High pressure fuel pump (HPFP)

HPFPGDI pumpdirect injection fuel pumpDI high-pressure pumpcam-driven fuel pumpcommon rail pump

A high pressure fuel pump (HPFP) is an engine-driven piston pump that raises fuel from the low-pressure supply to the pressure a direct-injection rail needs. On gasoline engines that is up to 350 bar (5,076 psi); diesel common rail pumps reach 2,000 bar and more. The ECU meters its output to hold a rail pressure target.346

How it works

The high pressure fuel pump on a gasoline DI engine is usually a single-piston pump driven by an extra lobe on a camshaft.

A follower or bucket rides the lobe and strokes the plunger. Bosch's HDP family is typical: single-cylinder, demand-controlled, and rated to 250 bar (HDP 5.25) or 350 bar (HDP 6.35).384

The pump does not make pressure on its own; it pushes a fixed swept volume per stroke into a closed rail. An inlet metering valve, often called the volume control valve, decides how much of each stroke is trapped and delivered. Fuel not needed spills back to the low-pressure side before the plunger compresses it.Medium31

Because the drive is mechanical, maximum delivery scales with engine speed. Bosch quotes delivery of up to 1.2 to 1.3 cm³ per revolution for its HDP 5 and HDP 6 pumps. That fixed displacement, not the injectors, is often the first fueling limit on a modified DI engine.Medium36

The HPFP depends on its feed. Bosch's GDI system supplies the pump from the in-tank pump at up to 6 bar (87 psi). Low inlet pressure lets fuel vapor form in the pump chamber, so delivery falls even if the pump is healthy.Medium41

Diesel common rail pumps work on the same principle at far higher pressure. Wikipedia describes modern systems above 2,000 bar (29,000 psi), with third-generation piezo systems up to 2,500 bar (36,000 psi). These pumps are fuel-lubricated, so fuel quality and supply pressure directly affect their life.68

Typical values

Gasoline DI rail pressure (max)250 bar or 350 bar, by pump generation3,626 psi · 5,076 psiSourced3
Typical GDI injection pressure (older)About 200 bar2,900 psiLimited by gasoline's poor lubricity on earlier systemsSourced · medium5
Diesel common rail pressure
  • Above 2,000 bar29,000 psi
  • Up to 2,500 bar36,000 psi
Sourced · medium6
Feed pressure to GDI pumpUp to 6 bar from the in-tank pump87 psiSourced4
Delivery per revolution (Bosch HDP)Up to 1.2 cm³ (HDP 5.25) or 1.3 cm³ (HDP 6.35)Sourced3
Rail pressure sensor exampleBosch PSS-260: 0-260 bar absolute, 0.5-4.5 V ratiometricSourced9

How an ECU uses it

The ECU closes the loop on rail pressure.

It sets a target from load and speed, reads the rail pressure sensor, and drives the volume control valve with a timed solenoid pulse synchronized to the pump cam. A feed-forward term from fuel demand plus a PI correction is the usual structure.Medium491

Rail pressure also feeds the injector calculation. Injector flow rises with the square root of pressure difference, so the ECU uses measured rail pressure, not the target, when it computes pulse width. A sensor error therefore shows up as a fueling error as well as a pump-control error.Medium12

When actual pressure stays below target, ECUs set a low-pressure fault such as P0087 under SAE J2012 code definitions and often enter limp mode. Many fall back to a reduced-power mode on low-pressure feed alone; port-and-direct systems may lean on the port injectors instead.Medium104

How to test it

6 checks, in order.

  1. Read codes and freeze-frame data first. Note whether the fault is low pressure, high pressure or sensor plausibility, and at what speed and load it set.Medium10
  2. Check the feed. Fit a gauge or read the low-pressure sensor at the HPFP inlet and confirm the OEM supply specification at idle and at high load. A weak lift pump or clogged filter mimics a failed HPFP.Medium41
  3. Log rail pressure target, actual pressure and volume control valve command with a scan tool during a full-load run. Actual pressure that sags at high rpm while the valve command is at its limit points to a pump at its delivery limit.Medium49
  4. Check the rail pressure sensor at key-on, engine off. It should read close to feed pressure; a reading far off before the engine runs is a sensor or wiring fault, not a pump fault.Medium9
  5. Inspect the cam follower or bucket for wear when the pump is removed. A worn follower shortens the plunger stroke and can damage the cam lobe; replace it per OEM interval.Low1
  6. Safety
    Relieve rail pressure by the OEM procedure before loosening any high-pressure fitting, and fit new single-use lines and seals. Never feel for a leak by hand; fuel at these pressures can penetrate skin.74

Symptoms and causes

Low rail pressure code and limp mode under load

Likely causes Pump at its delivery limit, weak feed pressure, worn follower or failing volume control valve

Check Log feed pressure and rail actual versus target; low feed points upstream, good feed with low rail points to the HPFP

Medium104

Long crank or stall after hot restart

Likely causes Vapor in the pump from low feed pressure, or a leaking pump outlet check valve

Check Watch rail pressure at key-on and how fast it decays after shutdown

Low41

Lean misfires at high rpm only

Likely causes Delivery falls short as fuel demand outgrows pump displacement

Check Compare commanded and actual rail pressure at the misfire point

Medium3

Fuel smell or oil level rising

Likely causes Internal pump seal leak into the crankcase or an external fitting leak

Check Inspect fittings and check oil for fuel dilution

Low1

In tuning

Raising boost or switching to E85 raises fuel mass per cycle, and the HPFP has a hard volume limit.

