Nissan · 1993-98

Nissan Skyline GTS-t R33 RB25DET ECU and tuning guide

The Nissan Skyline GTS-t R33 RB25DET (1993-98) runs the RB25DET / NEO: 2.5 L I6, turbocharged, port injection, cable throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Factory ECU, pinout and chassis research on this page is shared with Nissan Skyline GT-R R33 RB26DETT.

Years1993-02
Displacement2.5L
LayoutI6
InductionTurbocharged
InjectionPort injection
Cam controlVTC intakeNEO solid lifters
IgnitionCoil-on-plug
Swap demandHigh

Part of the Nissan RB family.

Modeled power and torque

Modelled estimate, not a dyno result.

RB25DET / NEO: stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
010020030040050001002003004001k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (247 hp at 6400 rpm, 217 lb-ft at 4800 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.

RB25DET / NEO data

Platform background

The R33 Skyline (1993-1998) introduced the RB25DET (86 x 71.7 mm, intake cam timing solenoid, ECU-controlled boost solenoid) in the GTS25t, with the RB25DE in NA models and the RB26DETT carried over in the GT-R. This page gives the Nissan factory ECCS control unit pin layout for the RB25DE/RB25DET from the R33 engine service manual.

Factory ECU

SystemNissan ECCS, MAF (hot-wire) basedSourced2
TerminalsTerminals 1-60 and 101-116 with CONSULT RX, TX, CLK, CHK, IGNSourced2
Cam timingVariable valve timing solenoid output (terminal 113)Sourced2
BoostBoost control solenoid outputterminal 25, RB25DETSourced2
Fuel pumpFPCM fuel pump voltage control output on RB25DET (terminal 104)Sourced2
A/T interface

Engine-A/T control signals DT1-DT3 to the automatic transmission controller

Sourced2
InjectorsLow impedance, approx. 1.3 ohmSourced2

The RB25 ECU has a single airflow meter and no intake air temperature input in its pin list, so charge temperature compensation is limited compared with later ECUs. Diagnosis is by self-diagnosis codes and CONSULT.

Factory ECU: harness cross-reference

From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.

Nissan RB ECCS ECU (R32/R33 GTS-t, R32/R33/R34 GT-R)
23710-05U0223710-05U6023710-05U6123710-05U62
ECU family
Nissan 23710-series ECCS
Applies to
R32 GTS-t, R32 GT-R, R33 GTS-t, R33 GT-R, R34 GT-R; manual
Not for
R34 GT-T (use HT-186363); automatic
Supplier
Hitachi

Only R32 GT-R (RB26DETT) numbers sourced, with production-date split per forum citing Nissan parts. R32/R33 GTS-t and R33/R34 GT-R numbers not gathered; one harness spans several ECU generations.

Sourced · mediumE-1451
ECCS ECU (RB25DET, R33 Skyline GTS-t)
23710-21U0023710-21U0123710-13U00
ECU family
Nissan ECCS, RB25DET (ECR33)
Applies to
1993-1998 R33 Skyline GTS-25t, manual; JDM
Not for
R34 RB25DET NEO uses BF29132-S3; automatic

Forum/resale only: 21U00 and 21U01 described as R33 RB25DET; 13U00 described by a seller as R33 Series 2 manual. Series 1 vs Series 2 ECUs differ (immobiliser on S2 reported). blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)

Low confidenceUnverifiedE-1489

Factory ECU pinout

Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.

Nissan Skyline (R33) RB25DE / RB25DET ECCS control unit

The Nissan Skyline (R33) RB25DE / RB25DET ECCS control unit uses 1 connector with 76 cavities. This page draws each face from the OEM figure and lists the 63 terminals the OEM table documents, with wire colours where the manual prints them.

1993-1998 · Japan · 1 connector, 76 cavities · 63 terminals sourced

ECCS control unit connector, R33 (RB25DE / RB25DET)76 cavities · 63 terminals listed · 76 cavities in two rows: 101-108/109-116, 1-10/11-20, centre bolt, 21-30/31-40, 41-50/51-60; all numbers legible in the OEM figure.

Looking into the harness plug's mating face (mirror of the ECU face).

