Bosch · Analog 0-5 V (ratiometric)

Bosch PSS-10 fluid pressure sensor (1-11 bar abs)

Bosch Motorsport B261.209.341-01

The Bosch PSS-10 (B261.209.341-01) is an absolute pressure sensor for oil, fuel, water or air from 1 to 11 bar. Output is 10-90 % of the 5 V supply: 400 mV per bar with a 100 mV offset, so 1 bar reads 0.5 V and 11 bar reads 4.5 V. Pins 1 ground, 2 signal, 3 supply on a 3-pole Compact connector.1

Key specifications

Measures: Absolute fluid pressure (1-11 bar). Output: Analog 0-5 V (ratiometric).

Range
  • 1-11 bar absolute
  • 20 bar maximum
Sourced1
Output10-90 % of supply, ratiometricSourced1
Sensitivity / offset
  • 400 mV/bar
  • 100 mV at 5 V
Sourced1
Tolerance± 0.1 bar (± 1 % FS), compensated 0-90 °CSourced1
Media
  • Diesel, gasoline, water, engine and gearbox oil, air
  • E85 / M100
Sourced1
Thread / torqueM10x1, 17 mm, 15 N·m, O-ring 7.65 × 1.63 mmSourced1
ProtectionOvervoltage, reverse polarity, short circuitSourced1
Part numberMakerNote
B261.209.341-01Bosch Motorsport1

Pinout and connector

123Schematic, pin-number order (positions not published)
Schematic in pin-number order: the maker does not publish cavity positions. Mating face labels. Pin functions from the maker's document. Our drawing from the published pin list, not a maker drawing.
  • Supply
  • Ground / return
  • Signal
  • Shield
  • Not used / not listed
Download pinout (SVG)
PinFunction (as published)Typical ECU inputWire note
1GroundSensor groundReturn to sensor ground, not chassis
2SignalAnalog voltage input (pull-up off)—
3Supply (5 V)+5 V sensor reference—

Pin functions as published.1 The ECU-input and wire columns are our general guidance, not the maker's.

Connector: Bosch Compact 3-pole; mating part D261.205.339-011 Connector library

Terminals and seals: Not listed: the Bosch data sheet gives the mating housing only, not contact or seal part numbers.

Transfer function and calibration data

Pressure transfer at 5 V1

Ua = 0.1 V + 0.4 V/bar × p (at Us = 5 V)

0.51.52.53.54.513.568.511Absolute pressure (bar)Output (V)

Points computed from Bosch's sensitivity and offset.

Show the 6 data points
Absolute pressure (bar)Output (V)
10.5
31.3
52.1
72.9
93.7
114.5

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Transfer function

  • 0.5–4.5 V → 100–1,100 kPa absolute (maker: Ua = 0.1 V + 0.4 V/bar × p (at Us = 5 V))1Calculated from the maker's data

Worked conversion

  • At 2.5 V the maker's transfer line gives 600 kPa absolute (87 psia).1Calculated from the maker's data
Pressure transfer at 5 V: output voltage to pressure (17 rows)Calculated from the maker's data
Output (V)Pressure (kPa absolute)Pressure (psia)
0.510014.5
0.75162.523.57
122532.63
1.25287.541.7
1.535050.76
1.75412.559.83
247568.89
2.25537.577.96
2.560087.02
2.75662.596.09
3725105.15
3.25787.5114.22
3.5850123.28
3.75912.5132.35
4975141.41
4.251037.5150.48
4.51100159.54

Interpolated between the maker's published points; nominal values with no tolerance band.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Any AVI (AVI1-6; pins 17-20, 14 and 26 on the ECU2): 0-5 V input with the pull-up off. Concept hardware.Medium2
Haltech (Elite / Nexus)Configurable (generic input)Analog voltage input (AVI). Haltech's wiring diagram says inputs are user definable in software; enter the maker's transfer function.67
Link (G4X)Configurable (generic input)Analogue voltage input (9 on the G4X FuryX). Link's public page does not describe how a custom calibration is entered.Medium8
MoTeC (M1)Configurable (generic input)Analogue voltage input (17 on the M150). MoTeC's sensor pages show a manual-calibration option in M1 Tune.Medium910
ECUMaster (EMU Black)Configurable (generic input)One of 9 analog 0-5 V inputs. ECUMaster lists user-defined sensor characteristics for some functions.Medium11
AEM (Infinity)Configurable (generic input)Analog 0-5 V input (12-bit). AEM's spec sheet does not say how a custom calibration is entered.Medium12
MaxxECUConfigurable (generic input)Extra 0-5 V input (6 on the RACE). The public page does not describe calibration entry.Medium13
Holley (Terminator X / EFI)Configurable (generic input)'5' analog input, set up as a custom sensor in Holley's software (per the wiring manual).14

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Mount it off the engine block on a bracket and short line; Bosch advises against fixing it directly to the block because of vibration.1

Failure modes and checks

Reads about 1 bar with the engine off

Likely cause Normal: it is an absolute sensor

Check Subtract barometric pressure for gauge oil pressure.Medium1

Signal noisy or sensor fails early

Likely cause Mounted directly on the block

Check Remote-mount as Bosch advises.Medium1

Test it with a multimeter

  • Key on, engine off, port open to air: back-probe signal to sensor ground and expect about 0.51 V; the supply pin should read the ECU's 5 V reference.1Calculated from the maker's data

Frequently asked

What is the output of the Bosch PSS-10?

0.5 V at 1 bar absolute rising 0.4 V per bar to 4.5 V at 11 bar, with a 5 V supply.1

Can the PSS-10 measure fuel pressure?

Yes. Bosch lists diesel, gasoline, E85 and M100 among compatible media. Remember it reads absolute pressure.1

Related

Use it with GAINS

Bosch PSS-10 fluid pressure sensor (1-11 bar abs) on GAINS hardware

ECU2AVI (0-5 V, pull-up off)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Any free analog input with its pull-up off; 5 V from pin 28, ground to pin 29.Medium2

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.23

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

14 sources
  1. Pressure Sensor Fluid PSS-10 data sheet 69547659 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  2. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  3. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  4. PSS 10 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  5. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  6. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-10-27
  7. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  8. TMAP Sensor product page · MoTeC · vendor-doc · retrieved 2026-10-27
  9. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  10. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  11. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  12. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.