Bosch · NTC thermistor

Bosch NTC M12-H temperature sensor (to 150 °C)

Bosch 0 281 002 170

The Bosch NTC M12-H (0 281 002 170) is an M12x1.5 fluid temperature thermistor rated -40 to 150 °C, which suits engine oil. It shares the NTC M12's table to 130 °C (2.5 kΩ at 20 °C), extends to 57 Ω at 150 °C, and quotes ± 0.8 °C accuracy at 100 °C. It uses a 2-pin Bosch Compact connector.2

Key specifications

Measures: Temperature of oil, coolant or fuel. Output: NTC thermistor.

Range-40 to 150°CSourced2
Nominal resistance2.5 kΩ ± 6 % at 20 °CSourced2
Accuracy
  • ± 1.4 °C at 25 °C
  • ± 0.8 °C at 100 °C
Sourced2
Thread / torqueM12x1.5, 19 mm, 18 N·m, aluminium washerSourced2
Part numberMakerNote
0 281 002 170Bosch2

Pinout and connector

12Schematic, pin-number order (positions not published)
Schematic in pin-number order: the maker does not publish cavity positions. Mating face labels. Pin functions from the maker's document. Our drawing from the published pin list, not a maker drawing.
  • Supply
  • Ground / return
  • Signal
  • Shield
  • Not used / not listed
Download pinout (SVG)
PinFunction (as published)Typical ECU inputWire note
1SIG+Temperature input (pull-up on)—
2SIG−Sensor groundReturn to sensor ground, not chassis

Pin functions as published.2 The ECU-input and wire columns are our general guidance, not the maker's.

Connector: Bosch Compact 2-pin; mating part 2-pole Compact D261.205.337-0125 Connector library

Terminals and seals: Not listed: the Bosch data sheet gives the mating housing only, not contact or seal part numbers.

Transfer function and calibration data

Resistance vs temperature2
1001,00010,000-407.555102.5150Temperature (°C)Resistance (Ω), log scale
Show the 20 data points
Temperature (°C)Resistance (Ω)
-4045,313
-3026,114
-2015,462
-109,397
05,896
103,792
202,500
301,707
401,175
50834
60596
70436
80323
90243
100187
110144
120113
13089
14071
15057

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Transfer function

  • NTC: 45,313 Ω at -40 °C falling to 57 Ω at 150 °C2
  • Steinhart-Hart fit through -40 °C, 60 °C, 150 °C: A = 1.3117e-3, B = 2.5715e-4, C = 1.7878e-7 (largest error against the maker's table 0.42 °C).2Calculated from the maker's data

Worked conversion

  • At 20 °C the element is 2,500 Ω; with a 1 kΩ pull-up to 5 V the ECU sees 5 × 2,500 / (2,500 + 1,000) = 3.571 V.2Calculated from the maker's data
Resistance vs temperature: resistance and ECU input voltage (20 rows)Calculated from the maker's data
Temperature (°C)Resistance (Ω)V at 1 kΩ pull-up to 5 VV at 2.2 kΩ pull-up to 5 V
-40453134.8924.768
-30261144.8164.611
-20154624.6964.377
-1093974.5194.051
058964.2753.641
1037923.9573.164
2025003.5712.66
3017073.1532.185
4011752.7011.741
508342.2741.374
605961.8671.066
704361.5180.827
803231.2210.64
902430.9770.497
1001870.7880.392
1101440.6290.307
1201130.5080.244
130890.4090.194
140710.3310.156
150570.270.126

Resistance from the maker's table. The maker does not state a pull-up; 1 kΩ and 2.2 kΩ are example values: use your ECU's actual pull-up.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)AVI with the switchable pull-up on (AVI5, pin 14, is the default coolant input). Concept hardware.Medium3
Haltech (Elite / Nexus)Configurable (generic input)AVI with its software-selectable 1 kΩ pull-up to 5 V switched on; enter the maker's resistance table.Medium7
Link (G4X)Configurable (generic input)Temperature input with the selectable pull-up switched on (4 on the FuryX). Pull-up value not stated for G4X.8
MoTeC (M1)Configurable (generic input)Analogue temperature input (1 kΩ pull-up to sensor 5 V per the M150 pinout).9
ECUMaster (EMU Black)Configurable (generic input)Temperature sensor input (IAT, CLT and oil temperature are listed). Pull-up value not stated publicly.Medium10
AEM (Infinity)Configurable (generic input)Analog temperature input (2.49 kΩ pull-up to 5 V per the Series 5 spec).11
MaxxECUConfigurable (generic input)Temperature input (2 extra on the RACE). Pull-up value not on the public pages.Medium12
Holley (Terminator X / EFI)Configurable (generic input)Thermistor 'T' input for two-wire temperature sensors. Pull-up value not stated.13

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Pin 1 to an analog input with the pull-up on (Bosch suggests 1 or 3 kΩ), pin 2 to sensor ground.2

Failure modes and checks

Oil temperature never above 130 °C on track

Likely cause Using a 130 °C-rated sensor or table

Check Fit the M12-H and extend the ECU table to 150 °C.Medium21

Reading cold

Likely cause Open circuit

Check Measure resistance at the plug.Medium2

Test it with a multimeter

  • Unplugged, measure resistance across the two element pins: about 2,500 Ω at 20 °C, falling as it warms (compare with the table).2Calculated from the maker's data

Frequently asked

What temperature range does the Bosch NTC M12-H cover?

-40 to 150 °C, 20 °C more than the standard NTC M12, with the same resistance curve below 130 °C.21

Which pin is signal on the NTC M12-H?

Bosch labels pin 1 SIG+ and pin 2 SIG−. A thermistor is not polarised, but keep pin 2 on sensor ground for consistency.Medium2

Related

Use it with GAINS

Bosch NTC M12-H temperature sensor (to 150 °C) on GAINS hardware

ECU2AVI (thermistor, pull-up on)

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

Any free analog input with its pull-up switched on.Medium3

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

13 sources
  1. Temperature Sensor NTC M12 data sheet 70101387 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  2. Temperature Sensor NTC M12-H data sheet 70115595 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  5. NTC M12 H product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  6. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  7. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  8. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  9. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  10. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  11. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.