How the OEM figure is orientedHarness side (looking into the plug), as drawn in the OEM figure. Side confidence: low.
Nissan Skyline (R33) RB25DE / RB25DET ECCS control unit: ECCS control unit connector, R33 (RB25DE / RB25DET)101: Injector No. 1101102: no terminal listed102103: Injector No. 3103104: Fuel pump terminal power control output to FPCM (RB25DET only)104105: Injector No. 2105106: no terminal listed106107: Injector ground107108: Injector ground1081: Ignition signal to power transistor, cylinder 112: Ignition signal, cylinder 523: Ignition signal, cylinder 334: AAC valve control45: Engine-A/T control input DT1 (A/T)56: no terminal listed67: Engine rev signal for tachometer78: no terminal listed89: Air conditioner relay (A/C cut)910: Earth (ignition signal system)1021: CONSULT receive (RX)2122: CONSULT transmit (TX)2223: Knock sensor 1 (cylinders 1-3)2324: Knock sensor 2 (cylinders 4-6)2425: Boost control solenoid (RB25DET only)2526: Air flow meter earth2627: Air flow meter signal2728: Engine coolant temperature sensor2829: Exhaust gas (O2) sensor2930: Earth (sensor signal system)3041: Crank angle sensor 120 degree (REF)4142: Crank angle sensor 1 degree (POS)4243: Key switch START4344: Neutral switch4445: Key switch IGN (IGN)4546: Air conditioner switch4647: Check (diagnosis) (CHK)4748: Throttle sensor power4849: Control unit power4950: Control unit earth50109: Inverse current feedback circuit109110: Injector No. 5110111: no terminal listed111112: Injector No. 6112113: Variable valve timing solenoid113114: Injector No. 4114115: Exhaust gas sensor heater ground115116: Injector ground11611: Ignition signal, cylinder 61112: Ignition signal, cylinder 21213: Ignition signal, cylinder 41314: Engine-A/T control input DT2 (A/T)1415: Engine-A/T control input DT3 (A/T)1516: ECCS relay1617: Injection pulse (Ti monitor) signal1718: Fuel pump relay1819: Power steering oil pressure switch1920: Earth (ignition signal system)2031: CONSULT clock (CLK)3132: Engine warning lamp3233: Exhaust temperature warning lamp3334: no terminal listed3435: no terminal listed3536: no terminal listed3637: no terminal listed3738: Throttle sensor opening signal3839: no terminal listed3940: no terminal listed4051: Crank angle sensor 120 degree (REF)5152: Crank angle sensor 1 degree (POS)5253: Vehicle speed sensor5354: no terminal listed5455: no terminal listed5556: Throttle opening output signal5657: Exhaust temperature sensor5758: Battery power5859: Control unit power5960: Control unit earth (-)60
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Ignition signal to power transistor, cylinder 1Ignition—
2Ignition signal, cylinder 5Ignition—
3Ignition signal, cylinder 3Ignition—
4AAC valve controlOutputs—
5Engine-A/T control input DT1 (A/T)Comms / diag—
7Engine rev signal for tachometerComms / diag—
9Air conditioner relay (A/C cut)Outputs—
10Earth (ignition signal system)Ground—
11Ignition signal, cylinder 6Ignition—
12Ignition signal, cylinder 2Ignition—
13Ignition signal, cylinder 4Ignition—
14Engine-A/T control input DT2 (A/T)Comms / diag—
15Engine-A/T control input DT3 (A/T)Comms / diag—
16ECCS relayOutputs—
17Injection pulse (Ti monitor) signalComms / diag—
18Fuel pump relayOutputs—
19Power steering oil pressure switchSensor signal—
20Earth (ignition signal system)Ground—
21CONSULT receive (RX)Comms / diag—
22CONSULT transmit (TX)Comms / diag—
23Knock sensor 1 (cylinders 1-3)Sensor signal—
24Knock sensor 2 (cylinders 4-6)Sensor signal—
25Boost control solenoid (RB25DET only)Outputs—
26Air flow meter earthSensor 5 V / ground—
27Air flow meter signalSensor signal—
28Engine coolant temperature sensorSensor signal—
29Exhaust gas (O2) sensorSensor signal—
30Earth (sensor signal system)Sensor 5 V / ground—
31CONSULT clock (CLK)Comms / diag—
32Engine warning lampOutputs—
33Exhaust temperature warning lampOutputs—
38Throttle sensor opening signalSensor signal—
41Crank angle sensor 120 degree (REF)Crank / cam—
42Crank angle sensor 1 degree (POS)Crank / cam—
43Key switch STARTSensor signal—
44Neutral switchSensor signal—
45Key switch IGN (IGN)Power—
46Air conditioner switchSensor signal—
47Check (diagnosis) (CHK)Comms / diag—
48Throttle sensor powerSensor 5 V / ground—
49Control unit powerPower—
50Control unit earthGround—
51Crank angle sensor 120 degree (REF)Crank / cam—
52Crank angle sensor 1 degree (POS)Crank / cam—
53Vehicle speed sensorSensor signal—
56Throttle opening output signalSensor signal—
57Exhaust temperature sensorSensor signal—
58Battery powerPower—
59Control unit powerPower—
60Control unit earth (-)Ground—
101Injector No. 1Injector—
103Injector No. 3Injector—
104Fuel pump terminal power control output to FPCM (RB25DET only)Outputs—
105Injector No. 2Injector—
107Injector groundGround—
108Injector groundGround—
109Inverse current feedback circuitOther / not used—
110Injector No. 5Injector—
112Injector No. 6Injector—
113Variable valve timing solenoidOutputs—
114Injector No. 4Injector—
115Exhaust gas sensor heater groundGround—
116Injector groundGround—

