2JZ Swap Nissan 240SX S13 (1989-94): 2JZ-GTE and 2JZ-GE Guide

A 2JZ 240SX swap is a popular drift and street build, with bolt-in mount kits for the 1989-94 S13. It takes a 2JZ-GTE or 2JZ-GE, swap mounts, a Toyota R154 or adapted Nissan CD00x gearbox, a custom driveshaft and full engine wiring. The main hurdles are hood and tunnel clearance, cooling and fueling the bigger engine, and the wiring.Medium456

Difficulty3/5 · ModerateMedium456
  • Bolt-in mount kits exist, but builders still report mounts that needed fabrication to line up.
  • The taller 2JZ block may need the hood's inner ribbing trimmed or the rear of the hood spaced up.
  • Every gearbox option needs adapting: R154 mounts, or a CD00x with an adapter and Toyota bellhousing, plus a custom driveshaft.
  • A full engine harness and engine management are needed; one magazine build reports a month on wiring alone.

At a glance

The key numbers and parts, with the source on each tile.

Mount kits

Bolt-in engine and gearbox mounts for S13/S14, supporting R154 or CD00x

Sourced · medium4
Recommended engines
  • 2JZ-GTE (turbo) for power
  • 2JZ-GE (NA) for budget or a later turbo build
Sourced · medium2
Toyota ratings (Japan, 1993)
ItemPowerTorque
2JZ-GTE280 PS276 hp · 206 kW44.0 kg-m318 lb-ft · 431 Nm
2JZ-GE225 PS222 hp · 165 kW29.0 kg-m210 lb-ft · 284 Nm
Export Supra Turbo figures differ; Wikipedia lists 320 hp (239 kW) for North America and Europe.Sourced1
ConstructionCast-iron block, aluminum head, belt-driven DOHC inline sixNo OEM engine weight found; expect more weight over the front axle than the original four- or six-cylinder.Sourced · medium2
Factory injectors (GTE)
  • 550 cc/min export
  • 440 cc/min Japan
Sourced · medium2
Transmissions
  • Toyota R154
  • Nissan CD00x via adapter
  • Factory V160/V161rare
Sourced · medium352
HoodMay need inner ribbing trimmed or the rear of the hood spaced upSourced · medium4
ThrottleToyota lists electronic throttle control on the 1993 turbo SupraSourced1
Load sensing

Forum reports: Japanese engines MAP-based, export Supras airflow-meter based

Low confidence7

Recommended engines

  • 2JZ-GTE (non-VVT-i) · The 1993-97 twin-turbo engine Toyota rated at 280 PS (276 hp, 206 kW) in Japan; no cam phasing to control, so the wiring and calibration are simpler than the VVT-i version.
  • 2JZ-GTE VVT-i · Adds VVT-i intake cam phasing from September 1997 and a torque rating of 46 kg-m in Japanese spec; better midrange, but the cam control must be wired and calibrated.
  • 2JZ-GE (NA, VVT-i 1998+) · The naturally aspirated 2JZ is far more common and cheaper, found in Supra, SC300, GS300 and IS300 models; it shares its block, crankshaft and rods with the GTE, which makes it a popular base for later turbocharging.

Mounts

A 2JZ 240SX swap normally starts with a bolt-in mount kit.

Kit contents (ISR)

Left and right engine mounts, gearbox mount, two front crossmember U-brackets, gearbox brace, hardware

Sourced4
Gearbox support

R154, or CD00x with a newer Collins adapter and Toyota bellhousing

Sourced4
Fit in practice

A DSPORT-featured build needed fabrication before the mounts lined up

Sourced · medium6

ISR's kit for the S13 and S14 includes left and right engine mounts, a gearbox mount, two front crossmember U-brackets, a gearbox brace and hardware, and supports either an R154 or a CD00x gearbox.4

Kits do not remove all fitting work. DSPORT's 2019 feature on an S13 2JZ-GTE build reports that the engine mounts did not line up at first and needed custom fabrication. Test-fit the engine and gearbox before final welding or paint.Medium6

Transmission

The R154 five-speed is the usual first choice because it bolts to the JZ bellhousing pattern and mount kits support it.

