Nissan · 1989-94

Nissan Skyline GTS-t R32 RB20DET ECU and tuning guide

The Nissan Skyline GTS-t R32 RB20DET (1989-94) runs the RB20DET: 2 L I6, turbocharged, port injection, cable throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Factory ECU, pinout and chassis research on this page is shared with Nissan Skyline GT-R R32 RB26DETT.

Engine: RB20DET

Years1985-94
Displacement2L
LayoutI6
InductionTurbocharged
InjectionPort injection
Cam controlnone
IgnitionCoil-on-plug
Swap demandMedium

Part of the Nissan RB family.

Modeled power and torque

Modelled estimate, not a dyno result.

RB20DET: stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
010020030040001002003004001k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (212 hp at 6400 rpm, 195 lb-ft at 3200 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.

RB20DET data

Platform background

The R32 Skyline (1989-1994) brought back the GT-R with the 2,568 cc RB26DETT, twin parallel turbos, six throttles, two hot-wire air flow meters and ATTESA E-TS four-wheel drive, while the GTS-t and GTS-4 used the 2.0 L RB20DET. This page gives the Nissan factory ECCS control unit pinout for the BNR32 RB26DETT from the R32 GT-R service manual.

Factory ECU

System
  • Nissan ECCS
  • Control unit behind the left-hand dash side lower finisher (GT-R)
Sourced3
Terminals

Terminals 1-60 (signal) and 101-116 (injector/power), with CONSULT RX, TX, CLK, CHK and IGN pins

Sourced3
Air meteringTwo hot-wire air flow metersfront and rearSourced3
Trigger
  • Photoelectric crank angle sensor driven by the camshaft, left front of cylinder head
  • 1 degree and 120 degree signals
Sourced3
Ignition
  • Six ignition signals to a separate 6-channel power transistor unit
  • Mini-mould coil above each plug
Sourced3
Fuel pumpFuel pump control modulator (FPCM) driven by two ECU outputsSourced3
Boost controlECU-driven wastegate valve control solenoidSourced3
DiagnosticsCONSULT data link and on-board self-diagnosis modesSourced3

The R32 GT-R ECU sums two airflow meters, so modifications to either intake side change the fuel calculation. It provides individual ignition and injection per cylinder, two knock channels, closed-loop O2 control on both banks, and pre-dates OBD-II standards.

Factory ECU: harness cross-reference

From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.

Nissan RB ECCS ECU (R32/R33 GTS-t, R32/R33/R34 GT-R)
23710-05U0223710-05U6023710-05U6123710-05U62
ECU family
Nissan 23710-series ECCS
Applies to
R32 GTS-t, R32 GT-R, R33 GTS-t, R33 GT-R, R34 GT-R; manual
Not for
R34 GT-T (use HT-186363); automatic
Supplier
Hitachi

Only R32 GT-R (RB26DETT) numbers sourced, with production-date split per forum citing Nissan parts. R32/R33 GTS-t and R33/R34 GT-R numbers not gathered; one harness spans several ECU generations.

Sourced · mediumE-1451
ECCS ECU (RB20DET, R32 Skyline GTS-t)Part numbers not yet sourced.
ECU family
Nissan ECCS, RB20DET (HCR32)
Applies to
1989-1994 R32 Skyline GTS-t RB20DET, manual; JDM
Not for
automatic

No OEM number found from allowed sources. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)

Low confidenceUnverified

Factory ECU pinout: pending

No OEM pin table is in our library yet for the RB20DET factory ECU. From the Nissan GT-R Model R32 Series Service Manual, 'ECCS control unit pin layout figure: RB26DETT' (EN-171/172). Unlisted terminals (5, 8, 14, 15, 17, 33, 37, 39, 40, 102, 111, 113, 115) are shown as unused for this engine. Wire colours are not given in that table. The R32 GTS-t/GTS-4 RB20DET ECU pinout was not obtained; it needs the R32 (non-GT-R) service manual ECCS section. Until then, wire from the harness maker's instructions or the factory service manual.

Factory ECU pinout

The researched pinout on file is for ECCS control unit (BNR32, RB26DETT), which is a different ECU from this RB20DET variant. From the Nissan GT-R Model R32 Series Service Manual, 'ECCS control unit pin layout figure: RB26DETT' (EN-171/172). Unlisted terminals (5, 8, 14, 15, 17, 33, 37, 39, 40, 102, 111, 113, 115) are shown as unused for this engine. Wire colours are not given in that table. The R32 GTS-t/GTS-4 RB20DET ECU pinout was not obtained; it needs the R32 (non-GT-R) service manual ECCS section.

Plug-and-play harness

Route for this carS3 plug-in harness
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.

MakerHarnessFitsLink
Nissan Skyline R32/R33/R34 GT-RHT-186362R32 GTS-t, R32 GT-R, R33 GTS-t, R33 GT-R, R34 GT-R; manual$535LowestMaker ↗
Manual 1989 - 1994 Nissan Skyline RB20DETBF29096-S31989-1994 R32 Skyline GTS-t RB20DET, manual; JDM$840Maker ↗
Wire-inUniversal flying lead or re-terminated factory harnessAny engine (terminate to ECU2's two Superseal 34 connectors)Universal harness from $405Maker ↗

Nexus S3 Plug n Play Adapter Harness Nissan Skyline R32/R33/R34 GT-R

$535USD list · excl. tax
Plug-and-playManual onlyOff-road / competition onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Nissan RB ECCS ECU (R32/R33 GTS-t, R32/R33/R34 GT-R) · 23710-05U02, 23710-05U60…
OEM part numbers
23710-05U02, 23710-05U60, 23710-05U61, 23710-05U62
ECU
Hitachi · Nissan 23710-series ECCS
Confidence
medium

Only R32 GT-R (RB26DETT) numbers sourced, with production-date split per forum citing Nissan parts. R32/R33 GTS-t and R33/R34 GT-R numbers not gathered; one harness spans several ECU generations.