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (low confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

Covers the R33 RB25DE/RB25DET ECCS unit from Nissan's R33 engine service manual. The R33 GT-R (RB26DETT) ECU is a different unit and is not covered.

Source notes: From the Nissan R33 engine service manual, 'ECCS control unit pin layout (RB25DE/RB25DET)' (EN-266). Unlisted terminals are shown as unused. The R33 GT-R (RB26DETT) layout in the same manual is close to the R32 GT-R table (twin air flow meters, FPCM outputs) and is not repeated here. Wire colours are not given.

Safety: disconnect the battery before working on the ECU harness, and confirm each terminal with a meter against your own car's manual before cutting or pinning wires.

All factory ECU pinouts →

Plug-and-play harness

Route for this carS3 plug-in harness
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.

MakerHarnessFitsLink
Nissan Skyline R32/R33/R34 GT-RHT-186362R32 GTS-t, R32 GT-R, R33 GTS-t, R33 GT-R, R34 GT-R; manual$535LowestMaker ↗
Manual 1993 - 1998 Nissan Skyline RB25DETBF29097-S31993-1998 R33 Skyline GTS-25t, manual; JDM$840Maker ↗
Wire-inUniversal flying lead or re-terminated factory harnessAny engine (terminate to ECU2's two Superseal 34 connectors)Universal harness from $405Maker ↗

Nexus S3 Plug n Play Adapter Harness Nissan Skyline R32/R33/R34 GT-R

$535USD list · excl. tax
Plug-and-playManual onlyOff-road / competition onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Nissan RB ECCS ECU (R32/R33 GTS-t, R32/R33/R34 GT-R) · 23710-05U02, 23710-05U60…
OEM part numbers
23710-05U02, 23710-05U60, 23710-05U61, 23710-05U62
ECU
Hitachi · Nissan 23710-series ECCS
Confidence
medium

Only R32 GT-R (RB26DETT) numbers sourced, with production-date split per forum citing Nissan parts. R32/R33 GTS-t and R33/R34 GT-R numbers not gathered; one harness spans several ECU generations.

Sources: E-1451

Fits
R32 GTS-t, R32 GT-R, R33 GTS-t, R33 GT-R, R34 GT-R; manual
Exclusions
R34 GT-T (use HT-186363); automatic
SKU
HT-186362
Maker fitment
Nissan Skyline R32 GTS-T, R32 GT-R, R33 GTS-T, R33 GT-R, R34 GT-R; manual only (kit page)
Maker notes
kit HT-213320 USD 2800

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1993 - 1998 Nissan Skyline RB25DET

$840USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
ECCS ECU (RB25DET, R33 Skyline GTS-t) · 23710-21U00, 23710-21U01…
OEM part numbers
23710-21U00, 23710-21U01, 23710-13U00
ECU
Nissan ECCS, RB25DET (ECR33)
Confidence
low

Forum/resale only: 21U00 and 21U01 described as R33 RB25DET; 13U00 described by a seller as R33 Series 2 manual. Series 1 vs Series 2 ECUs differ (immobiliser on S2 reported). blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)

Sources: E-1489

Fits
1993-1998 R33 Skyline GTS-25t, manual; JDM
Exclusions
R34 RB25DET NEO uses BF29132-S3; automatic
SKU
BF29097-S3
Maker fitment
Nissan Skyline RB25DET (Manual); selector years 1993-1998; SKU label: Manual 1993 - 1998 Nissan Skyline RB25DET
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2)

Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.

