Subaru BRZ / Scion FR-S / Toyota 86 K Swap (2013-2020): K24 Mounts, Stock Gearbox, CAN Bus, Wiring and Legal Guide

A K swap BRZ, FR-S or 86 is a growing swap with one complete kit: KPower's K24 package keeps the factory 6-speed through a thick adapter plate, moves the engine low and back, and plugs into the chassis harness. The main decisions are the engine block the mounts accept, the oil pan and pump, and a CAN-capable engine computer.Medium453

Difficulty3/5 · ModerateMedium3459
  • KPower's complete package needs no subframe changes, cutting or wiring splices, but it only supports manual cars and specific K blocks.
  • The engine needs a rear-drive oil pan with a K20 oil pump, or a balance-shaft pan with a subframe modification.
  • The 86 is a CAN-bus car, so the engine computer must speak to the cluster, ABS and climate control.
  • Kits without KPower's mounts, such as Collins's adapter, need sheet-metal work, a shortened shift linkage and custom mounts.

At a glance

The key numbers and parts, with the source on each tile.

Stock engine
  • 2.0 L FA20 flat-four
  • Subaru rated it at 200 hp and 151 lb-ft2013 BRZ
Sourced1
K24A2 rating

Acura rated the TSX K24A2 at 200 hp (2004-05) and 205 hp (2006-08)

Sourced · medium11
Main kit
  • KPower complete, race and builder packages
  • Collins and PMC adapter kits
Sourced · medium4910
Gearbox
  • Factory 86 6-speed manual, moved about 4 in rearward100 mm
  • No automatic support
Sourced · medium3
Supported blocks (KPower mounts)
  • K24A RBB, K24A2, K24A3, K24A4, K20Z3, K20Z4, K24A8
  • Not K20A2, K20Z1 or K24A1
Sourced · medium4
Hood and ground clearanceStock hood closes and the undertray fits, per KPowerSourced · medium35
Weight changeKPower measured 140 lb less than its stock car with A/C64 kgSourced · medium35
Electronics
  • Plug-in engine harness and CAN-capable standalone ECU
  • Factory computer removed
Sourced · medium45
Legal route
  • Sold for off-road use
  • Road legality depends on local emissions rules
Sourced · medium414

Recommended engines

  • K24A2 (TSX) · The engine KPower developed and tested its 86 package around. Its mount brackets bolt to the K24A2, and its harness is built for 2004-2008 K24A sensors and the 2006-2008 TSX A/C compressor.
  • K20Z1 / K20Z3 · KPower lists the K20Z3 and K20Z4 blocks as fitting its 86 mount brackets, so a Civic Si engine is a supported choice; check sensor and harness compatibility with the kit maker.
  • K20A2 (RSX Type S / EP3 EU Type R) · Adapter makers such as Collins and PMC cover K20 and K24 engines to the 86 gearbox, but KPower says its brackets do not fit the K20A2 block, so expect custom mount work with this engine.

Mounts

For a K swap BRZ, KPower's package is the only complete kit found.

KPower brackets

Laser-cut, TIG-welded brackets that take OEM Subaru Impreza rubber mounts

Sourced · medium5
Engine position

Crank centerline about 2.5 in (64 mm) lower and engine about 4 in (100 mm) further back than stock

Sourced · medium53
Block fitNot K20A2, K20Z1 or K24A1 because of left-side bolt holesSourced · medium4

Its brackets accept OEM Subaru Impreza rubber mounts to keep vibration low, and the stock 86 transmission mount stays with a Whiteline insert. KPower says no subframe removal, fabrication or bellhousing cutting is needed.Medium53

Press coverage at launch, such as autoevolution's in August 2021, restated KPower's claims of a plug-in harness and retained factory dash functions, and noted that standalone-ECU kits are not street legal in California.Medium6

Check the block before buying an engine. KPower's mounts bolt to the JDM K24A RBB, K24A2, K24A3, K24A4, K20Z3, K20Z4 and K24A8, but not the K20A2, K20Z1 or K24A1, whose left-side bolt holes differ.Medium4

Collins Performance sells a K-to-86 adapter kit, but its listing said engine mounts were still in development. Pure Automotive Performance also showed a kit in 2018. Neither offers a complete mount package that could be confirmed.Low98

Transmission

KPower keeps the factory 6-speed manual and moves it about 4 in rearward and lower in the tunnel.