R154

Used in the Mk III Supra Turbo, Soarer turbo, Crown and Chaser/Mark II/Cresta Tourer V

Sourced · medium3
CD009 adapter
  • Reuses the Toyota J3 automatic bellhousing (A340E)
  • J2 does not work
Sourced5
CD009 clutch releaseHydraulic release bearing and 3/4 in master cylinder requiredSourced5
Factory 2JZ-GTE manualV160/V161 six-speed developed with GetragSourced · medium21

Toyota fitted it to the Mk III Supra Turbo, turbo Soarer, Crown and the Chaser, Mark II and Cresta Tourer V. Gearbox tunnel clearance can depend on which R154 version and shifter you use.Medium34

The Nissan CD009 six-speed from the 350Z and 370Z needs an adapter. One adapter maker's kit reuses the J3 automatic bellhousing from A340E-equipped 2JZ-GTE cars, warns that the J2 bellhousing will not work, and requires a hydraulic release bearing and a 3/4 in master cylinder. The original V160/V161 is the factory pairing but is rare.Medium52

Every option changes gearbox length, so plan a custom or modified driveshaft measured with the engine and gearbox on their final mounts. Balance it and check driveline angles before driving.Low5

Clearance

The 2JZ is taller than the KA24 and SR20 the S13 was built around.

Hood

2JZ deck height may need inner hood ribbing trimmed and the rear of the hood spaced

Sourced4
TunnelCD00x brace offered with a weld-in tunnel clearance kitSourced · medium4

ISR warns its added deck height may require trimming the hood's internal ribbing and, depending on the chassis, spacing the rear of the hood up. Check hood clearance with the intake manifold and throttle body fitted.4

Behind the engine, a CD00x gearbox is bulkier than the original. ISR offers a weld-in clearance kit for the transmission tunnel with its CD00x brace. Check the steering shaft, brake lines and firewall against the exhaust manifold and turbos too.Medium4

Cooling

A 2JZ-GTE rated at 280 PS (206 kW) in Japanese trim rejects far more heat than the original engine.

Heat load2JZ-GTE rated 280 PS in Japanese trim206 kWSourced1
IntercoolerFactory 2JZ-GTE uses a side-mount air-to-air intercoolerSourced · medium2

Fit a larger aluminum radiator, electric fans with a proper shroud, and a separate oil cooler for track or drift use. Route hoses clear of the turbo and exhaust manifold.Medium1

The factory 2JZ-GTE uses a side-mount air-to-air intercooler that does not suit the S13 nose. Most swaps fit a front-mount intercooler, which then shares the opening with the radiator and A/C condenser, so plan airflow and ducting together. Bleed air from the highest point and never open a hot system.Low2

Fuel

Size the fuel system for the power you plan, not the stock rating.

Factory injectors2JZ-GTE: 550 cc/min export, 440 cc/min JapanSourced · medium2
Turbo layout

Sequential twin turbochargers with a side-mount air-to-air intercooler

Sourced · medium2

Wikipedia lists the export 2JZ-GTE with 550 cc/min injectors and the Japanese engine with 440 cc/min units. Check the S13's in-tank pump, lines and filter against the target flow, and add a return line if the chassis lacks one.Medium2

If you plan to run E85 or flex fuel, plan substantially more fuel flow than gasoline needs, and choose pump, injectors, hoses and seals rated for ethanol. Fit a fuel pressure gauge and log pressure under boost.Low2

Exhaust

Factory turbosSequential twins: CT20 (Japan), CT12B (export)Sourced · medium2
Turbo control

Sequential system adds valves and vacuum controls to wire or replace

Sourced · medium2

The factory 2JZ-GTE uses sequential twin turbochargers developed with Hitachi, with CT20 units in Japan and CT12B units for export. The sequential system relies on valves and vacuum controls that must be wired and plumbed, so some swaps keep it and others replace it with a single turbo and new manifold.Medium2

Whatever the layout, route the downpipe clear of the steering shaft, firewall and S13 floor, and keep heat away from brake lines and wiring with shielding. Leave a wideband oxygen sensor bung after the turbine where gas is well mixed.Low2

