Engine: RB26DETT
Part of the Nissan RB family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (276 hp at 6800 rpm, 260 lb-ft at 4400 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.
RB26DETT data
- Load sensing
- MAF (hot-wire / hot-film)
- O2 sensor
- narrowband (zirconia)
- Closed loop
- narrowband closed loop (RICH/LEAN feedback) at light load; open loop at high load (Nissan FSM)
- Block
- cast iron
- Rods / pistons
- I-beam (Wikipedia) · cast with cooling channels under crown, piston oil squirters (Wikipedia)
- Reported limit
- ~450-600 hp on stock rods variously reported (forum); oil pump failure risk from ~400 whp (MotoIQ)
- Factory
- Top-feed, low-impedance (resistor box) · 444 cc/min
- Impedance
- low (peak and hold)
- Direct-fit upgrades
- 6 maker-listed
- Knock
- piezo knock sensor
- MAP / MAF
- 22680-05U00|Nismo Heritage B2680-RHR40
- O2 (upstream)
- narrowband zirconia
Platform background
The R32 Skyline (1989-1994) brought back the GT-R with the 2,568 cc RB26DETT, twin parallel turbos, six throttles, two hot-wire air flow meters and ATTESA E-TS four-wheel drive, while the GTS-t and GTS-4 used the 2.0 L RB20DET. This page gives the Nissan factory ECCS control unit pinout for the BNR32 RB26DETT from the R32 GT-R service manual.
Factory ECU
Terminals 1-60 (signal) and 101-116 (injector/power), with CONSULT RX, TX, CLK, CHK and IGN pins
Sourced3- Photoelectric crank angle sensor driven by the camshaft, left front of cylinder head
- 1 degree and 120 degree signals
- Six ignition signals to a separate 6-channel power transistor unit
- Mini-mould coil above each plug
The R32 GT-R ECU sums two airflow meters, so modifications to either intake side change the fuel calculation. It provides individual ignition and injection per cylinder, two knock channels, closed-loop O2 control on both banks, and pre-dates OBD-II standards.
Factory ECU: harness cross-reference
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Nissan 23710-series ECCS
- Applies to
- R32 GTS-t, R32 GT-R, R33 GTS-t, R33 GT-R, R34 GT-R; manual
- Not for
- R34 GT-T (use HT-186363); automatic
- Supplier
- Hitachi
Only R32 GT-R (RB26DETT) numbers sourced, with production-date split per forum citing Nissan parts. R32/R33 GTS-t and R33/R34 GT-R numbers not gathered; one harness spans several ECU generations.
- ECU family
- Nissan ECCS, RB26DETT (BNR32/BCNR33/BNR34)
- Applies to
- 1989-1998 Skyline GT-R RB26DETT (R32, R33), manual; JDM
- Not for
- R34 GT-R 1999-2002 uses BF29137-S3
R32 GT-R numbers via forum relay of a Nissan parts employee: 05U60 (8/91-4/92), 05U61 (4/92-2/93), 05U62 (2/93-). R33 GT-R numbers not found. One SKU spans R32 and R33 ECU generations. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
Factory ECU pinout
Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.
Nissan Skyline GT-R (BNR32) RB26DETT ECCS control unit
The Nissan Skyline GT-R (BNR32) RB26DETT ECCS control unit uses 1 connector with 76 cavities. This page draws each face from the OEM figure and lists the 63 terminals the OEM table documents, with wire colours where the manual prints them.
1989-1994 · Japan · 1 connector, 76 cavities · 63 terminals sourced
Looking into the harness plug's mating face (mirror of the ECU face).
