Lift pump

low-pressure fuel pumptransfer pumpfeed pumpsupply pumpLPFP

A lift pump is the low-pressure pump that moves fuel from the tank to a high-pressure pump, injection pump or surge tank. On gasoline direct injection it supplies up to about 6 bar (87 psi); on diesels it keeps the injection pump flooded with bubble-free fuel. It sets feed pressure, not injection pressure.Medium36

How it works

A lift pump exists because high-pressure pumps are poor at pulling fuel.

They are piston pumps designed to compress a full chamber, and suction at their inlet lets vapor or air form. The lift pump pushes fuel to them so every stroke starts with liquid.Medium63

On gasoline DI the lift pump is usually the in-tank electric pump. Bosch's GDI system feeds the HPFP at up to 6 bar (87 psi). Many systems vary its speed, raising feed pressure under high load and hot fuel to resist vapor.Medium310

On diesels the lift pump may be in the tank, on the frame rail, or built into the injection pump. Diesel injection pumps are lubricated by the fuel itself, so any air, vapor or starvation reduces lubrication as well as flow.Medium65

In a surge-tank fuel system, the lift pump moves fuel from the main tank into the surge tank. It only has to replace what the engine burns, since return fuel flows back into the surge tank rather than the main tank.Low71

Typical values

Gasoline DI feed pressureUp to 6 bar87 psiSourced3
Port-injection in-tank pumpAbout 40-60 psi3-4 barHere the in-tank pump is the main pump, not a lift pumpSourced · medium6
Carbureted mechanical pumpAbout 10-15 psi0.7-1.0 barSourced · medium6
Diesel common rail downstreamAbove 2,000 bar at the rail29,000 psiSourced · medium4
Diesel injection pump inlet
  • Per OEM specification
  • Varies by pump
Check the service manual figureLow confidence5

How an ECU uses it

Many modern systems close a loop on feed pressure.

A low-pressure sensor on the supply line reports to the ECU or a pump control module, which varies lift pump duty to hold a target that rises with fuel demand and fuel temperature.Medium1098

If feed pressure falls below a threshold, ECUs typically log a fault and may limit power, because the high-pressure pump can no longer be trusted to hold rail pressure.Low113

How to test it

5 checks, in order.

  1. Find the OEM feed pressure specification and the test point, usually the filter outlet or the HPFP inlet, or read the low-pressure sensor PID with a scan tool.Medium1
  2. Measure feed pressure at idle, then at high load while logging. Pressure that drops under load or after the fuel heats up points to a weak lift pump, clogged filter or restricted pickup.Medium310
  3. Run a volume test into a fuel-safe container for a timed period with the pump powered directly, and compare with the maker's flow at that voltage.Low61
  4. Check supply voltage at the pump connector while it runs. A drop of more than about 0.5 V from battery points to wiring, relay or ground losses, not the pump.Low1
  5. On diesels, fit a clear section of line before the injection pump temporarily to look for air bubbles, which indicate a suction leak.Low5

Symptoms and causes

Low rail pressure code with a good HPFP

Likely causes Low feed pressure from a weak lift pump, clogged filter or wiring loss

Check Measure feed pressure and pump voltage under load

Medium311

Hard hot restart

Likely causes Vapor at the high-pressure pump inlet from low feed pressure

Check Log feed pressure during hot soak and restart

Low3

Diesel stalls or loses power going uphill

Likely causes Air in the supply, failing lift pump or restricted pickup

Check Check for bubbles in a clear line and measure inlet pressure

Low5

Pump whine that changes with fuel level

Likely causes Worn pump or pickup uncovering at low fuel

Check Repeat the pressure test at full and low tank level

Low7

In tuning

Fuel upgrades start at the tank.

A bigger HPFP or injectors on a stock lift pump often fail because feed pressure drops at peak demand. Log feed pressure on every full-load pull after any fuel change.Medium32

Ethanol blends need more fuel volume, around a third more for E85, so lift pump capacity must rise with them. Size it with margin for low battery voltage and pump wear.Medium1310

Try it

hp
:1

Typical: gasoline NA 0.45-0.50, gasoline boosted 0.55-0.65, E85 NA 0.65-0.75, E85 boosted 0.80-0.90 lb/hp-hr.

g/cc
%
psi
psi

Result

Pump flow required228 L/h
At pump outlet pressure53.5 psi
Engine consumption (no margin)183 L/h

Planning estimate from the formula below, not a measurement.