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads
Harness work
  • One featured S13 build took about a month to wire
  • Matching connectors and pins was the main problem
Sourced · medium6
Ignition hardware
  • Varies by year
  • Sources disagree on coil layout
Low confidence2
ThrottleToyota lists electronic throttle control on 1993 turbo SuprasSourced1

The engine needs power and grounds, crank and cam position signals, injector and ignition outputs, throttle position, manifold pressure or airflow, coolant and intake temperature, knock sensors and an oxygen sensor. VVT-i engines add an oil control valve and cam angle feedback. DSPORT's featured build spent about a month on wiring, with connector matching the biggest problem.Medium62

Confirm ignition and throttle hardware on your donor. Wikipedia describes the 2JZ-GE as distributorless with one coil serving two cylinders, while later VVT-i engines are widely reported with individual coils; Toyota lists electronic throttle control on the 1993 turbo Supra. Decide how the throttle and turbo control valves will be driven before buying engine management.Low21

The S13 still needs a tachometer signal, coolant and oil pressure senders its gauges read, fuel pump relay control, fan control and A/C request. Check whether the donor computer expects an immobilizer. Fuse every circuit at the source, size wire for the load and relay the pump, fans and main power.Low1

Chassis

The 2JZ-GTE's rated torque is well beyond what the S13's original driveline saw.

Torque2JZ-GTE rated 44.0 kg-m in Japanese trim318 lb-ft · 431 NmSourced1
Weight distribution
  • Kits set the engine low and back where possible
  • The long inline six still adds front weight
Low confidence42

Inspect or upgrade the differential, axles and driveshaft, and fit brakes that can repeat hard stops. A long cast-iron inline six adds weight over the front axle, so re-check alignment and corner weights after the swap.Low12

Drift and track builds add a seat, harness and cage, but the street minimum is brakes, tires and a cooling system that survives heat soak. Check subframe and mount bolts after the first hard drives.Low1

Tuning

Factory load sensing

Reported to vary by market: MAP on Japanese engines, airflow meter on export cars

Low confidence7
Cam controlVVT-i on the intake cam from 1997 (GTE) and mid-1990s (GE)Sourced · medium2

Most 2JZ swaps are calibrated on manifold pressure (speed density) or with an airflow meter, depending on the engine computer and intake. Start from injector data, then correct the fuel table from wideband logs. Changing turbos, intake or cams changes volumetric efficiency, so a donor map is only a starting point.Medium2

Boost needs layered protection

A wastegate sized for the turbo, closed-loop boost control with an overboost cut, and knock monitoring. Advance ignition only as far as knock data and logs support on your fuel; there is no single safe figure.Medium2

Log intake air temperature after the intercooler, lambda, boost, coolant and oil temperature, and knock activity. On VVT-i engines, log intake cam angle against target and keep idle overlap modest for stable running.Low2

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 23 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Plan the combination
    Choose engine, gearbox, turbo layout and engine management together, then order mounts and adapters that match.
  2. Inspect the donor
    Check compression and leak-down, replace the timing belt, water pump and seals, and fit a fresh clutch.
  3. Strip the S13
    Remove the old engine, gearbox, driveshaft and engine-bay wiring. Label everything you will reuse.
  4. Fit mounts and test-fit
    Install the mount kit, lower the engine and gearbox on a hoist with a load leveler, and check hood, tunnel and steering shaft clearance.
  5. Fabricate as needed
    Trim hood ribbing, add tunnel clearance or adjust brackets, then seal and paint bare metal.
  6. Driveline
    Measure and order the driveshaft with the engine on final mounts; fit clutch hydraulics and bleed.
  7. Cooling, fuel and exhaust
    Install radiator, intercooler, fuel system and exhaust; pressure-test fuel and coolant.
  8. Wire and start
    Fit harness, relays and gauges; prime oil pressure, confirm cam/crank sync and fuel pressure, then start and check for leaks.
  9. Calibrate
    Build fuel and boost control from wideband logs at low boost first, watching knock and temperatures.
  10. Shake down and register
    Re-torque mounts and driveline, then complete emissions, registration and insurance steps.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Hood will not close2JZ deck height hits the hood's inner ribbingTrim the inner ribbing or space the rear of the hood, as the mount maker suggests.4
Mounts do not line upVariation between kits, chassis and enginesTest-fit before welding; adjust or fabricate brackets as a featured build had to.Medium6
CD009 will not bolt upWrong Toyota bellhousing used with the adapterUse the J3 automatic bellhousing the adapter kit specifies; the J2 does not work.5
Clutch will not release with CD009Missing hydraulic release bearing or wrong master cylinder sizeFit the hydraulic release bearing and 3/4 in master cylinder the adapter maker requires.5
Engine runs but no tach or wrong gauge readingsS13 gauges not fed with compatible signalsProvide a tach output and senders the S13 cluster understands.Low6
Fails a California Referee inspectionDonor emissions controls missing or disconnectedFit and connect the donor's emissions controls; the Referee tests to the donor vehicle's smog requirements.9