Sources: E-1451

Fits
R32 GTS-t, R32 GT-R, R33 GTS-t, R33 GT-R, R34 GT-R; manual
Exclusions
R34 GT-T (use HT-186363); automatic
SKU
HT-186362
Maker fitment
Nissan Skyline R32 GTS-T, R32 GT-R, R33 GTS-T, R33 GT-R, R34 GT-R; manual only (kit page)
Maker notes
kit HT-213320 USD 2800

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1989 - 1994 Nissan Skyline RB20DET

$840USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
ECCS ECU (RB20DET, R32 Skyline GTS-t)
ECU
Nissan ECCS, RB20DET (HCR32)
Confidence
low

No OEM number found from allowed sources. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)

Fits
1989-1994 R32 Skyline GTS-t RB20DET, manual; JDM
Exclusions
automatic
SKU
BF29096-S3
Maker fitment
Nissan Skyline RB20DET (Manual); selector years 1989-1994; SKU label: Manual 1989 - 1994 Nissan Skyline RB20DET
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2)

Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.

Your GAINS system for this car · pre-release

ECU2 for the Skyline GTS-t R32

Planned with the same rules as the configurator for this car's 6 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

  • ECU2Engine controller

    6 cyl · port injection · cable throttle

    Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harness1 listed · from $535 USD listHT-186362
  2. Factory-connector → S3 adapter1 listed · from $840 USD list
  3. Wire-inAlways possible

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Skyline GTS-t R32

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Boost controlgated

    A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.

  4. 4
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  5. 5
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAF (hot-wire / hot-film) (medium confidence)

  6. 6
    Wideband sensorhardware

    Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller

Drivetrain

GT-R transmissionFS5R30A 5-speed manualSourced32
GT-R drive system

ATTESA E-TS electronically controlled torque-split four-wheel drive

Sourced2
GTS-t / GTS-4
  • RB20DET with 5-speed manual or 4-speed automatic
  • GTS-4 is AWD
Sourced · medium1

Chassis integration

TachometerTachometer driven from ECU terminal 7Sourced3
Vehicle speedVehicle speed sensor input at terminal 53Sourced3
A/CA/C switch input (46) and A/C relay output (9) for A/C cutSourced3
CoolingSub electric fan relay output6Sourced3
Exhaust temperature warning

Thermocouple-type exhaust temperature warning equipment, set at 850 C

Sourced3
Four-wheel steeringHICAS rear steer system referenced throughout the GT-R manualSourced · medium3

ATTESA E-TS and HICAS have their own controllers; a standalone engine ECU must still supply the vehicle speed and throttle information those systems expect where they are wired from the engine side. Check the chassis wiring diagram before deleting the factory throttle opening output (terminal 38).

Tuning notes

EngineRB26DETT, 2,568 cc, 86.0 x 73.7 mm, 8.5:1Sourced3
Rated output206 kW at 6,800 rpm, 353 Nm at 4,400 rpm280 PSSourced2
InjectorsLow impedance (approx. 1.3 ohm) with a dropping resistorSourced4
Real-world output

AutoSpeed reports the R32 RB26DETT closer to about 225 kW than the rated figure

Sourced · medium1

Common R32 GT-R steps are boost increase via the wastegate solenoid control, fuel pump upgrade (with FPCM retained or bypassed), larger air flow meters or a standalone ECU with MAP-based load, and turbo upgrades to replace the ceramic-wheel factory units. Log both knock channels and per-bank lambda during development.

Popular swaps

Silver-top RB20DET
  • R32-spec RB20DET also fitted to Cefiro and Laurel
  • Popular for conversions
Sourced · medium1

RB25DET and RB26DETT conversions into GTS-t/GTS-4 bodies are common. A wiring plan is required because the RB26 ECU expects two airflow meters, FPCM fuel pump control and GT-R-specific inputs.

GAINS on the Skyline GTS-t R32

ECU2

ECU2Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

Where is the ECU in an R32 GT-R?

Inside the left-hand dash side lower finisher, per the R32 GT-R service manual.3

What are the R32 GT-R crank angle sensor pins?

120 degree signals on terminals 41 and 51, 1 degree signals on 42 and 52.3

Which R32 GT-R ECU pins are the injectors?

101 (No.1), 105 (No.2), 103 (No.3), 114 (No.4), 110 (No.5), 112 (No.6), with injector grounds on 107, 108 and 116.3

How many air flow meters does the R32 GT-R have?

Two hot-wire meters, front (signal 35, ground 34) and rear (signal 27, ground 26).3

What gearbox does the R32 GT-R use?

The FS5R30A 5-speed manual, driving through ATTESA E-TS four-wheel drive.32

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. The Late-Model Nissan RB Guide (Michael Knowling) · AutoSpeed (Web Publications Pty Ltd), archived copy · press · retrieved 2026-10-25
  2. Nissan Heritage Collection: Skyline GT-R (1989, BNR32) · Nissan Motor Co., Ltd. · oem · retrieved 2026-10-25
  3. Nissan GT-R Model R32 Series Service Manual (sections GI, EN: B1 Engine specifications, B3 ECCS) · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
  4. Nissan R33 Engine Service Manual: RB20E, RB25DE, RB25DET and RB26DETT · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  1. E-925 Haltech S3 adapter harness page (sourced, high confidence)
  2. E-934 Boomslang identity (sourced, high confidence)
  3. E-935 Boomslang S3 catalog size (sourced, high confidence)
  4. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  5. E-941 S3 engine harness availability (inferred, medium confidence)
  6. E-1451 R32 GT-R ECU (supported, medium confidence)