/T only)Sensor signal—
39Neutral signal (park/neutral position switch)Sensor signal—
40'R' position switch (RB20DE L/B and RB25DET A/T only)Sensor signal—
41Full switch (RB20DE L/B and RB25DET A/T only)Sensor signal—
43Sensor groundSensor 5 V / ground—
44Crank angle sensor 120 degree (REF)Crank / cam—
45Crank angle sensor 120 degree (REF)Crank / cam—
46Crank angle sensor 1 degree (POS)Crank / cam—
47Ring gear crankshaft position sensor (RB20DE L/B) / turbo pressure sensor (RB25DET)Crank / cam—
485 V supply for throttle position sensor, refrigerant pressure sensor and turbo pressure sensorSensor 5 V / ground—
49Rear defogger switchSensor signal—
50Heated oxygen sensorSensor signal—
51Throttle motor sensor (RB25DET)Sensor signal—
52SB (select bit) 2 signal (RB25DET A/T)Sensor signal—
53Motor throttle switch (RB25DET)Sensor signal—
54Mass air flow sensor signalSensor signal—
55Mass air flow sensor groundSensor 5 V / ground—
56Engine coolant temperature sensorSensor signal—
57Refrigerant pressure sensorSensor signal—
58Output shaft rotation sensor (vehicle speed sensor 1) (RB20DE L/B and RB25DET A/T only)Sensor signal—
59Turbine sensor (RB25DET A/T)Sensor signal—
60A/T oil temperature sensor (RB20DE L/B and RB25DET A/T only)Sensor signal—
62Knock sensor 1Sensor signal—
63Knock sensor 2Sensor signal—
64A/T mode switch POWER (RB20DE L/B A/T)Sensor signal—
65DB (data bus) 1 (RB25DET A/T)Comms / diag—
66DB (data bus) 3 (RB25DET A/T)Comms / diag—
67Control unit power supplyPower—
68O/D OFF indicator lamp (RB20DE L/B and RB25DET A/T only)Outputs—
69DB (data bus) 2 (RB25DET A/T)Comms / diag—
70A/T mode switch SNOW (RB20DE L/B A/T)Sensor signal—
71Stop lamp switch (RB20DE L/B and RB25DET A/T only)Sensor signal—
72Control unit powerPower—
75CONSULT receive (RX)Comms / diag—
76CONSULT transmit (TX)Comms / diag—
78Auxiliary electric fan relay control (RB25DE, RB25DET)Outputs—
79ECM-TCM, TCS/ABS integrated control multiplex communication (RB25DE A/T, RB25DET)Comms / diag—
80Battery power supplyPower—
101Injector No. 1Injector—
103Injector No. 3Injector—
104Variable air intake control solenoid (RB20DE L/B, RB25DE) / turbo pressure control solenoid (RB25DET)Outputs—
105Injector No. 2Injector—
106Line pressure solenoid (RB20DE L/B and RB25DET A/T only)Outputs—
107Air jet swirl control solenoid (RB20DE L/B)Outputs—
108Canister purge control valveOutputs—
109Control unit power supply (counter-electromotive current feedback circuit)Power—
110Injector No. 5Injector—
111Fuel pump terminal voltage control output (RB25DET, to FPCM)Outputs—
112Injector No. 6Injector—
113Line pressure solenoid, dropping resistor circuit (RB20DE L/B and RB25DET A/T only)Outputs—
114Injector No. 4Injector—
115Overrun clutch solenoid (RB20DE L/B and RB25DET A/T only)Outputs—
116Injector groundGround—
117Variable timing control solenoidOutputs—
118Heated oxygen sensor heater controlOutputs—
119Power indicator lamp (RB20DE L/B and RB25DET A/T only)Outputs—
120Lock-up solenoid (RB20DE L/B and RB25DET A/T only)Outputs—
121Shift solenoid A (RB20DE L/B and RB25DET A/T only)Outputs—
122Shift solenoid B (RB20DE L/B and RB25DET A/T only)Outputs—
124Injector groundGround—

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (low confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

Covers the R34 104-pin ECM(-TCM) used with RB20DE, RB25DE and RB25DET NEO. The R34 GT-R (RB26DETT) ECU is a different unit and is not covered.

Source notes: From the Nissan Model R34 Series Service Manual (1998), 'ECM(-TCM) Terminal Layout' (EC-13/14). Terminals not listed are shown as unused. Items marked as RB20DE L/B and RB25DET A/T only follow the manual's asterisk note. Wire colours are not given in this table. The R34 GT-R (RB26DETT) ECU pinout is not covered by this manual.

Safety: disconnect the battery before working on the ECU harness, and confirm each terminal with a meter against your own car's manual before cutting or pinning wires.

All factory ECU pinouts →

Plug-and-play harness

Route for this carS3 plug-in harness
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.

MakerHarnessFitsLink
Nissan Skyline R34 GT-THT-186363R34 GT-T; Stagea WC34 RB25DET; manual$535LowestMaker ↗
Manual 1999 - 2002 Nissan Skyline RB25DET NEOBF29132-S31999-2002 R34 Skyline 25GT-t, manual; JDM$840Maker ↗
Wire-inUniversal flying lead or re-terminated factory harnessAny engine (terminate to ECU2's two Superseal 34 connectors)Universal harness from $405Maker ↗

Nexus S3 Plug n Play Adapter Harness Nissan Skyline R34 GT-T

$535USD list · excl. tax
Plug-and-playManual onlyOff-road / competition onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Nissan RB25DET NEO ECCS ECU (R34 GT-T / Stagea WC34)
ECU
Nissan 23710-series ECCS
Confidence
low

No source-supported part number. Forum notes Stagea pin differences: confirm ECU variant.