Frequently asked

What transmission do you use for a 2JZ 240SX?

The Toyota R154 five-speed is the most common because it bolts to the JZ engine and mount kits support it. The Nissan CD009 six-speed also works with an adapter that uses a Toyota J3 automatic bellhousing. The factory V160/V161 six-speed is the original pairing but is rare.Medium352

Does a 2JZ fit in an S13 without cutting?

Mostly, with caveats. Bolt-in mount kits exist, but ISR warns the taller 2JZ block may require trimming the hood's inner ribbing, and a CD00x gearbox may need tunnel clearance. A DSPORT-featured build also needed fabricated mount brackets, so expect some fitting work.Medium46

Should I use a 2JZ-GE or 2JZ-GTE in a 240SX?

The GTE has factory turbos and Toyota rated it at 280 PS (276 hp) in Japan, but it costs more. The GE is cheaper and widespread in SC300, GS300 and IS300 models, and it shares its block, crankshaft and rods with the GTE, so many builders add a turbo later.Medium12

Do you need a custom driveshaft for a 2JZ 240SX?

Yes, in nearly every case. The R154, CD009 and other options all change gearbox length and output position compared with the original S13 gearbox. Measure with the engine and gearbox on final mounts and have a driveshaft built and balanced to suit.Low54

How hard is wiring a 2JZ into an S13?

It is the biggest single job. DSPORT's featured S13 build reports about a month of wiring, with matching connectors and pins as the main problem. You must power the engine, run its sensors, injectors, ignition and throttle, and still feed the S13's gauges.Medium6

Is a 2JZ 240SX street legal?

It can be, depending on location. California requires a BAR Referee inspection against the donor vehicle's smog rules, the UK requires a V5C update with evidence, Germany needs an inspector's approval and Australian states apply VSB 14. This is general information, not legal advice.Medium9101112

Related

Sources

12 sources
  1. Toyota launches all-new Supra (May 1993 release, 75 Years of Toyota archive) · Toyota Motor Corporation · oem · retrieved 2026-10-25
  2. Toyota JZ engine · Wikipedia · reference · retrieved 2026-10-25
  3. Toyota R transmission · Wikipedia · reference · retrieved 2026-10-25
  4. ISR Performance JZ Swap Mounts for Nissan 240sx S13/14 · ISR Performance · vendor-doc · retrieved 2026-10-25
  5. 2JZ Billet CD009 Adapter Plate (product page) · XAT Racing · vendor-doc · retrieved 2026-10-25
  6. 2JZ-GTE Powered Nissan 240SX (Bassem Girgis, June 2019) · DSPORT Magazine · press · retrieved 2026-10-25
  7. Confused about air intake metering (forum thread) · MKIVSupra.net · community · retrieved 2026-10-25
  8. Tampering Policy: The EPA Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices under the Clean Air Act (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  9. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-25
  10. Change vehicle details on a V5C: what evidence to give · GOV.UK (DVLA) · standard · retrieved 2026-10-25
  11. Strassenverkehrs-Zulassungs-Ordnung (StVZO) section 19: Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  12. Vehicle Standards Bulletin 14 (VSB 14): National Code of Practice for Light Vehicle Construction and Modification · Australian Government, Department of Infrastructure · standard · retrieved 2026-10-25