Sensor type · Analog 0-5 V (ratiometric) · NTC thermistor

Fuel pressure sensor

fuel pressure transducerFPSfuel rail pressure sensor (port injection)

A port-injection fuel pressure sensor reports rail pressure as 0.5-4.5 V so the ECU can compensate injector flow or flag a failing pump. Bosch's PST-F 1 reads 0-10 bar relative at 400 mV per bar plus 500 mV, and adds a fuel temperature thermistor on a separate pin.3

Parts in the library

Support across ECUs

Across the 3 parts in this hub (2 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU23 configurable (generic input)
Haltech (Elite / Nexus)3 configurable (generic input)
Link (G4X)3 configurable (generic input)
MoTeC (M1)3 configurable (generic input)
ECUMaster (EMU Black)3 configurable (generic input)
AEM (Infinity)3 configurable (generic input)
MaxxECU3 configurable (generic input)
Holley (Terminator X / EFI)2 configurable (generic input) · 1 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

Injector flow depends on the pressure across the injector, rail pressure minus manifold pressure. A relative sensor referenced to atmosphere plus the MAP signal lets the ECU compute that difference.Medium31

Combined sensors add fuel temperature, which the ECU can use for density compensation, especially with ethanol blends.3

Types and variants

Relative (gauge)Analog 0-5 V (ratiometric)

PST-F 1: 0-10 bar relative, burst 40 bar, sealed-cone M10x1 port.3

AbsoluteAnalog 0-5 V (ratiometric)

PSS-10: 1-11 bar absolute; subtract baro for gauge pressure.2

Wiring

PST-F 1 pinout on its Bosch Trapezoid connector: pin 2 pressure, pin 3 supply, pin 4 ground, pin 5 temperature. Bosch suggests a 4.6 kΩ pull-up for the temperature channel.3

Fuel system work carries fire risk: depressurise the rail, use fuel-rated fittings and check for leaks with the pump primed before starting.Medium1

Connector and wiring library

Common faults and checks

Lean under load while pressure looks normal at idle

Likely cause Pump or regulator cannot hold pressure at flow

Check Log fuel pressure against MAP at full load; the difference should stay at the regulator's set point.Medium1

Pressure reading drifts with temperature

Likely cause Wrong pull-up on the temperature channel or a damaged sensor

Check Check the temperature channel against the maker's table with a 4.6 kΩ pull-up (Bosch PST-F 1).Medium3

Frequently asked

Should a fuel pressure sensor be absolute or relative?

Either, as long as the ECU knows which. Injector flow depends on rail minus manifold pressure, so the ECU needs MAP as well. A relative sensor reads zero at atmosphere; an absolute sensor reads about 1 bar.Medium32

Where should a fuel pressure sensor go?

On the rail, or at the rail's feed, so it reads the pressure the injectors see. A sensor at the pump outlet misses losses in the line and filter.Medium1

What does the temperature pin on a combined fuel sensor do?

It carries an NTC thermistor so the ECU can correct for fuel density. On Bosch's PST-F 1 it is pin 5, read with a 4.6 kΩ pull-up.3

Related

Use it with GAINS

Fuel pressure sensor on GAINS hardware

ECU2AVI (pressure, pull-up off; temperature, pull-up on)

Pins
On the ECU2 pin map
Pull-up
To be confirmed
Shielding
Not needed

Pressure and temperature need two AVI inputs. The cable-throttle example frees AVI inputs; a drive-by-wire build may need the PDM2 for extra channels.Medium4

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.45

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Pressure Sensor Fluid PSS-10 data sheet 69547659 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. Pressure Sensor Combined PST-F 1 data sheet 70496907 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  5. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

Not yet indexed: fewer than 4 FAQs.