Fits
R34 GT-T; Stagea WC34 RB25DET; manual
Exclusions
automatic; RB25DE NA
SKU
HT-186363
Maker fitment
Nissan Skyline R34 GT-T and Stagea WC34; manual only
Maker notes
kit HT-213309

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1999 - 2002 Nissan Skyline RB25DET NEO

$840USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
ECCS ECU (RB25DET NEO, R34 Skyline GT-t / ER34)
ECU
Nissan ECCS, RB25DET NEO (ER34)
Confidence
low

No OEM number found from allowed sources. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)

Fits
1999-2002 R34 Skyline 25GT-t, manual; JDM
Exclusions
automatic (A/T vs M/T ER34 ECUs reported not interchangeable)
SKU
BF29132-S3
Maker fitment
Nissan Skyline RB25DET NEO (Manual); selector years 1999-2002; SKU label: Manual 1999 - 2002 Nissan Skyline RB25DET NEO
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2)

Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.

Your GAINS system for this car · pre-release

ECU2 for the Skyline 25GT-t R34

Planned with the same rules as the configurator for this car's 6 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

  • ECU2Engine controller

    6 cyl · port injection · cable throttle

    Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harness1 listed · from $535 USD listHT-186363
  2. Factory-connector → S3 adapter1 listed · from $840 USD list
  3. Wire-inAlways possible

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Skyline 25GT-t R34

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Cam phasing (VVT)gated

    Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.

  4. 4
    Boost controlgated

    A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.

  5. 5
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  6. 6
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAF (hot-wire / hot-film) (medium confidence)

  7. 7
    Wideband sensorhardware

    Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller

  8. 8
    Bottom end and head sealingfactory reference

    Reported: Stock oil pump commonly reported to break at high rpm (~8,000 rpm per a builder on SAU forum); stock turbo boost limit around 10 psi often cited (forum). (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Drivetrain

25GT Turbo manualFS5R30A 5-speed manual, R200V rear differentialSourced3
25GT Turbo automaticRE4R01B 4-speed automatic, R200V rear differentialSourced3
20GT

FS5W71C 5-speed manual or RE4R01B automatic, R200 rear differential

Sourced3
GT-RRB26DETT with 6-speed manual and 4WDSourced2
SteeringElectric Super HICAS on designated 2WD variantsSourced · medium3

Chassis integration

Engine-TCS/ABS integration

Torque reduction during shifts and TCS intervention via multiplex communication between ECM-TCM and TCS/ABS

Sourced3
Throttle motor

Throttle motor sensor (51) and motor throttle switch (53) inputs on RB25DET

Sourced3
Cooling

Auxiliary electric fan relay (78) switched on coolant temperature and A/C signal

Sourced3
A/C
  • Refrigerant pressure sensor input (57) and A/C relay output (14)
  • A/C cut at start and during acceleration
Sourced3
TachometerTachometer drive signal at terminal 5Sourced3

Removing the factory ECM affects traction control, which relies on multiplex communication with the engine ECM and a motor-driven throttle input on RB25DET cars. Plan to either retain TCS integration or disable it cleanly, and recreate the auxiliary fan and A/C pressure logic in the replacement ECU.

Tuning notes

RB25DET NEO output206 kW at 6,400 rpm, 343 Nm at 3,200 rpmSourced · medium1
InjectorsHigh-resistance typeSourced3
Fuel pressure

0.25 MPa at idle with vacuum, 0.29 MPa with regulator vacuum removed

Sourced3
GT-R RB26DETT

2,568 cc, 86.0 x 73.7 mm, 8.5:1, 206 kW at 6,800 rpm, 392 Nm at 4,400 rpm

Sourced2

The RB25DET NEO responds well to boost and fuel upgrades; high-impedance injectors make injector swaps simpler than on R33. Log the turbo pressure sensor and both knock channels when changing boost targets, and retune VTC switching with any cam or turbo change.

Popular swaps

NEO engines

RB25DET NEO also fitted to the second-generation Stagea (1998 on)

Sourced · medium1

RB25DET NEO engines are popular swap units. Because the R34 ECM integrates the automatic transmission controller, manual-gearbox donor ECUs or standalone ECUs are simpler for swaps.

GAINS on the Skyline 25GT-t R34

ECU2

ECU2Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

How many pins does the R34 ECU have?

The R34 ECM(-TCM) is a 104-pin unit (terminals 1-80 and 101-124).3

Which R34 ECU pin controls the RB25 NEO VTC solenoid?

Terminal 117, variable timing control solenoid.3

Which R34 ECU pins are the crank angle sensor?

120 degree REF on terminals 44 and 45, 1 degree POS on 46.3

Does the R34 RB25DET have a boost sensor?

Yes, a turbo pressure sensor on terminal 47, powered from the 5 V supply on terminal 48.3

What gearbox is in the R34 25GT-t?

FS5R30A 5-speed manual or RE4R01B 4-speed automatic, with an R200V rear differential.3

Are R34 RB25DET injectors high impedance?

Yes. Nissan lists them as high-resistance injectors.3

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. The Late-Model Nissan RB Guide (Michael Knowling) · AutoSpeed (Web Publications Pty Ltd), archived copy · press · retrieved 2026-10-25
  2. Skyline and Skyline GT-R undergo minor model change (press release, August 2000) · Nissan Motor Co., Ltd. · press · retrieved 2026-10-25
  3. Nissan Model R34 Series Service Manual (1998), sections GI, EC, SD · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  1. E-926 Haltech S3 adapter harness page (sourced, high confidence)
  2. E-934 Boomslang identity (sourced, high confidence)
  3. E-935 Boomslang S3 catalog size (sourced, high confidence)
  4. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  5. E-941 S3 engine harness availability (inferred, medium confidence)