Sensor type · NTC thermistor

Oil temperature sensor

oil temp sensoroil temperature senderengine oil temperature sensor

An oil temperature sensor is an NTC thermistor in the sump, filter adapter or oil cooler line. It is wired like a coolant sensor but needs a higher range: Bosch's NTC M12-H covers -40 to 150 °C and reads 57 Ω at 150 °C, where a coolant-range sensor stops at 130 °C.21

Parts in the library

Support across ECUs

Across the 3 parts in this hub (3 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU23 configurable (generic input)
Haltech (Elite / Nexus)3 configurable (generic input)
Link (G4X)3 configurable (generic input)
MoTeC (M1)1 preset listed · 2 configurable (generic input)
ECUMaster (EMU Black)3 configurable (generic input)
AEM (Infinity)3 configurable (generic input)
MaxxECU3 configurable (generic input)
Holley (Terminator X / EFI)3 configurable (generic input)

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

Oil runs hotter than coolant under sustained load, so the sensor's table must extend past the highest oil temperature you expect.Medium2

A higher-accuracy sensor helps at the top of the range: Bosch quotes ±0.8 °C at 100 °C for the M12-H against ±3.4 °C for the standard M12.21

Types and variants

Thermistor to 150 °CNTC thermistor

NTC M12-H: M12x1.5, aluminium washer, 18 N·m.2

Small fast thermistor to 300 °CNTC thermistor

NTC M5-HS: 10 kΩ at 25 °C, M5 thread, under 4 s response.3

Wiring

Two wires to an analog input with the pull-up on and to sensor ground. Bosch suggests a 1 or 3 kΩ pull-up.2

Connector and wiring library

Common faults and checks

Oil temperature reads the coldest value

Likely cause Open circuit or unplugged sensor

Check Measure resistance at the connector against the maker's table.Medium2

Reading stops rising at high load

Likely cause Table or sensor range ends below real oil temperature

Check Check the sensor's rated range and the ECU table's top point.Medium12

Frequently asked

What oil temperature sensor range do I need?

One that reaches past your hottest expected oil temperature. Bosch's NTC M12 stops at 130 °C; the M12-H goes to 150 °C and the M5-HS to 300 °C.123

Can I use a coolant sensor for oil temperature?

Only if its range covers your oil temperatures. Bosch's M12 and M12-H share the same table to 130 °C, but only the M12-H is specified to 150 °C.12

Does an oil temperature sensor need a pull-up?

Yes, like any thermistor. Bosch suggests 1 or 3 kΩ.2

Related

Use it with GAINS

Oil temperature sensor on GAINS hardware

ECU2AVI (thermistor, pull-up on)

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

Any free AVI with the pull-up on.Medium4

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.45

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Temperature Sensor NTC M12 data sheet 70101387 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  2. Temperature Sensor NTC M12-H data sheet 70115595 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. Temperature Sensor NTC M5-HS data sheet 70019083 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  5. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

Not yet indexed: fewer than 4 FAQs.