Bosch · NTC thermistor
Bosch NTC M5-HS fast temperature sensor
The Bosch NTC M5-HS is a small, fast thermistor for air, oil, water or fuel from -55 to 300 °C. It is a 10 kΩ ± 1 % at 25 °C element in a stainless M5 housing, responds in under 4 s (still water) and suits charge-air temperature after an intercooler. Bosch suggests a 1 or 3 kΩ pull-up.2
Key specifications
Measures: Air or fluid temperature. Output: NTC thermistor.
| Part number | Maker | Note |
|---|---|---|
| NTC M5-HS (data sheet 70019083) | Bosch Motorsport | Order number per wire length and connector2 |
Pinout and connector
- Supply
- Ground / return
- Signal
- Shield
- Not used / not listed
| Pin | Function (as published) | Typical ECU input | Wire note |
|---|---|---|---|
| 1 | Not used | Leave unconnected | — |
| 2 | SIG− | Sensor ground | Return to sensor ground, not chassis |
| 3 | SIG+ | Temperature input (pull-up on) | — |
| 4 | Not used | Leave unconnected | — |
| 5 | Not used | Leave unconnected | — |
Connector version ASL606-05PN-HE, per the Bosch product page.Medium5 The ECU-input and wire columns are our general guidance, not the maker's.
Connector: ASL606-05PN-HE (Autosport); mating part ASL006-05SN-HE25 Connector library
Terminals and seals: Not listed: the Bosch data sheet gives the mating housing only, not contact or seal part numbers.
Transfer function and calibration data
Show the 26 data points
| Temperature (°C) | Resistance (Ω) |
|---|---|
| -55 | 519,910 |
| -35 | 158,090 |
| -20 | 71,668 |
| -10 | 44,087 |
| 0 | 27,936 |
| 10 | 18,187 |
| 20 | 12,136 |
| 25 | 10,000 |
| 30 | 8,284 |
| 40 | 5,774 |
| 50 | 4,103 |
| 60 | 2,967 |
| 70 | 2,182 |
| 80 | 1,629 |
| 90 | 1,234 |
| 100 | 946.6 |
| 120 | 578.1 |
| 140 | 368.8 |
| 160 | 244.4 |
| 180 | 167.6 |
| 200 | 118.5 |
| 220 | 86.08 |
| 240 | 64.08 |
| 260 | 48.76 |
| 280 | 37.86 |
| 300 | 29.94 |
How it's calibrated
ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.
Transfer function
- NTC: 519,910 Ω at -55 °C falling to 29.9 Ω at 300 °C2
- Steinhart-Hart fit through -55 °C, 80 °C, 300 °C: A = 8.5737e-4, B = 2.5947e-4, C = 1.3667e-7 (largest error against the maker's table 0.56 °C).2Calculated from the maker's data
Worked conversion
- At 25 °C the element is 10,000 Ω; with a 1 kΩ pull-up to 5 V the ECU sees 5 × 10,000 / (10,000 + 1,000) = 4.545 V.2Calculated from the maker's data
Resistance vs temperature: resistance and ECU input voltage (26 rows)Calculated from the maker's data
| Temperature (°C) | Resistance (Ω) | V at 1 kΩ pull-up to 5 V | V at 2.2 kΩ pull-up to 5 V |
|---|---|---|---|
| -55 | 519910 | 4.99 | 4.979 |
| -35 | 158090 | 4.969 | 4.931 |
| -20 | 71668 | 4.931 | 4.851 |
| -10 | 44087 | 4.889 | 4.762 |
| 0 | 27936 | 4.827 | 4.635 |
| 10 | 18187 | 4.739 | 4.46 |
| 20 | 12136 | 4.619 | 4.233 |
| 25 | 10000 | 4.545 | 4.098 |
| 30 | 8284 | 4.461 | 3.951 |
| 40 | 5774 | 4.262 | 3.621 |
| 50 | 4103 | 4.02 | 3.255 |
| 60 | 2967 | 3.74 | 2.871 |
| 70 | 2182 | 3.429 | 2.49 |
| 80 | 1629 | 3.098 | 2.127 |
| 90 | 1234 | 2.762 | 1.797 |
| 100 | 946.6 | 2.431 | 1.504 |
| 120 | 578.1 | 1.832 | 1.04 |
| 140 | 368.8 | 1.347 | 0.718 |
| 160 | 244.4 | 0.982 | 0.5 |
| 180 | 167.6 | 0.718 | 0.354 |
| 200 | 118.5 | 0.53 | 0.256 |
| 220 | 86.08 | 0.396 | 0.188 |
| 240 | 64.08 | 0.301 | 0.142 |
| 260 | 48.76 | 0.232 | 0.108 |
| 280 | 37.86 | 0.182 | 0.085 |
| 300 | 29.94 | 0.145 | 0.067 |
Resistance from the maker's table. The maker does not state a pull-up; 1 kΩ and 2.2 kΩ are example values: use your ECU's actual pull-up.