How the OEM figure is oriented
Harness side (looking into the plug), as drawn in the OEM figure. Side confidence: low.| Pin | Function | Type | Wire | Notes |
|---|---|---|---|---|
| 1 | Ignition signal to power transistor, cylinder 1 | Ignition | — | |
| 2 | Ignition signal, cylinder 5 | Ignition | — | |
| 3 | Ignition signal, cylinder 3 | Ignition | — | |
| 4 | AAC valve | Outputs | — | |
| 6 | Sub electric fan relay (engine temperature switch) | Outputs | — | |
| 7 | Tachometer speed signal | Comms / diag | — | |
| 9 | Air conditioner relay (A/C cut signal) | Outputs | — | |
| 10 | Ground (ignition signal system) | Ground | — | |
| 11 | Ignition signal, cylinder 6 | Ignition | — | |
| 12 | Ignition signal, cylinder 2 | Ignition | — | |
| 13 | Ignition signal, cylinder 4 | Ignition | — | |
| 16 | ECCS relay | Outputs | — | |
| 18 | Fuel pump relay | Outputs | — | |
| 19 | Power steering oil pressure switch | Sensor signal | — | |
| 20 | Ground (ignition signal system) | Ground | — | |
| 21 | CONSULT receive (RX) | Comms / diag | — | |
| 22 | CONSULT transmit (TX) | Comms / diag | — | |
| 23 | Detonation (knock) sensor 1, cylinders 1-3 | Sensor signal | — | |
| 24 | Detonation (knock) sensor 2, cylinders 4-6 | Sensor signal | — | |
| 25 | Wastegate valve control solenoid valve | Outputs | — | |
| 26 | Air flow meter ground (rear) | Sensor 5 V / ground | — | |
| 27 | Air flow meter signal (rear) | Sensor signal | — | |
| 28 | Engine temperature sensor | Sensor signal | — | |
| 29 | Exhaust gas (O2) sensor, front | Sensor signal | — | |
| 30 | Sensor ground (throttle sensor, engine temperature sensor) | Sensor 5 V / ground | — | |
| 31 | CONSULT clock (CLK) | Comms / diag | — | |
| 32 | Monitor and check lamp (red) | Outputs | — | |
| 34 | Air flow meter ground (front) | Sensor 5 V / ground | — | |
| 35 | Air flow meter signal (front) | Sensor signal | — | |
| 36 | Intake air temperature sensor | Sensor signal | — | |
| 38 | Throttle opening output | Outputs | — | |
| 41 | Crank angle sensor 120 degree signal | Crank / cam | — | |
| 42 | Crank angle sensor 1 degree signal | Crank / cam | — | |
| 43 | Ignition switch START signal | Sensor signal | — | |
| 44 | Neutral switch | Sensor signal | — | |
| 45 | Ignition switch (IGN) | Power | — | |
| 46 | Air conditioner switch | Sensor signal | — | |
| 47 | Check (diagnosis activation) (CHK) | Comms / diag | — | |
| 48 | Throttle sensor power supply | Sensor 5 V / ground | — | |
| 49 | Control unit power supply | Power | — | |
| 50 | Ground (control unit) | Ground | — | |
| 51 | Crank angle sensor 120 degree signal | Crank / cam | — | |
| 52 | Crank angle sensor 1 degree signal | Crank / cam | — | |
| 53 | Vehicle speed sensor | Sensor signal | — | |
| 54 | Throttle valve switch (idle contact) | Sensor signal | — | |
| 55 | Exhaust gas (O2) sensor, rear | Sensor signal | — | |
| 56 | Throttle sensor output signal | Sensor signal | — | |
| 57 | Throttle valve switch power supply | Sensor 5 V / ground | — | |
| 58 | Battery power supply | Power | — | |
| 59 | Control unit power supply | Power | — | |
| 60 | Ground (control unit) (-) | Ground | — | |
| 101 | Injector No. 1 | Injector | — | |
| 103 | Injector No. 3 | Injector | — | |
| 104 | Fuel pump terminal voltage control output 1 (FPCM) | Outputs | — | |
| 105 | Injector No. 2 | Injector | — | |
| 106 | Fuel pump terminal voltage control output 2 (FPCM) | Outputs | — | |
| 107 | Injector ground | Ground | — | |
| 108 | Injector ground | Ground | — | |
| 109 | Injector power supply (counter-electromotive reflex circuit) | Power | — | |
| 110 | Injector No. 5 | Injector | — | |
| 112 | Injector No. 6 | Injector | — | |
| 114 | Injector No. 4 | Injector | — | |
| 116 | Injector ground | Ground | — |
Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (low confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.
Coverage, year splits and safety
Covers the BNR32 GT-R RB26DETT ECCS unit. The R32 GTS-t (RB20DET) shares the shared research guide but uses a different ECU and is not covered.
Source notes: From the Nissan GT-R Model R32 Series Service Manual, 'ECCS control unit pin layout figure: RB26DETT' (EN-171/172). Unlisted terminals (5, 8, 14, 15, 17, 33, 37, 39, 40, 102, 111, 113, 115) are shown as unused for this engine. Wire colours are not given in that table. The R32 GTS-t/GTS-4 RB20DET ECU pinout was not obtained; it needs the R32 (non-GT-R) service manual ECCS section.
Safety: disconnect the battery before working on the ECU harness, and confirm each terminal with a meter against your own car's manual before cutting or pinning wires.
Plug-and-play harness
A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
| Nissan Skyline R32/R33/R34 GT-RHT-186362 | R32 GTS-t, R32 GT-R, R33 GTS-t, R33 GT-R, R34 GT-R; manual | $535Lowest | Maker ↗ | |
![]() | Manual 1989 - 1998 Nissan Skyline RB26DETTBF29095-S3 | 1989-1998 Skyline GT-R RB26DETT (R32, R33), manual; JDM | $840 | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |
Nexus S3 Plug n Play Adapter Harness Nissan Skyline R32/R33/R34 GT-R
- Plugs into
Nissan RB ECCS ECU (R32/R33 GTS-t, R32/R33/R34 GT-R) · 23710-05U02, 23710-05U60…
- OEM part numbers
- 23710-05U02, 23710-05U60, 23710-05U61, 23710-05U62
- ECU
- Hitachi · Nissan 23710-series ECCS
- Confidence
- medium
Only R32 GT-R (RB26DETT) numbers sourced, with production-date split per forum citing Nissan parts. R32/R33 GTS-t and R33/R34 GT-R numbers not gathered; one harness spans several ECU generations.
