Brake specific fuel consumption (BSFC)

BSFCspecific fuel consumptionSFClb/hp·hrg/kWh

Brake specific fuel consumption (BSFC) is the fuel mass an engine burns per unit of power it delivers at the crankshaft, per hour. It is quoted in lb/hp·h or g/kWh; lower is more efficient. Tuners use it to estimate fuel flow and size injectors and pumps.12

How it works

Brake specific fuel consumption divides fuel flow by brake power, the power measured at the output shaft.

It lets engines of different sizes be compared on efficiency, and it varies across the speed and load map, usually shown as a BSFC contour plot.12

BSFC and brake thermal efficiency are inverses once fuel heating value is known. For gasoline, efficiency equals 1 ÷ (BSFC in g/kWh × 0.0122225). Wikipedia gives about 225 g/kWh, roughly 36% efficiency, as a typical best point for a production gasoline engine.Medium1

Recent engines go further. Toyota reports 40% thermal efficiency for its 2.0 L Dynamic Force gasoline engine and 41% for the hybrid version, which works out to about 205 g/kWh at 40% using the same heating value.Medium31

Units convert as 1 lb/hp·h = 608.277 g/kWh. A figure of 0.50 lb/hp·h is about 304 g/kWh, or roughly 27% efficiency on gasoline.1

In tuning

For injector and pump sizing, tuners use an assumed full-load BSFC.

Rich mixtures for knock and temperature control raise BSFC above the engine's best value, so boosted engines are usually sized with higher BSFC assumptions than naturally aspirated ones. Treat the figure as a planning input and confirm with measured flow.Medium21

On a dyno with fuel-flow measurement, BSFC across the map shows where an engine is efficient. Lean, well-phased combustion lowers it; excessive enrichment, retarded ignition and high friction raise it.2

Formula and worked example

BSFC = ṁ_fuel / P_brake
BSFC
brake specific fuel consumptiong/kWh or lb/hp·h
ṁ_fuel
fuel mass flowg/h or lb/h
P_brake
brake power at the crankshaftkW or hp
12

Try it

hp
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

%

Size for 80-85% so the injector still has control margin at peak power.

Result

Flow per injector75.0 lb/hr
Total fuel flow240 lb/hr

Planning estimate from the formula below, not a measurement.

Open the full fuel injector size calculator →

Myths vs facts

Myth BSFC is a fixed number for an engine.

Fact BSFC varies with speed, load, mixture and ignition timing. A single quoted value is either the best point or an assumption for a specific condition.12

Myth Lower BSFC assumptions are safer for injector sizing.

Fact Assuming a low BSFC undersizes the fuel system. Rich full-load targets raise real BSFC, so optimistic assumptions can leave injectors at their limit.Medium2

Frequently asked

What is a typical BSFC for a gasoline engine?

At its best operating point, a modern production gasoline engine is around 225 g/kWh (about 0.37 lb/hp·h), equal to roughly 36% efficiency. Toyota reports 40% efficiency for its latest 2.0 L engine, about 205 g/kWh. Full-load rich operation is considerably higher.Medium13

How do you convert BSFC to efficiency?

Brake thermal efficiency equals 3,600 divided by BSFC in g/kWh times fuel lower heating value in MJ/kg. Using about 44 MJ/kg for gasoline, 225 g/kWh is about 36% and 304 g/kWh is about 27%. Diesel uses its own heating value.12

How do you use BSFC to size injectors?

Multiply target power by BSFC to get total fuel flow per hour, divide by the number of injectors, then divide by the maximum duty you plan to use. The result is the static flow each injector needs at your fuel pressure. Use a conservative, higher BSFC for boosted engines.Medium12

Why use a higher BSFC for turbocharged engines?

Boosted gasoline engines usually run richer at full load to control knock and exhaust temperature, which burns more fuel per unit power. Sizing with a higher BSFC assumption leaves enough injector and pump capacity for that enrichment, plus margin for fuel pressure and voltage variation.Medium21

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Brake-specific fuel consumption · Wikipedia · reference · retrieved 2026-10-25
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-25
  3. TNGA powertrain: Dynamic Force engine · Toyota Motor Corporation · oem · retrieved 2026-10-25