Bosch · Analog 0-5 V (ratiometric)

Bosch PSS-260 DI rail pressure sensor (260 bar)

Bosch 0 261 545 040

The Bosch PSS-260 (0 261 545 040) measures absolute pressure from 0 to 260 bar for gasoline direct injection, and also suits diesel, oil or brake fluid. Output is 10-90 % of a 5 V supply, 15.38 mV per bar plus 500 mV. It threads M10x1 with a sealed cone and uses a 3-pole Bosch Compact connector.2

Key specifications

Measures: Absolute fluid pressure (0-260 bar). Output: Analog 0-5 V (ratiometric).

Range
  • 0-260 bar absolute
  • 320 bar maximum
Sourced2
Sensitivity / offset
  • 15.38 mV/bar
  • 500 mV at 5 V
Sourced2
Tolerance
  • 1 % FS0-100 °C
  • 1.5 %-40-0 °C and 100-130 °C
Sourced2
Torque
  • 22 ± 2 N·m in aluminium
  • 32.5 ± 2.5 N·m in steel
Sourced2
AdapterF02U.002.711-01optionalSourced2
Part numberMakerNote
0 261 545 040Bosch2

Pinout and connector

123Schematic, pin-number order (positions not published)
Schematic in pin-number order: the maker does not publish cavity positions. Mating face labels. Pin functions from the maker's document. Our drawing from the published pin list, not a maker drawing.
  • Supply
  • Ground / return
  • Signal
  • Shield
  • Not used / not listed
Download pinout (SVG)
PinFunction (as published)Typical ECU inputWire note
1GroundSensor groundReturn to sensor ground, not chassis
2SignalAnalog voltage input (pull-up off)—
3Supply (5 V)+5 V sensor reference—

Pin functions as published.2 The ECU-input and wire columns are our general guidance, not the maker's.

Connector: Bosch Compact 3-pole; mating part D261.205.366-012 Connector library

Terminals and seals: Not listed: the Bosch data sheet gives the mating housing only, not contact or seal part numbers.

Transfer function and calibration data

Pressure transfer at 5 V2

Ua = 0.5 V + 15.38 mV/bar × p (at Us = 5 V)

0.51.52.4993.4994.499065130195260Absolute pressure (bar)Output (V)

Points computed from Bosch's sensitivity and offset.

Show the 5 data points
Absolute pressure (bar)Output (V)
00.5
651.5
1302.499
1953.499
2604.499

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Transfer function

  • 0.5–4.5 V → 0–26,000 kPa absolute (maker: Ua = 0.5 V + 15.38 mV/bar × p (at Us = 5 V))2Calculated from the maker's data

Worked conversion

  • At 2.5 V the maker's transfer line gives 13,007 kPa absolute (1,886 psia).2Calculated from the maker's data
Pressure transfer at 5 V: output voltage to pressure (16 rows)Calculated from the maker's data
Output (V)Pressure (kPa absolute)Pressure (psia)
0.500
0.751625235.69
13250471.37
1.254875707.06
1.56500942.75
1.758126.61178.67
29753.31414.59
2.2511379.91650.51
2.513006.51886.43
2.7514631.52122.12
316256.52357.81
3.2517881.52593.49
3.519506.52829.18
3.7521131.53064.87
422756.53300.55
4.2524381.53536.24

Interpolated between the maker's published points; nominal values with no tolerance band.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedRail pressure stays on the host ECU's own analog inputs (DI concept); the DI rail-pressure input is still an open item.Medium7
Haltech (Elite / Nexus)Configurable (generic input)Analog voltage input (AVI). Haltech's wiring diagram says inputs are user definable in software; enter the maker's transfer function.89
Link (G4X)Configurable (generic input)Analogue voltage input (9 on the G4X FuryX). Link's public page does not describe how a custom calibration is entered.Medium10
MoTeC (M1)Configurable (generic input)Analogue voltage input (17 on the M150). MoTeC's sensor pages show a manual-calibration option in M1 Tune.Medium1112
ECUMaster (EMU Black)Configurable (generic input)One of 9 analog 0-5 V inputs. ECUMaster lists user-defined sensor characteristics for some functions.Medium13
AEM (Infinity)Configurable (generic input)Analog 0-5 V input (12-bit). AEM's spec sheet does not say how a custom calibration is entered.Medium14
MaxxECUConfigurable (generic input)Extra 0-5 V input (6 on the RACE). The public page does not describe calibration entry.Medium15
Holley (Terminator X / EFI)Configurable (generic input)'5' analog input, set up as a custom sensor in Holley's software (per the wiring manual).16

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Torque depends on the port material; never work on a pressurised DI rail.Medium21

Failure modes and checks

Reading offset

Likely cause Wrong slope or offset in the ECU

Check Use 15.38 mV/bar and 500 mV.Medium2

Seep at the port

Likely cause Wrong torque for the port material

Check Re-torque to 22 N·m (aluminium) or 32.5 N·m (steel) with a new cone.Medium2

Test it with a multimeter

  • Key on, engine off, port open to air: back-probe signal to sensor ground and expect about 0.52 V; the supply pin should read the ECU's 5 V reference.2Calculated from the maker's data

Frequently asked

What thread does the Bosch PSS-260 use?

M10x1 with a sealed cone, 27 mm across flats.2

What does the PSS-260 read at 200 bar?

About 3.58 V at 5 V supply: 0.5 V + 200 × 15.38 mV.2

Related

Use it with GAINS

Bosch PSS-260 DI rail pressure sensor (260 bar) on GAINS hardware

ECU2AVI (0-5 V, pull-up off)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Any free analog input with its pull-up off; 5 V from pin 28, ground to pin 29.Medium3

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

16 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Pressure Sensor Fluid PSS-260 data sheet 411837451 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  5. PSS 260 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  6. internal GAINS internal: DI concept (hardware/mini-di/CONCEPT.md)
  7. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  8. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-10-27
  9. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  10. TMAP Sensor product page · MoTeC · vendor-doc · retrieved 2026-10-27
  11. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  12. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  13. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  14. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.