GM · NTC thermistor

GM 12160244 intake air temperature sensor (LS1)

GM 12160244

GM 12160244 is the LS1-era push-in intake air temperature sensor. EngineLabs notes most LS engines hid the IAT inside the MAF, that this press-in sensor suits naturally aspirated and mild boost builds, and that GM rates its IAT sensors to 250 °F (121 °C). Later threaded GM sensors with an exposed element respond faster.Medium32

Key specifications

Measures: Intake air temperature. Output: NTC thermistor.

MountingPress-ingrommetSourced · medium3
Rated temperature250°F121 °CSourced · medium3
Resistance tableUnverifiedNot in a public GM document we could archive.Researched, unverified
Part numberMakerNote
12160244GMMedium23

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)AVI with the switchable pull-up on (AVI5, pin 14, is the default coolant input). Concept hardware.Medium4
Haltech (Elite / Nexus)Configurable (generic input)AVI with its software-selectable 1 kΩ pull-up to 5 V switched on; enter the maker's resistance table.Medium7
Link (G4X)Configurable (generic input)Temperature input with the selectable pull-up switched on (4 on the FuryX). Pull-up value not stated for G4X.8
MoTeC (M1)Configurable (generic input)Analogue temperature input (1 kΩ pull-up to sensor 5 V per the M150 pinout).9
ECUMaster (EMU Black)Configurable (generic input)Temperature sensor input (IAT, CLT and oil temperature are listed). Pull-up value not stated publicly.Medium10
AEM (Infinity)Configurable (generic input)Analog temperature input (2.49 kΩ pull-up to 5 V per the Series 5 spec).11
MaxxECUConfigurable (generic input)Temperature input (2 extra on the RACE). Pull-up value not on the public pages.Medium12
Holley (Terminator X / EFI)Configurable (generic input)Thermistor 'T' input for two-wire temperature sensors. Pull-up value not stated.13

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

  • Parts catalogueOfficial parts-catalogue listing (no data sheet or CAD published)Medium6Download from GM Genuine PartsNo login at last check; the maker may change this

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Two wires to an analog input with pull-up and sensor ground. Fit it in moving air, after the intercooler on boosted builds.Medium1

Failure modes and checks

Air temperature lags

Likely cause Sealed-tip sensor or heat-soaked location

Check Move the sensor into the air stream or use an exposed-element type.Medium3

Sensor pops out under boost

Likely cause Press-in grommet on a high-boost intake

Check Use a threaded sensor for higher boost.Medium3

Frequently asked

What IAT sensor does an LS1 use?

GM 12160244, a press-in sensor; many later LS engines put the IAT inside the MAF instead.Medium32

Is the GM push-in IAT OK for boost?

EngineLabs suggests it for naturally aspirated and mild boost builds; a threaded sensor is the safer choice for more boost.Medium3

Related

Use it with GAINS

GM 12160244 intake air temperature sensor (LS1) on GAINS hardware

ECU2AVI (thermistor, pull-up on)

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

Any free analog input with its pull-up switched on.Medium4

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.45

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

13 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. GM sensors retailer catalogue: Genuine GM / Delphi / NTK / Denso / ACDelco LS and LT sensor listings with fitment titles (24x/58x crank, cam, · michiganmotorsports.com · vendor-doc · retrieved 2026-10-25
  3. Dialing in LS sensors for various generations with Michigan Motorsports · EngineLabs · press · retrieved 2026-10-27
  4. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  5. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  6. GM Genuine Parts catalogue listing · GM Genuine Parts · oem · retrieved 2026-10-27
  7. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  8. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  9. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  10. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  11. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  12. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.