Stock gearbox6-speed TL70 manual, based on the Aisin AZ6Sourced · medium2
KPower adapter
  • 6061 aluminum plate about twice as thick as its steel plates
  • Factory 86 clutch, fork, bearing and slave fit
Sourced · medium5
Driveshaft

Two-piece factory shaft (about 29 lb) replaced by a one-piece 3 in aluminum shaft (about 16 lb)

Sourced · medium5

Its package includes a relocated transmission mount bracket, a shifter plate for the OEM lever and a dual-shear selector rod. KPower supports only the manual; automatic cars need a manual conversion.Medium34

The adapter plate is thick 6061 aluminum, so any factory-style 86 clutch, fork, release bearing and slave cylinder fits, and the K-series starter fits unmodified. KPower now ships a steel flywheel as standard. KPower says the stock gearbox suits stock and built naturally aspirated engines and mild boost.Medium543

Collins's route also uses the stock gearbox but pushes it back further. Collins says you must bash the passenger-side inner transmission crossmember sheet metal, cut 1/4 in (6 mm) off the slave cylinder rod, fit a new driveshaft and shorten the shift linkage.Medium9

PMC Motorsport in Europe sells adapter kits for K20 and K24 engines to the AZ6-based gearbox in the GT86, BRZ and FR-S.Medium10

Clearance

The FWD K-series pan hits the 86 subframe, so the swap uses a rear-drive pan.

KPower pan options

PRB pan or 9 qt Unit2 pan with a K20 oil pump, or an RBB pan for the stock K24 balance-shaft pump

Sourced · medium4
RBB pan noteNeeds a weld-in subframe plate or KPower's pre-modified subframeSourced · medium4
Collins route
  • Front-sump K pan with an RSX Type-S pump
  • Engine sits at a slant
Sourced · medium9

KPower's standard pan clears the stock subframe, keeps the drain in the stock 86 spot, and uses a complete K20 oil pump and pickup; the K20 Type S pump is listed as required in its OEM parts bundle.Medium54

If you want to keep the K24's smoother balance-shaft pump, KPower's RBB pan needs a weld-in subframe plate or its pre-modified subframe. Collins instead calls for a front-sump K pan, or a modified OEM pan, with an RSX Type-S pump.Medium49

KPower says the stock hood closes over the K24 without changes and the whole drivetrain sits about 1 in (25 mm) above the factory undertray, so ground clearance stays stock. Those figures are for its mounts; other kits may differ.Medium35

Cooling

KPower keeps the factory 86 radiator location.

Upper neck

KPower 86 neck routes coolant to the right side to meet the factory radiator inlet

Sourced · medium5
HeaterTwo OEM Honda heater hoses plus a 5/8 in barbed fittingSourced · medium5

Its upper water neck turns the outlet to the right side so the upper hose reaches the stock inlet, and couplers step 1.25 in to 1.50 in hoses so OEM-style hoses fit.Medium5

Heat uses two OEM Honda heater hoses with a 5/8 in barbed fitting. KPower's complete package also lists a thermostat inlet plug and an optional A/C and heater hose set.Medium54

Fuel

The FA20 runs Toyota's D-4S direct plus port injection, while the K24 uses port injection only.

Stock tank13.2gal50 LSourced1
KPower fuel parts

Fuel rail, 5/16 in quick-disconnect inlet, E85-compatible hose, fuel pump relay kit

Sourced · medium54
FA20 leftovers
  • Plug for the second (direct-injection) injector feed
  • Factory fuel pump controller bypassed
Sourced · medium5

KPower supplies a rail with a 5/16 in quick-disconnect inlet, E85-compatible hose to the main feed, and a plug to close the line that fed the FA20's second injector set.Medium15

KPower bypasses the factory fuel pump controller with connectors and a relay kit so the new engine computer runs the pump. Check that the in-tank pump suits your fuel and power level before reusing it.Medium54

Exhaust

No existing K header fits the 86 bay, so KPower designed a 304 stainless 4-2-1 header.

KPower header

304 stainless 4-2-1, cylinders 1-4 and 2-3 paired, 3-bolt collector

Sourced · medium5
Midpipe

3 in stainless midpipe with flex section, ending where the stock midpipe flange sits

Sourced · medium54

A short 3 in midpipe passes the lowered gearbox and ends at the stock midpipe flange position, so any 3 in 86 cat-back exhaust bolts on.Medium35

The midpipe has a port for the wideband sensor. Plan catalysts where your emissions rules require them, since the package exhaust is sold for off-road use.Medium54

Electrical

ECU+ PDM / relaysCrank / cam sensorsThrottle (DBW) + pedalInjectorsCoilsEngine sensorsFuel pumpCooling fansGauges / tachStarter / chargingChassis loads

The factory 86 engine computer is removed.

