Bosch · Analog 0-5 V (ratiometric)

Bosch PSS-600 fluid pressure sensor, 0-600 bar (0 261 B23 789-07)

Bosch 0 261 B23 789-07

The Bosch PSS-600 (0 261 B23 789-07) is an absolute fluid pressure sensor for 0-600 bar (0-8,702 psi), aimed at high-pressure gasoline direct-injection rails and also rated for Diesel, oil and brake fluid. It takes 5 V and outputs ratiometric 0.5-4.5 V at 6.67 mV per bar. Pins: 1 ground, 2 signal, 3 supply; M10x1 sealed-cone thread.2

Key specifications

Measures: Absolute fluid pressure, 0-600 bar (0-8,702 psi). Output: Analog 0-5 V (ratiometric).

Range
  • 0-600 bar absolute0-8,702 psi
  • 660 bar maximum9,572 psi
Sourced2
Output10-90 % of supply (0.5-4.5 V at 5 V), ratiometricSourced2
Sensitivity / offset
  • 6.67 mV/bar
  • 500 mV at 5 V
Sourced2
Tolerance
  • ± 1 % FS0-100 °C
  • ± 1.5 % FS-40 to 0 °C and 100-130 °C
Sourced2
Supply4.75-5.25V, 12 mA16 V maxSourced2
Response time2msSourced2
Thread / torque
  • M10x1, 27 mm hex, sealed cone
  • 22 ± 2 N·m in aluminium, 32.5 ± 2.5 N·m in steel
Sourced2
Media

Gasoline (direct injection), Diesel, engine oil, transmission oil, brake fluid

Sourced2
AdapterF02U.002.711-01Bosch accessorySourced2
Temperature-40 to 130 °C operating and media (140 °C peak)Sourced2
Part numberMakerNote
0 261 B23 789-07BoschPrinted 0261.B23.789-07 on the data sheet2

Pinout and connector

123Schematic, pin-number order (positions not published)
Schematic in pin-number order: the maker does not publish cavity positions. Mating face labels. Pin functions from the maker's document. Our drawing from the published pin list, not a maker drawing.
  • Supply
  • Ground / return
  • Signal
  • Shield
  • Not used / not listed
Download pinout (SVG)
PinFunction (as published)Typical ECU inputWire note
1GroundSensor groundReturn to sensor ground, not chassis
2SignalAnalog voltage input (pull-up off)—
3Supply (5 V)+5 V sensor reference—

Pin functions as Bosch publishes them. Note the order differs from the Bosch PS-A air sensors (pin 1 supply there).2 The ECU-input and wire columns are our general guidance, not the maker's.

Connector: Bosch Compact, 3-pole; mating part D261.205.366-012 Connector library

Terminals and seals: Not listed: the data sheet gives the mating housing only.

Transfer function and calibration data

Pressure transfer at 5 V2

Ua = 0.5 V + 0.00667 V/bar × p (at Us = 5 V)

0.51.52.5013.5024.5020150300450600Absolute pressure (bar)Output (V)

Points computed from Bosch's sensitivity and offset.

Show the 5 data points
Absolute pressure (bar)Output (V)
00.5
1501.5
3002.501
4503.502
6004.502

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Transfer function

  • 0.5–4.5 V → 0–60,000 kPa absolute (maker: Ua = 0.5 V + 0.00667 V/bar × p (at Us = 5 V))2Calculated from the maker's data

Worked conversion

  • At 2.5 V the maker's transfer line gives 29,985 kPa absolute (4,349 psia).2Calculated from the maker's data
Pressure transfer at 5 V: output voltage to pressure (9 rows)Calculated from the maker's data
Output (V)Pressure (kPa absolute)Pressure (psia)
0.500
175001087.78
1.5150002175.57
222492.53262.26
2.5299854348.96
337477.55435.66
3.5449706522.35
4524707610.13
4.5599708697.91

Interpolated between the maker's published points; nominal values with no tolerance band.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Any AVI (AVI1-6; pins 17-20, 14 and 26 on the ECU2): 0-5 V input with the pull-up off. Concept hardware.Medium3
Haltech (Elite / Nexus)Configurable (generic input)One of the 11 0-5 V analog inputs listed for the Nexus R3 (switchable 5 V pull-up, set off); enter the maker's transfer function.Medium5
Link (G4X)Configurable (generic input)Analogue voltage input (9 on the G4X FuryX). Link's public page does not describe how a custom calibration is entered.Medium6
MoTeC (M1)Configurable (generic input)Analogue voltage input (17 on the M150). The public page does not describe calibration entry for this sensor.Medium7
ECUMaster (EMU Black)Configurable (generic input)One of 9 analog 0-5 V inputs (10-bit) on the EMU Black. The page lists user-defined characteristics only for fuel pressure.Medium8
AEM (Infinity)Configurable (generic input)Analog 0-5 V input (12-bit). AEM's spec sheet does not say how a custom calibration is entered.Medium9
MaxxECUConfigurable (generic input)Extra 0-5 V input on the RACE. The public page does not describe calibration entry.Medium10
Holley (Terminator X / EFI)UnverifiedNot checked: we cite only public product pages, and none for Holley covers this sensor.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Pin 1 ground, pin 2 signal, pin 3 5 V supply: three wires to an analog input with no pull-up. Bosch states protection against overvoltage, reverse polarity and short circuit.2

Fuel at these pressures is a fire and injection-injury hazard. Depressurise the system first, use the sealed-cone seat at the specified torque and leak-check before running. Bosch advises against mounting the sensor directly on the engine block because of vibration.Medium21

Failure modes and checks

Reads about 0.5 V with the pump running

Likely cause Sensor not seeing pressure: blocked port or a closed valve

Check Check the port and line; 0.5 V is Bosch's zero-pressure output.Medium2

Signal reads near 5 V or 0 V constantly

Likely cause Pins 1 and 3 swapped (this sensor puts ground on pin 1, supply on pin 3)

Check Measure the harness at the connector before plugging in.2

Noisy reading at high rpm

Likely cause Mounted on the block, exposed to vibration beyond its rating

Check Move it to a bracket or line mount as Bosch recommends.Medium2

Test it with a multimeter

  • Key on, engine off, port open to air: back-probe signal to sensor ground and expect about 0.51 V; the supply pin should read the ECU's 5 V reference.2Calculated from the maker's data

Frequently asked

What is the pinout of the Bosch PSS-600?

Pin 1 ground, pin 2 signal, pin 3 5 V supply, on a 3-pole Bosch Compact connector (mating housing D261.205.366-01).2

Why choose a 600 bar sensor over a 260 bar one?

Range. Rail pressures above 260 bar need a wider sensor, and the PSS-600 covers up to 600 bar with a 660 bar limit. The cost is resolution: 6.67 mV per bar against a smaller sensor's steeper slope.Medium2

What does the PSS-600 read at zero pressure?

0.5 V with a 5 V supply. Output rises 6.67 mV per bar to 4.5 V at 600 bar, ratiometric to the supply.2

Related

Use it with GAINS

Bosch PSS-600 fluid pressure sensor, 0-600 bar (0 261 B23 789-07) on GAINS hardware

ECU2AVI (0-5 V, pull-up off)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Any free analog input with its pull-up off; 5 V from pin 28, ground to pin 29.Medium3

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

10 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-11-04
  2. Pressure Sensor Fluid PSS-600 data sheet (2026) · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  5. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-11-04
  6. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  7. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-11-04
  8. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  9. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-11-04