Sensor type · Analog 0-5 V (ratiometric) · NTC thermistor

MAP sensor (1-, 2-, 3- and 4-bar)

manifold absolute pressure sensorboost sensorTMAP3 bar MAP

A MAP sensor measures absolute pressure in the intake manifold and outputs a ratiometric 0-5 V signal. The bar rating is its top of range in absolute pressure: a 1-bar sensor covers naturally aspirated vacuum, a 3-bar sensor reads about 29 psi of boost at sea level and a 4-bar about 44 psi. TMAP sensors add an intake air thermistor.231

Parts in the library

Support across ECUs

Across the 12 parts in this hub (6 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU212 configurable (generic input)
Haltech (Elite / Nexus)12 configurable (generic input)
Link (G4X)12 configurable (generic input)
MoTeC (M1)12 configurable (generic input)
ECUMaster (EMU Black)12 configurable (generic input)
AEM (Infinity)12 configurable (generic input)
MaxxECU12 configurable (generic input)
Holley (Terminator X / EFI)8 configurable (generic input) · 4 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

Inside is a piezoresistive element with on-chip amplification and temperature compensation. Bosch's PST sensors describe exactly that, with an analog ratiometric output.3

Ratiometric means output scales with the 5 V supply. Bosch gives the PST 4 as 1.143 V per bar with a -71.4 mV offset at 5 V, so 0.4 bar reads 0.386 V and 4 bar reads 4.5 V.3

A speed-density ECU uses MAP with engine speed and air temperature to estimate airflow. Range costs resolution, so pick the smallest sensor that covers your peak boost with margin.Medium1

Types and variants

1-barAnalog 0-5 V (ratiometric)

Bosch PST 1 reads 0.1-1.15 bar absolute at 4.048 V/bar: fine resolution for naturally aspirated engines.2

3-barAnalog 0-5 V (ratiometric)

Common on turbo builds up to about 2 bar of boost. GM fitted a 3-bar MAP to the supercharged LSA and LS9.Medium45

4-barAnalog 0-5 V (ratiometric)

Bosch PST 4: 0.4-4 bar absolute, 6 bar maximum. For high-boost builds.3

TMAP (pressure + temperature)NTC thermistor

Pressure and NTC air temperature in one housing; the PST sensors carry a 2,056 Ω at 25 °C thermistor on a separate pin.23

Wiring

Three wires for pressure (5 V, ground, signal) plus one for a TMAP temperature output. Bosch's PST 1 pinout: pin 1 ground, pin 2 temperature, pin 3 supply, pin 4 pressure.2

Bosch recommends an RC low-pass filter of about 2 ms at the ECU input and mounting within 60° of vertical so condensate drains away from the element.3

Connector and wiring library

Common faults and checks

Rich idle and lazy response

Likely cause Leaking or kinked vacuum hose to the sensor

Check Compare MAP at key-on, engine off, with a barometer reading; then check the hose under vacuum.Medium1

MAP flat-lines under boost

Likely cause Sensor range exceeded (1- or 2-bar sensor on a boosted engine)

Check Log MAP against a mechanical boost gauge and compare the peak to the sensor's rated range.Medium2

Sensor reads wrong after a wet wash or cold night

Likely cause Condensate in the port

Check Mount the sensor port downward within the maker's tilt limit (±60° from vertical for Bosch PST).Medium3

Frequently asked

What bar MAP sensor do I need for boost?

Add one bar (atmosphere) to your peak boost in bar and pick the next size up. A 3-bar sensor tops out near 29 psi of boost at sea level, a 4-bar near 44 psi. Larger sensors trade away resolution at idle.Medium31

What is a TMAP sensor?

A MAP sensor with an intake air temperature thermistor in the same housing. Bosch's PST sensors are examples: pressure on one pin, NTC temperature on another, sharing supply and ground.2

How do I find a MAP sensor's transfer function?

Use the maker's data sheet: Bosch publishes sensitivity and offset (1.143 V/bar and -71.4 mV for the PST 4). For OEM sensors without published data, measure two points with a calibrated pressure source and fit a line.3

Related

Use it with GAINS

MAP sensor on GAINS hardware

ECU2Internal 4-bar MAP (hose barb through the housing)

Pins
On the ECU2 pin map
Pull-up
Not used
Shielding
Not needed

No pins: an onboard 4-bar sensor reads manifold pressure through a hose. Baro is read from it at key-on before cranking.Medium6

ECU2AVI (external MAP or boost sensor)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

An external pressure sensor goes on any free AVI with the pull-up off.Medium6

The ECU2's built-in MAP is a 4-bar class sensor. A smaller external sensor on an AVI can give finer resolution for a naturally aspirated build.6

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.67

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Pressure Sensor Combined PST 1 data sheet 70513419 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. Pressure Sensor Combined PST 4 data sheet 70524939 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. OEM sensors GM Camaro: GM part numbers for Camaro knock/crank/cam/MAF/MAP/O2 sensors by year and engine (L98, LT1, LS1, LS3, LSA, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  5. GM sensors retailer catalogue: Genuine GM / Delphi / NTK / Denso / ACDelco LS and LT sensor listings with fitment titles (24x/58x crank, cam, · michiganmotorsports.com · vendor-doc · retrieved 2026-10-25
  6. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  7. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

Not yet indexed: fewer than 4 FAQs.