Valve overlap

overlapcam overlapoverlap period

Valve overlap is the period around top dead center at the end of the exhaust stroke when the intake and exhaust valves are open at the same time. It is measured in crank degrees, often at 0.050 in (1.3 mm) lift, and shapes scavenging, idle quality, manifold vacuum and residual exhaust gas.74

How it works

Valve overlap happens because the intake opens before TDC and the exhaust closes after it.

Fast-moving exhaust gas leaving the cylinder helps pull fresh charge in, which is scavenging. At high rpm this raises volumetric efficiency.76

At low rpm the same overlap hurts. Manifold pressure is below exhaust pressure, so exhaust flows back into the intake, which is reversion. The diluted charge burns slowly, idle gets rough and manifold vacuum drops.Medium34

Overlap depends on duration and lobe separation angle (LSA). Longer duration adds overlap; a wider LSA removes it. Overlap is quoted at a stated lift, usually 0.050 in, because seat-to-seat figures are much larger and vary between makers.4

Variable valve timing changes overlap on the fly. Advancing the intake cam or retarding the exhaust cam adds overlap; the opposite reduces it. That lets an engine idle smoothly yet scavenge well at high rpm.87

Typical values

Standard duration lift point0.050in1.3 mmSeat-timing figures run much largerSourced4
Overlap at 0.050 in, straight-up cam(intake + exhaust duration) / 2 minus 2 x LSAIndependent of install advanceSourced · medium43
Example: 224/230 duration on 112 LSA3 degrees overlap at 0.050 inMild street cam behaviorSourced · medium4
Road car idle speedBelow about 1,000 rpmLarge overlap makes smooth idle hardSourced · medium7

How an ECU uses it

A speed-density ECU estimates air mass from manifold pressure.

With big overlap, reversion lets exhaust into the intake, so MAP rises and pulses at idle while the cylinder actually traps less fresh air. The VE table at idle and low load must absorb that.Medium31

ECUs with VVT schedule cam targets by rpm and load, often reducing overlap at idle and light load for stability and adding it at mid-range for scavenging. Each cam position changes VE, so fuel tables or models must account for cam angle.Medium81

Overlap also creates internal exhaust gas recirculation. OEM calibrations use cam phasing to trap residual gas at part load, which lowers pumping loss and combustion temperature.Medium38

How to test it

4 checks, in order.

  1. Find the cam card figures: intake and exhaust duration at 0.050 in and the LSA. Calculate overlap and compare it with the engine's intended use before tuning idle.Medium4
  2. Degree the cam with a degree wheel and dial indicator to confirm the intake centerline. A cam installed off the card changes where overlap falls relative to TDC and changes idle and torque.Medium45
  3. Log MAP and lambda at idle. A high, pulsing MAP reading and a lambda that wanders with each cylinder event are typical of large overlap, not necessarily a vacuum leak.Low3
  4. With a vacuum gauge, compare idle vacuum before and after a cam change. A lower but steady needle suggests overlap; a fluttering or drifting needle suggests a leak or valve problem.Low41

Symptoms and causes

Rough, loping idle and low vacuum

Likely causes Large overlap, cam installed retarded

Check Check cam card overlap and degree the cam

Medium4

Rich smell and lambda swinging at idle

Likely causes Reversion and fresh charge short-circuiting into the exhaust

Check Compare lambda at idle with a higher idle speed; it should settle as overlap matters less

Low34

Poor power brakes and vacuum assist

Likely causes Low manifold vacuum from overlap

Check Measure vacuum; a reserve tank or pump may be needed

Medium4

Turbo engine feels flat off-boost after cam swap

Likely causes Overlap with exhaust pressure above boost pushes exhaust back into the cylinder

Check Log exhaust back-pressure against boost if a port is available

Low32

In tuning

On a turbo engine, overlap only scavenges when intake pressure exceeds exhaust pressure.