Sources: E-1451
- Fits
- R32 GTS-t, R32 GT-R, R33 GTS-t, R33 GT-R, R34 GT-R; manual
- Exclusions
- R34 GT-T (use HT-186363); automatic
- SKU
- HT-186362
- Maker fitment
- Nissan Skyline R32 GTS-T, R32 GT-R, R33 GTS-T, R33 GT-R, R34 GT-R; manual only (kit page)
- Maker notes
- kit HT-213320 USD 2800

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1989 - 1998 Nissan Skyline RB26DETT
- Plugs into
ECCS ECU (RB26DETT, R32/R33/R34 Skyline GT-R) · 23710-05U60, 23710-05U61…
- OEM part numbers
- 23710-05U60, 23710-05U61, 23710-05U62
- ECU
- Nissan ECCS, RB26DETT (BNR32/BCNR33/BNR34)
- Confidence
- low
R32 GT-R numbers via forum relay of a Nissan parts employee: 05U60 (8/91-4/92), 05U61 (4/92-2/93), 05U62 (2/93-). R33 GT-R numbers not found. One SKU spans R32 and R33 ECU generations. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
Sources: E-1488
- Fits
- 1989-1998 Skyline GT-R RB26DETT (R32, R33), manual; JDM
- Exclusions
- R34 GT-R 1999-2002 uses BF29137-S3
- SKU
- BF29095-S3
- Maker fitment
- Nissan Skyline RB26DETT (Manual); selector years 1989-1998; SKU label: Manual 1989 - 1998 Nissan Skyline RB26DETT
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2)
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the Skyline GT-R R32
Planned with the same rules as the configurator for this car's 6 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.
- Price TBA
ECU2Engine controller
6 cyl · port injection · cable throttle
Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harness1 listed · from $535 USD listHT-186362
- Factory-connector → S3 adapter1 listed · from $840 USD list
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
Swap guides
The RB26DETT family in other cars
How GAINS approaches the Skyline GT-R R32
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3Boost controlgated
A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.
- 4Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 5Factory load sensingfactory reference
What the factory ECU measures load with: MAF (hot-wire / hot-film) (high confidence)
- 6Wideband sensorhardware
Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller
- 7Bottom end and head sealingfactory reference
Reported: Per MotoIQ, the oil pump gears (driven by a narrow crank flat) fracture past ~400 whp or over-rev, attributed to crank torsional harmonic ~7,000-8,000 rpm; block flex reported in the 500s whp. (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
Drivetrain
Chassis integration
Thermocouple-type exhaust temperature warning equipment, set at 850 C
Sourced3ATTESA E-TS and HICAS have their own controllers; a standalone engine ECU must still supply the vehicle speed and throttle information those systems expect where they are wired from the engine side. Check the chassis wiring diagram before deleting the factory throttle opening output (terminal 38).
Tuning notes
AutoSpeed reports the R32 RB26DETT closer to about 225 kW than the rated figure
Sourced · medium1Common R32 GT-R steps are boost increase via the wastegate solenoid control, fuel pump upgrade (with FPCM retained or bypassed), larger air flow meters or a standalone ECU with MAP-based load, and turbo upgrades to replace the ceramic-wheel factory units. Log both knock channels and per-bank lambda during development.
Popular swaps
- R32-spec RB20DET also fitted to Cefiro and Laurel
- Popular for conversions
RB25DET and RB26DETT conversions into GTS-t/GTS-4 bodies are common. A wiring plan is required because the RB26 ECU expects two airflow meters, FPCM fuel pump control and GT-R-specific inputs.
GAINS on the Skyline GT-R R32
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Frequently asked
Where is the ECU in an R32 GT-R?
Inside the left-hand dash side lower finisher, per the R32 GT-R service manual.3
What are the R32 GT-R crank angle sensor pins?
120 degree signals on terminals 41 and 51, 1 degree signals on 42 and 52.3
Which R32 GT-R ECU pins are the injectors?
101 (No.1), 105 (No.2), 103 (No.3), 114 (No.4), 110 (No.5), 112 (No.6), with injector grounds on 107, 108 and 116.3
How many air flow meters does the R32 GT-R have?
Two hot-wire meters, front (signal 35, ground 34) and rear (signal 27, ground 26).3
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- The Late-Model Nissan RB Guide (Michael Knowling) · AutoSpeed (Web Publications Pty Ltd), archived copy · press · retrieved 2026-10-25
- Nissan Heritage Collection: Skyline GT-R (1989, BNR32) · Nissan Motor Co., Ltd. · oem · retrieved 2026-10-25
- Nissan GT-R Model R32 Series Service Manual (sections GI, EN: B1 Engine specifications, B3 ECCS) · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
- Nissan R33 Engine Service Manual: RB20E, RB25DE, RB25DET and RB26DETT · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-925 Haltech S3 adapter harness page (sourced, high confidence)
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)
- E-1451 R32 GT-R ECU (supported, medium confidence)
- E-1488 harness ECU xref: Nissan R32 GT-R RB26DETT (unverified, low confidence)


