GM · Analog 0-5 V (ratiometric)

GM 55567257 3-bar MAP sensor (LSA / LS9)

GM 55567257GM 12592525

GM 55567257 (replacing 12592525) is the 3-bar MAP sensor GM fitted to the supercharged LSA and LS9 V8s, which makes it a common choice for boosted LS builds. GM does not publish its transfer function publicly, so calibrate it against a known pressure source rather than copying a curve from an aftermarket ECU file.Medium24

Key specifications

Measures: Absolute manifold pressure up to about 3 bar. Output: Analog 0-5 V (ratiometric).

Range class3-barabsoluteSourced · medium4
Factory fitmentLSA and LS9 supercharged V8Sourced · medium23
Transfer functionUnverifiedNot published by GM in a public document; measure two pressure points.Researched, unverified
Pinout and connectorUnverifiedNot published in a public GM document we could archive.Researched, unverified
Part numberMakerNote
55567257GMMedium24
12592525GMEarlier number, replaced by 55567257 per the GM catalogMedium24

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Any AVI (AVI1-6; pins 17-20, 14 and 26 on the ECU2): 0-5 V input with the pull-up off. Concept hardware.Medium5
Haltech (Elite / Nexus)Configurable (generic input)Analog voltage input (AVI). Haltech's wiring diagram says inputs are user definable in software; enter the maker's transfer function.89
Link (G4X)Configurable (generic input)Analogue voltage input (9 on the G4X FuryX). Link's public page does not describe how a custom calibration is entered.Medium10
MoTeC (M1)Configurable (generic input)Analogue voltage input (17 on the M150). MoTeC's sensor pages show a manual-calibration option in M1 Tune.Medium1112
ECUMaster (EMU Black)Configurable (generic input)One of 9 analog 0-5 V inputs. ECUMaster lists user-defined sensor characteristics for some functions.Medium13
AEM (Infinity)Configurable (generic input)Analog 0-5 V input (12-bit). AEM's spec sheet does not say how a custom calibration is entered.Medium14
MaxxECUConfigurable (generic input)Extra 0-5 V input (6 on the RACE). The public page does not describe calibration entry.Medium15
Holley (Terminator X / EFI)Configurable (generic input)'5' analog input, set up as a custom sensor in Holley's software (per the wiring manual).16

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

  • Parts catalogueOfficial parts-catalogue listing (no data sheet or CAD published)Medium7Download from GM Genuine PartsNo login at last check; the maker may change this

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Treat it as a 3-wire ratiometric sensor: 5 V reference, sensor ground and signal to an analog input with no pull-up. Confirm pin functions with a meter on the sensor before wiring.Medium1

Failure modes and checks

MAP reads atmospheric at idle

Likely cause Vacuum hose off or blocked

Check Check the hose and port; idle MAP should be well below barometric.Medium1

Boost reading differs from a gauge

Likely cause Calibration copied for another sensor

Check Measure two known pressures and set the slope and offset from them.Medium1

Frequently asked

What is the GM 3-bar MAP sensor part number?

55567257, which replaced 12592525 in GM's catalog. GM fitted it to the supercharged LSA and LS9.Medium24

How do I calibrate a GM 3-bar MAP without a data sheet?

Apply two known absolute pressures (for example atmosphere and a regulated boost pressure checked on a gauge), record the voltages and enter the slope and offset in the ECU. The MAP transfer calculator does the arithmetic.Medium1

Related

Use it with GAINS

GM 55567257 3-bar MAP sensor (LSA / LS9) on GAINS hardware

ECU2Internal 4-bar MAP

Pins
On the ECU2 pin map
Pull-up
Not used
Shielding
Not needed

The ECU2 has its own 4-bar MAP on a hose barb, so an external MAP is optional (finer resolution or a second pressure such as boost before the throttle).Medium5

ECU2AVI (0-5 V, pull-up off)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Any free analog input with its pull-up off; 5 V from pin 28, ground to pin 29.Medium5

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.56

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

16 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. OEM sensors GM Camaro: GM part numbers for Camaro knock/crank/cam/MAF/MAP/O2 sensors by year and engine (L98, LT1, LS1, LS3, LSA, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  3. OEM sensors GM Corvette: GM part numbers for Corvette knock/crank/cam/MAP/MAF/O2 1984-2024 (L98, LT1, LS1, LS6, LS2, LS3, LS7, LS9, LT1 · gmpartsgiant.com · oem · retrieved 2026-10-25
  4. GM sensors retailer catalogue: Genuine GM / Delphi / NTK / Denso / ACDelco LS and LT sensor listings with fitment titles (24x/58x crank, cam, · michiganmotorsports.com · vendor-doc · retrieved 2026-10-25
  5. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  6. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  7. GM Genuine Parts catalogue listing · GM Genuine Parts · oem · retrieved 2026-10-27
  8. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  9. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-10-27
  10. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  11. TMAP Sensor product page · MoTeC · vendor-doc · retrieved 2026-10-27
  12. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  13. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  14. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  15. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs; more than 40% of specs unverified.