Native support across ECUs
| ECU platform | Status | How to set it up | Source |
|---|---|---|---|
| GAINS ECU2Concept | Configurable (generic input) | AVI with the switchable pull-up on (AVI5, pin 14, is the default coolant input). Concept hardware. | Medium3 |
| Haltech (Elite / Nexus) | Configurable (generic input) | AVI with its software-selectable 1 kΩ pull-up to 5 V switched on; enter the maker's resistance table. | Medium7 |
| Link (G4X) | Configurable (generic input) | Temperature input with the selectable pull-up switched on (4 on the FuryX). Pull-up value not stated for G4X. | 8 |
| MoTeC (M1) | Configurable (generic input) | Analogue temperature input (1 kΩ pull-up to sensor 5 V per the M150 pinout). | 9 |
| ECUMaster (EMU Black) | Configurable (generic input) | Temperature sensor input (IAT, CLT and oil temperature are listed). Pull-up value not stated publicly. | Medium10 |
| AEM (Infinity) | Configurable (generic input) | Analog temperature input (2.49 kΩ pull-up to 5 V per the Series 5 spec). | 11 |
| MaxxECU | Configurable (generic input) | Temperature input (2 extra on the RACE). Pull-up value not on the public pages. | Medium12 |
| Holley (Terminator X / EFI) | Configurable (generic input) | Thermistor 'T' input for two-wire temperature sensors. Pull-up value not stated. | 13 |
Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.
Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.
CAD and drawings
- Data sheetTemperature Sensor NTC M5-HS data sheet 70019083 (PDF)2Download from Bosch MotorsportNo login at last check; the maker may change this
- DrawingOffer drawing56Download from Bosch MotorsportNo login at last check; the maker may change this
- 3D CAD3D data (zip)56Download from Bosch MotorsportNo login at last check; the maker may change this
We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.
Wiring and installation
Two signal wires to an analog input with pull-up and to sensor ground. A 10 kΩ element pairs best with a pull-up near its working-range resistance; Bosch suggests 1 or 3 kΩ.Medium2
Failure modes and checks
Likely cause Slow sensor or poor location
Check Use a fast element like the M5-HS in the air stream after the intercooler.Medium2
Test it with a multimeter
- Unplugged, measure resistance across the two element pins: about 10,000 Ω at 25 °C, falling as it warms (compare with the table).2Calculated from the maker's data
Frequently asked
Related
Use it with GAINS
Bosch NTC M5-HS fast temperature sensor on GAINS hardware
GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34
Concept Pre-release hardware. Pin assignments come from the current design documents and may change.
Sources
13 sources
- Temperature Sensor NTC M12 data sheet 70101387 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
- Temperature Sensor NTC M5-HS data sheet 70019083 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
- internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
- internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
- NTC M5 HS product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
- Bosch Motorsport legal notice · Bosch Motorsport (Robert Bosch GmbH) · vendor-doc · retrieved 2026-10-27
- Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
- G4X FuryX product page · Link Engine Management · vendor-doc · retrieved 2026-10-27
- M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
- EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
- Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
- MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
- HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27
Not yet indexed: fewer than 3 FAQs.