With a small, restrictive turbine, exhaust pressure often exceeds boost, and overlap pushes exhaust back into the cylinder. Turbo cams therefore often use less overlap or a wider LSA.Medium32

When boost does exceed exhaust pressure, overlap blows fresh air straight into the exhaust. On port injection this can add fuel to the exhaust. A wideband reads that oxygen as lean, so read lambda with care in the scavenging region.Medium34

Idle and low-load fueling on high-overlap cams need patience: raise idle speed slightly, smooth the idle VE region, and expect lambda readings to be noisy.Low31

Formula and worked example

Overlap at 0.050 in = (intake duration + exhaust duration) / 2 - 2 x LSA
intake duration
intake duration at 0.050 in liftcrank degrees
exhaust duration
exhaust duration at 0.050 in liftcrank degrees
LSA
lobe separation anglecam degrees
Medium43

Try it

°

All four events at the same checking lift, e.g. 0.050 in. Enter an event on the other side of TDC/BDC as negative.

°
°
°

Result

Lobe separation angle (cam °)110.0 °
Intake centerline (° ATDC)106.0 °
Exhaust centerline (° BTDC)114.0 °
Intake duration224.0 °
Exhaust duration230.0 °
Overlap at this lift7.0 °
Installed advance (+) or retard (−)4.0 °

Planning estimate from the formula below, not a measurement.

Open the full cam timing calculator: lobe separation, centerline and overlap →

Common mistakes

Mistake Comparing overlap figures measured at different lift points.

Do instead Compare cams only at the same lift, normally 0.050 in; seat-timing overlap is much larger.4

Mistake Chasing a lean idle reading with fuel on a big-overlap cam.

Do instead Some of the oxygen is unburned charge passing straight through; check idle speed and VE before adding fuel.Low34

Mistake Fitting a naturally aspirated high-overlap cam on a small-turbine turbo setup.

Do instead Choose a cam specified for boost, with overlap matched to the turbine's back-pressure.Medium32

Myths vs facts

Myth More overlap always makes more power.

Fact Overlap helps only when intake pressure exceeds exhaust pressure and gas speeds are high. At low rpm, or with high turbine back-pressure, it causes reversion and loses torque.43

Myth Advancing the cam reduces overlap.

Fact Advancing both lobes together on a single cam moves overlap relative to TDC but does not change its size. Only independent intake and exhaust phasing changes the amount.Medium48

Frequently asked

What is valve overlap?

Valve overlap is the crank angle around TDC at the end of the exhaust stroke when both intake and exhaust valves are open. It lets exhaust momentum pull in fresh charge at high rpm but causes reversion and rough idle at low rpm.74

How do you calculate valve overlap?

For a single cam, add intake and exhaust duration at 0.050 in, divide by two, then subtract twice the lobe separation angle. A 224/230 cam on 112 LSA has 3 degrees of overlap; on 108 LSA it has 11 degrees.Medium4

Why does a big cam idle rough?

Large overlap lets exhaust flow back into the intake at idle, because manifold pressure is lower than exhaust pressure. The diluted charge burns unevenly, so idle lopes, vacuum drops and lambda readings swing even when fueling is close to correct.Medium43

Is valve overlap bad for a turbo engine?

Not always. Overlap helps when boost exceeds exhaust back-pressure, but many turbos run higher exhaust than intake pressure, so overlap pushes exhaust back into the cylinder. Turbo cams usually use moderate overlap or a wider LSA.Medium32

How does VVT change valve overlap?

Variable valve timing shifts cam phase. Advancing the intake or retarding the exhaust adds overlap; the opposite reduces it. Engines use low overlap at idle for stability and more at mid-range for scavenging and internal EGR.Medium87

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition · Robert Bosch GmbH · book · retrieved 2026-10-27
  2. Turbo Tech 103: Expert · Garrett (Honeywell) · vendor-doc · retrieved 2026-10-27
  3. Internal Combustion Engine Fundamentals, 2nd edition (J. B. Heywood) · McGraw-Hill Education · book · retrieved 2026-10-27
  4. Camshaft · Wikipedia · reference · retrieved 2026-10-27
  5. Dead centre (engineering) · Wikipedia · reference · retrieved 2026-10-27
  6. Scavenging (engine) · Wikipedia · reference · retrieved 2026-10-27
  7. Valve timing · Wikipedia · reference · retrieved 2026-10-27
  8. Variable valve timing · Wikipedia · reference · retrieved 2026-10-27