GM · Analog 0-5 V (ratiometric)

GM 12677836 oil pressure sensor (LS)

GM 12677836

GM 12677836 is an LS oil pressure sensor that sits on the back of the valley cover behind the intake manifold. EngineLabs notes three oil pressure sensor variants exist across LS years and models with different connectors, and that they are not tied to Gen III or Gen IV. GM does not publish its transfer function publicly.Medium2

Key specifications

Measures: Engine oil pressure. Output: Analog 0-5 V (ratiometric).

LocationBack of the valley cover, behind the intake manifoldSourced · medium2
VariantsThree variants with different connectors across LS yearsSourced · medium2
Transfer functionUnverifiedNot in a public GM document we could archive.Researched, unverified
PinoutUnverifiedResearched, unverified
Part numberMakerNote
12677836GMMedium2

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Any AVI (AVI1-6; pins 17-20, 14 and 26 on the ECU2): 0-5 V input with the pull-up off. Concept hardware.Medium3
Haltech (Elite / Nexus)Configurable (generic input)Analog voltage input (AVI). Haltech's wiring diagram says inputs are user definable in software; enter the maker's transfer function.67
Link (G4X)Configurable (generic input)Analogue voltage input (9 on the G4X FuryX). Link's public page does not describe how a custom calibration is entered.Medium8
MoTeC (M1)Configurable (generic input)Analogue voltage input (17 on the M150). MoTeC's sensor pages show a manual-calibration option in M1 Tune.Medium910
ECUMaster (EMU Black)Configurable (generic input)One of 9 analog 0-5 V inputs. ECUMaster lists user-defined sensor characteristics for some functions.Medium11
AEM (Infinity)Configurable (generic input)Analog 0-5 V input (12-bit). AEM's spec sheet does not say how a custom calibration is entered.Medium12
MaxxECUConfigurable (generic input)Extra 0-5 V input (6 on the RACE). The public page does not describe calibration entry.Medium13
Holley (Terminator X / EFI)Configurable (generic input)'5' analog input, set up as a custom sensor in Holley's software (per the wiring manual).14

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

  • Parts catalogueOfficial parts-catalogue listing (no data sheet or CAD published)Medium5Download from GM Genuine PartsNo login at last check; the maker may change this

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Wire as a 3-wire ratiometric sensor once pin functions are confirmed with a meter.Low1

Failure modes and checks

No oil pressure reading after a swap

Likely cause Connector variant mismatch

Check Match the sensor to the harness connector; there are three LS variants.Medium2

Reading differs from a mechanical gauge

Likely cause Calibration copied from another sensor

Check Calibrate against a mechanical gauge at two pressures.Medium1

Frequently asked

Where is the oil pressure sensor on an LS?

On the back of the valley cover, behind the intake manifold, on both Gen III and Gen IV engines.Medium2

Why doesn't my LS oil pressure sensor plug in?

LS engines used three oil pressure sensor variants with different connectors across years and models.Medium2

Related

Use it with GAINS

GM 12677836 oil pressure sensor (LS) on GAINS hardware

ECU2AVI (0-5 V, pull-up off)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Any free analog input with its pull-up off; 5 V from pin 28, ground to pin 29.Medium3

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

14 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Dialing in LS sensors for various generations with Michigan Motorsports · EngineLabs · press · retrieved 2026-10-27
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  5. GM Genuine Parts catalogue listing · GM Genuine Parts · oem · retrieved 2026-10-27
  6. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  7. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-10-27
  8. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  9. TMAP Sensor product page · MoTeC · vendor-doc · retrieved 2026-10-27
  10. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  11. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  12. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  13. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs; more than 40% of specs unverified.