Harness
  • Plug-in K harness that meets the factory 86 engine harness connector
  • No firewall pass-through, glovebox only
Sourced · medium53
Retained functions

Gauges, climate control, A/C, ABS, cruise and traction control, per KPower

Sourced · medium357
SteeringElectric power steering needs no changes, per KPowerSourced · medium31

KPower uses a standalone ECU that already supports the 86 CAN messages, which lets its harness keep the gauges, climate control, ABS, cruise and traction control working. It also keeps the factory pedal and drive-by-wire throttle body.Medium35

The engine harness plugs into the same chassis connector the FA20 harness used. The ECU and a jumper board sit under the dash, installed by moving only the glovebox, with no splices and no new wires through the firewall.Medium53

The harness is built for 2004-2008 K24A sensors and the 2006-2008 TSX A/C compressor; KPower warns that not all K24 compressors are the same. The 86's steering is electric, so KPower says assist needs no changes.Medium431

Chassis

Weight

KPower's back-to-back weighing showed 140 lb (64 kg) less with the K24 and its parts

Sourced · medium3
Differential
  • Torsen limited-slip, 4.100 final drive2013 BRZ
  • 4.30 on the 2017+ manual 86
Sourced12
Rear axlesA known weak point on lowered cars with wide wheelsLow confidence12

KPower weighed its BRZ before and after the swap and reports 140 lb less with the K24, accessories and A/C, with the drivetrain lower and further back. That figure is the maker's own measurement on one car.Medium35

Acura rated the K24A2 at 164-166 lb-ft, close to the FA20's 151 lb-ft, so the stock Torsen differential is less stressed than in a V8 swap. Lowered 86s still pop rear axles, so inspect the boots and carry a spare for track days.Medium11112

A bolt-in diff brace such as Cusco's limits diff movement from the soft factory bushings but adds cabin noise. Recheck brakes and alignment after the engine and gearbox move.Low13

Tuning

Kits ship the ECU with a base calibration so the engine starts and the chassis functions work.

ECU approach

Standalone ECU that speaks 86 CAN, shipped with a base calibration

Sourced · medium45
Wideband

CAN wideband sensor and controller included in the complete package

Sourced · medium4

That base file is a starting point; book a calibration with wideband logging for your engine, intake and exhaust.Medium45

KPower said in 2021 it would look at a stock-ECU option for owners facing emissions tests, but the current package uses a standalone ECU only. Make ignition changes in small steps with knock monitoring and leave timing values to an experienced calibrator.Low34

Parts checklist

Tick what you have; the list is saved in this browser.

0 of 22 ticked (saved in this browser)
Mounts
Transmission
Clearance
Cooling
Fuel
Exhaust
Electrical
Chassis
Tuning
Legal

Order of work

10 stages, in the order most builds follow.

  1. Check the law and pick a block
    Confirm your local rules, then buy a K engine whose block your mount kit supports.
  2. Prepare the engine
    Fit the K20 oil pump or keep the balance-shaft pump with the matching pan, plus the intake, neck and sensors.
  3. Remove the FA20
    Support the car on rated stands and the engine on a hoist, drain fluids, then remove the boxer, driveshaft, midpipe and factory engine computer.
  4. Fit adapter and clutch
    Bolt the adapter plate and flywheel to the engine and fit a factory-style 86 clutch.
  5. Install engine and gearbox
    Fit the mount brackets, lower the assembly, and install the relocated transmission mount.
  6. Shifter and driveshaft
    Install the shifter plate and selector rod, then the one-piece driveshaft.
  7. Cooling, fuel and exhaust
    Connect the water neck, radiator and heater hoses, the fuel rail and line, and the header and midpipe.
  8. Wire the car
    Plug the engine harness into the chassis connector and install the ECU and jumper behind the glovebox.
  9. First start and checks
    Start on the base calibration and confirm gauges, ABS, cruise, climate control and fans.
  10. Calibrate and shake down
    Tune with wideband logging, then recheck mounts, driveshaft bolts and axles after the first drives.

Common problems

Symptom, cause and the usual fix.

ProblemCauseFix
Mounts do not line up with the blockKPower's brackets do not fit the K20A2, K20Z1 or K24A1 because of their left-side bolt-hole locations.Buy a listed block such as a K24A2 or K20Z3, or plan custom brackets using the kit as a starting point.Medium4
Oil pan hits the subframeA front-drive K pan sits where the 86 subframe and sway bar are.Use a rear-drive pan with the matching pump, or modify the subframe for the balance-shaft pan.Medium49
A/C compressor will not connectK24 compressors differ, and the harness is wired for the 2006-2008 TSX unit.Source the TSX compressor the harness expects, or ask the kit maker before using another.Medium4
Gearbox sits too far back for the tunnelSome adapter routes push the gearbox back far enough to hit the inner crossmember sheet metal.Follow the kit's instructions: Collins calls for reshaping that bracket, a shorter shift linkage and a new driveshaft.Medium9
Gauges and ABS warnings after the swapThe cluster, ABS and climate control expect CAN data from an engine computer.Use a computer and harness that support the 86 CAN protocol, as the complete kit does.Medium35
Automatic car cannot use the kitThe kits are designed around the 86 manual only.Convert the car to the 6-speed manual, including pedals and clutch hydraulics, before the swap.Medium3

Frequently asked

Can you keep the stock BRZ transmission with a K swap?