Open the full fuel pump size calculator →

Common mistakes

Mistake Upgrading the high-pressure pump but keeping a stock lift pump.

Do instead Size the lift pump for the new peak flow and verify feed pressure under load.Medium32

Mistake Measuring feed pressure only at idle.

Do instead Low pressure usually appears at high flow and hot fuel. Test under load and after a heat soak.Medium310

Mistake Undersized wiring to a higher-flow pump.

Do instead Run a relay-fed circuit with wire and fuse sized for pump current, and check voltage at the pump.Low1

Safety, legal and emissions

Lift pumps move flammable fuel and draw high current near the tank.

Fuse the circuit for pump draw, keep a crash or stall shutoff path, and leak-check fittings before running.Medium16

Changing fuel-system parts on a road vehicle can affect its emissions certification. The US Clean Air Act prohibits tampering with emissions controls on vehicles used on public roads, and EPA enforces it. This is general information, not legal advice; check the rules where you drive.12

Myths vs facts

Myth The lift pump only matters for starting.

Fact It sets the inlet pressure for the high-pressure pump at every operating point. Low feed under load causes vapor, poor delivery and, on diesels, reduced lubrication of the injection pump.Medium63

Myth A diesel with an engine-driven pump does not need a lift pump.

Fact Some injection pumps include an internal transfer pump, but long or high-lift supply runs and high flow still benefit from a dedicated pump. Follow the OEM layout for the specific pump.Low51

Frequently asked

What does a lift pump do?

A lift pump moves fuel from the tank to the high-pressure or injection pump and keeps that pump's inlet full of liquid fuel at a set feed pressure. It prevents vapor and air at the inlet, which would cut delivery and, on diesels, lubrication.Medium63

What are the symptoms of a bad lift pump?

Typical signs are low rail pressure codes, power loss under load, hard hot starts and, on diesels, stalling or surging. Confirm with a feed pressure test under load, and check pump voltage and the filter before replacing the pump.Medium311

How do you test a lift pump?

Put a gauge on the feed line at the filter outlet or high-pressure pump inlet, or log the low-pressure sensor. Check pressure at idle and full load against the OEM figure, then run a timed volume test and check voltage at the pump connector.Medium13

What pressure should a lift pump make?

It depends on the system. Bosch's gasoline DI feed runs up to 6 bar (87 psi), while carbureted mechanical pumps make about 10 to 15 psi. Diesel feed pressures are pump-specific, so use the service manual value for the injection pump fitted.Medium36

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

13 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. High-pressure pump for gasoline direct injection · Bosch Mobility · vendor-doc · retrieved 2026-10-27
  3. Gasoline direct injection system overview · Bosch Mobility · vendor-doc · retrieved 2026-10-27
  4. Common rail · Wikipedia · reference · retrieved 2026-10-27
  5. Injection pump · Wikipedia · reference · retrieved 2026-10-27
  6. Fuel pump · Wikipedia · reference · retrieved 2026-10-27
  7. Fuel tank · Wikipedia · reference · retrieved 2026-10-27
  8. Pressure Sensor Fluid PSS-10 data sheet 69547659 · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  9. US 6,532,941: Electronic returnless fuel system · Google Patents · reference · retrieved 2026-10-27
  10. US 7,774,125: Programmable fuel pump control · US Patent and Trademark Office · reference · retrieved 2026-10-27
  11. SAE J2012: Diagnostic Trouble Code Definitions · SAE International · standard · retrieved 2026-10-27
  12. Tampering Policy: The EPA's Enforcement Policy on Vehicle and Engine Tampering and Aftermarket Defeat Devices (2020) · U.S. Environmental Protection Agency · standard · retrieved 2026-10-27
  13. Flexible fuel vehicles · US Department of Energy, Alternative Fuels Data Center · reference · retrieved 2026-10-27