Sensor type · NTC thermistor

Intake air temperature sensor

IAT sensorair temp sensorACT sensorcharge air temperature sensor

An intake air temperature (IAT) sensor is an NTC thermistor: its resistance falls as air gets hotter. The ECU reads it through a pull-up resistor as a voltage divider and corrects fuel for air density. Exposed-element sensors respond faster than sealed tips, which matters after an intercooler where charge temperature changes quickly.31

Parts in the library

Support across ECUs

Across the 9 parts in this hub (5 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU27 configurable (generic input) · 2 to be confirmed
Haltech (Elite / Nexus)9 configurable (generic input)
Link (G4X)7 configurable (generic input) · 2 unverified
MoTeC (M1)1 preset listed · 6 configurable (generic input) · 2 unverified
ECUMaster (EMU Black)7 configurable (generic input) · 2 unverified
AEM (Infinity)7 configurable (generic input) · 2 unverified
MaxxECU7 configurable (generic input) · 2 unverified
Holley (Terminator X / EFI)5 configurable (generic input) · 4 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

A thermistor needs a pull-up resistor to the 5 V reference inside the ECU. Bosch suggests 1 or 3 kΩ for its NTC sensors; the ECU converts the divider voltage back to temperature from the sensor's table.23

Response time drives accuracy on boosted engines. Bosch quotes under 4 s (tau 63, still water) for the small M5-HS against under 15 s for the larger M12.32

Many factory engines hide the IAT inside the MAF meter. On GM LS engines most setups had no standalone IAT, and GM rates its sensors to 250 °F.Medium5

Types and variants

Exposed (open) elementNTC thermistor

Bead in the air stream: fast, but more fragile.Medium5

Sealed tipNTC thermistor

Element inside a metal or plastic tip: slower, more robust.Medium5

In a TMAPNTC thermistor

Shares a housing and ground with the MAP sensor.4

Wiring

Two wires: signal (to an analog input with the pull-up on) and sensor ground. Polarity does not matter for a bare thermistor.Medium1

Mount the sensor where air is moving and away from hot metal: after the intercooler on boosted engines, so it reads charge temperature, not compressor outlet heat.Medium1

Connector and wiring library

Common faults and checks

IAT reads -40 °C (or the table's coldest value)

Likely cause Open circuit: no current through the thermistor, the input sits at the pull-up voltage

Check Measure sensor resistance at the plug and compare to the maker's table.Medium21

IAT reads very hot

Likely cause Short to ground, or the sensor heat-soaks from a hot manifold

Check Unplug the sensor: the reading should jump to the cold end. Then compare at a known temperature.Medium1

Frequently asked

Do IAT sensors need a pull-up resistor?

Yes. A thermistor only changes resistance; the ECU needs a pull-up to its 5 V reference to turn that into a voltage. Bosch suggests 1 or 3 kΩ for its NTC sensors, and most ECUs build it in.2

Open-element or closed IAT sensor?

Open-element sensors react faster to changing air temperature, which suits boosted and fast-changing intakes. Closed sensors survive better but lag. Bosch's small M5-HS quotes under 4 s response against under 15 s for the M12.Medium325

Where should the IAT go on a turbo car?

After the intercooler, close to the throttle, so it reads the charge temperature that actually enters the engine.Medium1

Related

Use it with GAINS

Intake air temperature sensor on GAINS hardware

ECU2AVI (thermistor, pull-up on)

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

Any AVI with its pull-up enabled. In the K20 drive-by-wire example the IAT uses AVI6 on pin 26, which puts the wideband on a nominal calibration.Medium6

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.67

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Temperature Sensor NTC M12 data sheet 70101387 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. Temperature Sensor NTC M5-HS data sheet 70019083 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. Pressure Sensor Combined PST 1 data sheet 70513419 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  5. Dialing in LS sensors for various generations with Michigan Motorsports · EngineLabs · press · retrieved 2026-10-27
  6. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  7. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

Not yet indexed: fewer than 4 FAQs.