Sensor type · Analog 0-5 V (ratiometric)

Oil pressure sensor

oil pressure senderoil pressure transducerOPS

An oil pressure sensor is a 3-wire transducer that outputs 0.5-4.5 V in proportion to pressure, so an ECU or logger can warn or cut power when pressure drops. Factory oil pressure switches only close at one threshold. Bosch's PSS-10 is a typical sensor: 1-11 bar absolute, 400 mV per bar, 100 mV offset at 5 V supply.21

Parts in the library

Support across ECUs

Across the 3 parts in this hub (1 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU23 configurable (generic input)
Haltech (Elite / Nexus)3 configurable (generic input)
Link (G4X)3 configurable (generic input)
MoTeC (M1)3 configurable (generic input)
ECUMaster (EMU Black)3 configurable (generic input)
AEM (Infinity)3 configurable (generic input)
MaxxECU3 configurable (generic input)
Holley (Terminator X / EFI)2 configurable (generic input) · 1 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

A stainless measuring cell with a piezoresistive bridge, welded to the pressure port, makes the sensor compatible with oil, fuel and coolant.2

Absolute sensors read 1 bar with the engine off; gauge (relative) sensors read zero. Subtract barometric pressure from an absolute reading for gauge oil pressure.Medium23

Types and variants

Absolute (bar a)Analog 0-5 V (ratiometric)

PSS-10: 1-11 bar absolute, 20 bar maximum.2

Relative / gauge (bar g)Analog 0-5 V (ratiometric)

Reads zero at atmosphere; PST-F 1 is an example for fuel.3

Pressure switch

Closes or opens at one pressure; drives a warning lamp only.Medium1

Wiring

Bosch's PSS-10 pinout on its 3-pole Compact connector: pin 1 ground, pin 2 signal, pin 3 supply. Bosch advises against bolting the sensor directly to the engine block to limit vibration.2

Mount remote sensors on a short braided line and a bracket; a long line can damp fast pressure drops.Medium1

Connector and wiring library

Common faults and checks

Reading pegged at maximum

Likely cause Signal shorted to 5 V or open ground

Check Measure supply and ground at the plug, then the signal with the engine off.Medium2

Reading noisy at high rpm

Likely cause Vibration or a cracked fitting

Check Move the sensor to a remote mount; Bosch advises against fixing the PSS-10 straight to the block.Medium2

Frequently asked

How do I wire a 0-5 V oil pressure sensor?

Three wires: 5 V reference, sensor ground and signal to an analog input with no pull-up. On Bosch's PSS-10 those are pins 3, 1 and 2 of a 3-pole Compact connector.2

Absolute or gauge sensor for oil pressure?

Either works. An absolute sensor reads about 1 bar with the engine off, so subtract barometric pressure to display gauge pressure. A gauge sensor reads zero at rest.Medium23

Can the ECU protect the engine on low oil pressure?

With a proportional sensor it can compare pressure to an rpm-based minimum and warn or limit power. A factory switch only reports one threshold.Medium1

Related

Use it with GAINS

Oil pressure sensor on GAINS hardware

ECU2AVI (0-5 V, pull-up off)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

The cable-throttle example uses AVI4 for oil pressure.Medium4

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.45

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Pressure Sensor Fluid PSS-10 data sheet 69547659 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. Pressure Sensor Combined PST-F 1 data sheet 70496907 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  5. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

Not yet indexed: fewer than 4 FAQs.