Your GAINS system for this car · pre-release

ECU2 for the Skyline GTS-t R33

Planned with the same rules as the configurator for this car's 6 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

  • ECU2Engine controller

    6 cyl · port injection · cable throttle

    Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harness1 listed · from $535 USD listHT-186362
  2. Factory-connector → S3 adapter1 listed · from $840 USD list
  3. Wire-inAlways possible

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Skyline GTS-t R33

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Cam phasing (VVT)gated

    Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.

  4. 4
    Boost controlgated

    A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.

  5. 5
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  6. 6
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAF (hot-wire / hot-film) (medium confidence)

  7. 7
    Wideband sensorhardware

    Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller

  8. 8
    Bottom end and head sealingfactory reference

    Reported: Stock oil pump commonly reported to break at high rpm (~8,000 rpm per a builder on SAU forum); stock turbo boost limit around 10 psi often cited (forum). (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Drivetrain

GTS25t transmissions
  • 5-speed manual or 4-speed automatic
  • AutoSpeed notes reduced output on automatic examples
Sourced · medium1
Automatic integration

Engine ECU exchanges DT1-DT3 control signals with the A/T controller

Sourced2

Chassis integration

TachometerEngine rev signal at terminal 7Sourced2
Warning lamps

Engine warning lamp (32) and exhaust temperature warning lamp (33) driven by the ECU

Sourced2
Vehicle speedVehicle speed sensor input at terminal 53Sourced2
A/CA/C switch (46) in, A/C relay (9) outSourced2

On automatic cars, a replacement ECU must provide or replace the DT1-DT3 engine-transmission signals, otherwise shift quality and torque reduction during shifts change. The exhaust temperature warning circuit uses a sensor on terminal 57.

Tuning notes

RB25DET output187 kW at 6,400 rpm, 294 Nm at 4,800 rpm (manual)Sourced · medium1
Injector flow370 cc RB25DET injectorsSourced · medium1
Injector drive
  • Approx. 1.3 ohm injectors
  • Keep resistor/current control or use high-impedance replacements
Sourced2

Typical R33 RB25DET steps are boost control, intercooler and exhaust, then injectors and fuel pump. Ceramic-wheel factory turbos are a common limit. Tune the VVT solenoid switch point with the rest of the calibration if moving to a standalone.

Popular swaps

Engine familyRB25DET shares its 86 mm bore with the RB26DETTSourced · medium1

R33 RB25DETs are widely used as swap engines for Nissan S-chassis and older Skylines. The R34 RB25DET NEO is a later evolution with different ignition, injector and fuel pump control hardware, so harnesses are not directly interchangeable.

GAINS on the Skyline GTS-t R33

ECU2

ECU2Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

Which R33 ECU pin is the boost control solenoid?

Terminal 25 (RB25DET only).2

Which R33 ECU pin drives the RB25 VVT solenoid?

Terminal 113, variable valve timing solenoid.2

Are R33 RB25DET injectors low impedance?

Yes, approx. 1.3 ohm per the R33 engine manual.2

What are the R33 RB25 crank angle sensor pins?

120 degree REF on 41 and 51, 1 degree POS on 42 and 52.2

Does the R33 RB25 ECU have an intake air temperature sensor?

No IAT input appears in the RB25DE/RB25DET ECU pin layout.2

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. The Late-Model Nissan RB Guide (Michael Knowling) · AutoSpeed (Web Publications Pty Ltd), archived copy · press · retrieved 2026-10-25
  2. Nissan R33 Engine Service Manual: RB20E, RB25DE, RB25DET and RB26DETT · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  1. E-925 Haltech S3 adapter harness page (sourced, high confidence)
  2. E-934 Boomslang identity (sourced, high confidence)
  3. E-935 Boomslang S3 catalog size (sourced, high confidence)
  4. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  5. E-941 S3 engine harness availability (inferred, medium confidence)
  6. E-1451 R32 GT-R ECU (supported, medium confidence)
  7. E-1489 harness ECU xref: Nissan R33 RB25DET (unverified, low confidence)