Injector phasing

injection timingend of injection angleEOIstart of injectionSOIinjection phase angleinjector timing

Injector phasing is the crank angle at which each injection event happens relative to the engine cycle, usually set as the end of injection angle before the intake valve opens or closes. It applies to sequential port injection and direct injection, and affects fuel film, mixture preparation, idle quality, emissions and transient response.123

How it works

Pulse width sets how much fuel is injected; phasing sets when.

Only sequential systems, which fire each injector once per cycle in step with its cylinder, can control phase precisely. That requires a cam signal so the ECU knows which stroke each cylinder is on.13

With port injection, closed-valve injection sprays fuel onto the hot back of the closed intake valve, giving it time to evaporate. Open-valve injection sends fuel straight into the cylinder with the airflow. Heywood describes how the timing changes the amount of liquid fuel reaching the cylinder and the wall film in the port.23

Many ECUs specify phasing as end of injection because the end point fixes when fuel finishes arriving relative to valve events. The start of injection then moves earlier as pulse width grows. Specifying start of injection instead means the end point drifts with load.Medium31

In direct injection, phasing is far more critical. Injection during the intake stroke gives a mostly homogeneous charge, while late injection in the compression stroke creates stratified mixtures. Spraying while the piston is close can wet the piston crown and raise particulate emissions.23

In tuning

Adjust phasing at stable conditions while watching lambda, idle stability and, where available, emissions.

Effects on port-injected engines are often small at high load and larger at idle, cold start and light load. Change one cell region at a time and keep notes, because results depend on port and spray design.Medium23

At high rpm and long pulse widths, the injection window may exceed the available crank angle. When duty approaches its limit, phasing has little room to move, which is another reason to keep injector duty within sensible limits.Medium31

Formula and worked example

Try it

ms
rpm

Result

Duty cycle81.3 %
Time per engine cycle18.46 ms

Planning estimate from the formula below, not a measurement.

Open the full injector duty cycle calculator →

Myths vs facts

Myth Batch-fire systems can be tuned for injection timing.

Fact Batch fire triggers groups of injectors together, so the timing relative to each cylinder's valve events cannot be set individually. Precise phasing needs sequential injection and cam position information.13

Myth Open-valve injection always makes more power.

Fact Results depend on port design, spray targeting and engine speed. Closed-valve injection often prepares mixture better at light load; any gain at full load must be confirmed with measurements.Medium2

Frequently asked

What is end of injection timing?

End of injection is the crank angle at which the injector pulse finishes, often referenced to intake valve opening or top dead center of the intake stroke. Setting the end point keeps fuel arrival consistent as pulse width changes; the ECU calculates the start point by subtracting the pulse duration in degrees.Medium31

Should you inject on an open or closed intake valve?

Factory port-injection calibrations commonly inject onto a closed valve at light load, because the hot valve helps vaporize fuel. Open-valve timing can reduce wall wetting in some conditions. The better choice depends on the engine, so test both against lambda stability, response and emissions data.Medium23

Does injection timing affect idle quality?

Often, yes. At idle the airflow is low and the fuel film in the port has more influence, so where the spray lands and when it evaporates changes cylinder-to-cylinder mixture. Adjusting phasing can steady idle lambda and reduce misfire on some engines.Medium23

Why does direct injection depend more on phasing?

A direct injector sprays into the cylinder, so timing decides how long fuel has to mix and where it lands. Early injection on the intake stroke gives a homogeneous charge. Late injection can stratify the mixture or wet the piston, which raises smoke and particulate emissions.23

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Fuel injection · Wikipedia · reference · retrieved 2026-10-27
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  3. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27