Sensor type · Analog 0-5 V (ratiometric)

Direct-injection rail pressure sensor

DI rail pressure sensorhigh pressure fuel sensorGDI fuel pressure sensor

A direct-injection rail pressure sensor measures fuel pressure in the high-pressure rail, typically hundreds of bar, so the ECU can control the cam-driven pump and calculate injector flow. Bosch's PSS-260 reads 0-260 bar absolute with a 0.5-4.5 V ratiometric output, 15.38 mV per bar plus 500 mV at 5 V.2

Parts in the library

Support across ECUs

Across the 4 parts in this hub (4 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU22 configurable (generic input) · 2 to be confirmed
Haltech (Elite / Nexus)4 configurable (generic input)
Link (G4X)4 configurable (generic input)
MoTeC (M1)4 configurable (generic input)
ECUMaster (EMU Black)4 configurable (generic input)
AEM (Infinity)4 configurable (generic input)
MaxxECU4 configurable (generic input)
Holley (Terminator X / EFI)2 configurable (generic input) · 2 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

Gasoline direct injection sprays fuel straight into the cylinder at high pressure, so rail pressure is a closed-loop control target rather than a fixed regulator setting.Medium7

These sensors use a steel diaphragm or stainless measuring cell with strain gauges or piezoresistive bridges, sealed by a cone seat in the rail.42

Types and variants

Pressure onlyAnalog 0-5 V (ratiometric)

PSS-260: 0-260 bar absolute, 320 bar maximum, M10x1 sealed cone.2

Pressure + temperatureAnalog 0-5 V (ratiometric)

PST-F 2 280 bar: 0-280 bar absolute plus a 10 kΩ at 25 °C NTC.4

Wiring

Three wires for pressure: Bosch's PSS-260 uses pin 1 ground, pin 2 signal, pin 3 supply on a 3-pole Compact connector. Torque to the maker's value for the rail material.2

High-pressure fuel can cause injury and fire: never open a DI rail with the system pressurised.Medium1

Connector and wiring library

Common faults and checks

Rail pressure does not follow target

Likely cause Pump control, sensor or wiring fault

Check Compare sensor voltage at key-on, engine off, against the expected low-pressure value before blaming the pump.Medium2

Seep at the sensor

Likely cause Sealing cone damaged or torque wrong

Check Replace and torque to specification (PSS-260: 22 N·m in aluminium, 32.5 N·m in steel).Medium2

Frequently asked

What voltage does a rail pressure sensor output?

Usually 0.5-4.5 V ratiometric. On Bosch's PSS-260, voltage = 0.5 V + 15.38 mV × pressure in bar at 5 V supply, so 100 bar reads about 2.04 V.2

Why does direct injection need a rail pressure sensor?

Because rail pressure changes with demand and is controlled by the high-pressure pump. The ECU needs the actual value both to close the pump loop and to compute how much fuel each injection delivers.Medium71

Can I use a port-injection fuel sensor on a DI rail?

No. Port sensors are rated around 10 bar; DI rails run hundreds of bar. Use a sensor rated for the rail's maximum pressure, such as the 260 bar PSS-260.32

Related

Use it with GAINS

Direct-injection rail pressure sensor on GAINS hardware

ECU2AVI (0-5 V, pull-up off)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Readable as an analog channel; direct-injection drive itself is outside the ECU2's scope.Medium5

DIRail pressure for the DI driver

Pins
No pins
Pull-up
To be confirmed
Shielding
Not needed

The DI is a direct-injection driver module; its rail-pressure input assignment is not published yet.Low5

Direct injection is a separate driver module in the GAINS lineup and is roadmap work, not shipping.Medium5

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.56

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Pressure Sensor Fluid PSS-260 data sheet 411837451 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. Pressure Sensor Combined PST-F 1 data sheet 70496907 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  4. Pressure Sensor Combined PST-F 2 280 bar data sheet 70473483 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  5. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  6. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  7. Gasoline direct injection · Wikipedia · reference · retrieved 2026-10-27

Not yet indexed: fewer than 4 FAQs.