Log rail pressure versus target before touching fuel tables. If actual pressure drops, larger injectors will not help; the pump or the target must change.34

Upgraded pumps typically use a larger plunger, a different lobe or both, and need matching volume control valve calibration. The pump-control tables in the ECU must suit the new swept volume or pressure control will overshoot or hunt.Medium31

Rail pressure target trades injection time against pump load. A higher target shortens injection time and improves atomization but costs pump capacity, so tuners often trade a little pressure for headroom at peak flow.Medium52

Formula and worked example

Q_max = V_rev × n_pump × η_v
Q_max
maximum fuel volume deliveredcm³/min
V_rev
delivery per pump revolutioncm³
n_pump
pump drive speed (camshaft speed for a cam-driven pump)rpm
η_v
volumetric efficiency of the pump, below 1
Medium31

Try it

hp
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

g/cc
%
psi
psi

Result

Pump flow required228 L/h
At pump outlet pressure53.5 psi
Engine consumption (no margin)183 L/h

Planning estimate from the formula below, not a measurement.

Open the full fuel pump size calculator →

Common mistakes

Mistake Fitting larger DI injectors to fix low rail pressure.

Do instead Larger injectors draw more fuel per event and pull rail pressure down further. Fix pump delivery or feed first, then size injectors.Medium34

Mistake Ignoring the low-pressure feed when the HPFP looks weak.

Do instead Log or gauge HPFP inlet pressure at full load. Starved feed causes cavitation and looks exactly like a worn pump.Medium41

Mistake Reusing high-pressure lines and seals after removal.

Do instead Many OEMs specify new lines or seals after loosening. Follow the torque and replacement rules and leak-check before driving.Low41

Safety, legal and emissions

High-pressure fuel can cause injection injuries and fire.

A pinhole leak at hundreds of bar sprays a fine, flammable mist that can penetrate skin; treat any such injury as a medical emergency.74

Changing fuel-system parts on a road vehicle can affect its emissions certification. The US Clean Air Act prohibits tampering with emissions controls on vehicles used on public roads, and EPA enforces it. This is general information, not legal advice; check the rules where you drive.11

Myths vs facts

Myth A high pressure fuel pump is just a stronger in-tank pump.

Fact It is a separate, engine-driven piston pump fed by the in-tank pump. The in-tank pump supplies a few bar; the HPFP multiplies that to hundreds of bar.48

Myth More rail pressure always means more power.

Fact Pressure improves atomization but does not add fuel by itself. Above what the pump can hold, a higher target only causes pressure faults and limp mode.Medium35

Myth The HPFP sets rail pressure with a spring regulator.

Fact Modern GDI pumps are demand-controlled: the ECU meters each stroke through a solenoid valve against a pressure sensor. A relief valve only protects against overpressure.Medium39

Frequently asked

What does a high pressure fuel pump do?

It takes fuel from the in-tank pump at a few bar and raises it to direct-injection rail pressure, up to 350 bar on current gasoline engines. The ECU meters how much each stroke delivers so rail pressure follows a target that changes with load and speed.43

What are the symptoms of a bad high pressure fuel pump?

Common signs are a low rail pressure code, reduced-power mode under load, hard hot starts, and lean misfires at high rpm. The same signs come from a weak lift pump or a bad sensor, so log feed pressure and rail actual versus target before replacing the pump.Medium104

Can you drive with a bad HPFP?

Usually only in limp mode. Most ECUs cut power when rail pressure falls well below target to avoid lean running. Driving on a failing pump risks lean misfires and engine damage under load, so diagnose it before using full throttle again.Medium101

What pressure does a direct injection fuel pump run?

Gasoline DI pumps from Bosch are rated to 250 bar (3,626 psi) or 350 bar (5,076 psi) depending on generation, while older systems often ran near 200 bar. Diesel common rail pumps exceed 2,000 bar (29,000 psi). Actual pressure varies with load.356

When do you need an HPFP upgrade?

When logs show rail pressure falling below target at high load with healthy feed pressure. That means fuel demand exceeds the pump's swept volume, common after big boost increases or an ethanol blend. Upgraded pumps need matching ECU pump-control calibration.Medium34

Wiring, pinouts and parts

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

11 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  3. High-pressure pump for gasoline direct injection · Bosch Mobility · vendor-doc · retrieved 2026-10-27
  4. Gasoline direct injection system overview · Bosch Mobility · vendor-doc · retrieved 2026-10-27
  5. Gasoline direct injection · Wikipedia · reference · retrieved 2026-10-27
  6. Common rail · Wikipedia · reference · retrieved 2026-10-27
  7. Injection pump · Wikipedia · reference · retrieved 2026-10-27
  8. Fuel pump · Wikipedia · reference · retrieved 2026-10-27
  9. Pressure Sensor Fluid PSS-260 data sheet 411837451 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  10. SAE J2012: Diagnostic Trouble Code Definitions · SAE International · standard · retrieved 2026-10-27
  11. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (2020) · U.S. Environmental Protection Agency · standard · retrieved 2026-10-27