Yes. KPower, Collins and PMC all adapt K-series engines to the factory 86 6-speed manual. KPower moves the gearbox about 4 in back and supplies a new mount bracket, shifter plate and one-piece driveshaft. Automatic cars are not supported by the KPower kit and need converting to the manual first.Medium3910

Does a K24 fit under the stock BRZ hood?

Yes, with KPower's mounts. The company says the stock hood closes over the K24 without modification because the engine sits about 2.5 in lower and 4 in further back than the FA20. The drivetrain also clears the factory undertray. Other kits position the engine differently, so check them individually.Medium35

Do the gauges and ABS work after a K swap BRZ?

They can. The 86 cluster, ABS and climate control talk over CAN, so the new engine computer must send the right messages. KPower uses a standalone ECU that supports the 86 protocol and says gauges, climate control, ABS, cruise and traction control all work. Electric power steering needs no changes.Medium35

Which K-series engine should I use in an 86?

Use a block your mount kit lists. KPower's brackets fit the K24A2, K24A3, K24A4, JDM K24A, K20Z3, K20Z4 and K24A8, but not the K20A2, K20Z1 or K24A1. Its harness is built for 2004-2008 K24A sensors, and its test car used a stock K24A2.Medium45

Is a K swap BRZ lighter than stock?

KPower reports that it is. Weighing the same car before and after, with the same exhaust, accessories and fluids, it measured about 140 lb (64 kg) less with the K24 and its lighter parts, including A/C. The figure is the maker's own measurement on one car.Medium35

Is a K swap BRZ street legal?

It depends on where you live, and it is hard in the US. EPA expects a same-or-newer engine with its emission controls, and the K24A2 predates the 86. California requires a BAR Referee inspection, and the kits are sold for off-road use. The UK, Germany and Australia need registration updates or inspections.Medium14154161718

Related

Sources

18 sources
  1. 2013 Subaru BRZ Specifications · Subaru of America (media site) · oem · retrieved 2026-10-27
  2. Toyota 86 · Wikipedia · reference · retrieved 2026-10-27
  3. KPower 86 Swap FAQs (Jan 2021) · KPower Industries · vendor-doc · retrieved 2026-10-27
  4. KPower Complete K Swap Package for 2013-2021 Toyota/Scion/Subaru 86/FRS/BRZ (ZN6 ZC6) · KPower Industries · vendor-doc · retrieved 2026-10-27
  5. The KPower 86 Conversion Is Here (Aug 2021) · KPower Industries · vendor-doc · retrieved 2026-10-27
  6. Want to K24-Swap a Subaru BRZ, Scion FR-S or Toyota GT 86? This Kit Will Help (Aug 2021) · autoevolution · press · retrieved 2026-10-27
  7. KPower Industries is Developing a K-Series Swap Kit for the 86/FRS/BRZ · Engine Swap Depot · press · retrieved 2026-10-27
  8. Update on Pure Automotive Performance's FRS/BRZ/86 K-Series Swap Kit (Sep 2018) · Engine Swap Depot · press · retrieved 2026-10-27
  9. Honda K-Series to FRS/BRZ/FT86 Swap Kit · Collins Performance Technologies · vendor-doc · retrieved 2026-10-27
  10. Toyota GT86 / Subaru BRZ / Scion FR-S - Honda K20 K24 swap adapters · PMC Motorsport · vendor-doc · retrieved 2026-10-27
  11. Honda K engine · Wikipedia · reference · retrieved 2026-10-25
  12. OEM Subaru Rear CV Axle for 2013-2021 Subaru BRZ/Scion FR-S/Toyota 86 · Battle Garage Racing Service · vendor-doc · retrieved 2026-10-27
  13. Cusco Rear Differential Brace - 2013-2024 Subaru BRZ, Scion FR-S, Toyota 86 & GR86 · Turn In Concepts · vendor-doc · retrieved 2026-10-27
  14. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (Nov 2020) · US Environmental Protection Agency · standard · retrieved 2026-10-25
  15. Engine Changes · California Bureau of Automotive Repair · standard · retrieved 2026-10-27
  16. Change vehicle details on a V5C registration certificate (log book) · GOV.UK / DVLA · standard · retrieved 2026-10-25
  17. StVZO § 19 Erteilung und Wirksamkeit der Betriebserlaubnis · Bundesministerium der Justiz (gesetze-im-internet.de) · standard · retrieved 2026-10-25
  18. VSB 14 National Code of Practice for Light Vehicle Construction and Modification, Section LA: Engines · Queensland Department of Transport and Main Roads · standard · retrieved 2026-10-25