Bosch · NTC thermistor
Bosch NTC M12 temperature sensor
The Bosch NTC M12 (0 280 130 026) is a fluid temperature thermistor for coolant, oil or fuel from -40 to 130 °C. It reads 2.5 kΩ ± 5 % at 20 °C and 187 Ω at 100 °C, threads in M12x1.5 at 25 N·m and uses a 2-pole Jetronic connector. Bosch suggests a 1 or 3 kΩ pull-up at the ECU.1
Key specifications
Measures: Temperature of coolant, oil or fuel. Output: NTC thermistor.
| Part number | Maker | Note |
|---|---|---|
| 0 280 130 026 | Bosch | 1 |
Pinout and connector
- Supply
- Ground / return
- Signal
- Shield
- Not used / not listed
| Pin | Function (as published) | Typical ECU input | Wire note |
|---|---|---|---|
| 1 | SIG+ | Temperature input (pull-up on) | — |
| 2 | SIG− | Sensor ground | Return to sensor ground, not chassis |
Element pins; the NTC has no polarity.1 The ECU-input and wire columns are our general guidance, not the maker's.
Connector: Bosch Jetronic 2-pole; mating part D261.205.288-011 Connector library
Terminals and seals: Not listed: the Bosch data sheet gives the mating housing only, not contact or seal part numbers.
Transfer function and calibration data
Show the 18 data points
| Temperature (°C) | Resistance (Ω) |
|---|---|
| -40 | 45,313 |
| -30 | 26,114 |
| -20 | 15,462 |
| -10 | 9,397 |
| 0 | 5,896 |
| 10 | 3,792 |
| 20 | 2,500 |
| 30 | 1,707 |
| 40 | 1,175 |
| 50 | 834 |
| 60 | 596 |
| 70 | 436 |
| 80 | 323 |
| 90 | 243 |
| 100 | 187 |
| 110 | 144 |
| 120 | 113 |
| 130 | 89 |
How it's calibrated
ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.
Transfer function
- NTC: 45,313 Ω at -40 °C falling to 89 Ω at 130 °C1
- Steinhart-Hart fit through -40 °C, 50 °C, 130 °C: A = 1.3095e-3, B = 2.5726e-4, C = 1.7969e-7 (largest error against the maker's table 0.25 °C).1Calculated from the maker's data
Worked conversion
- At 20 °C the element is 2,500 Ω; with a 1 kΩ pull-up to 5 V the ECU sees 5 × 2,500 / (2,500 + 1,000) = 3.571 V.11Calculated from the maker's data
Resistance vs temperature: resistance and ECU input voltage (18 rows)Calculated from the maker's data
| Temperature (°C) | Resistance (Ω) | V at 1 kΩ pull-up to 5 V | V at 3 kΩ pull-up to 5 V |
|---|---|---|---|
| -40 | 45313 | 4.892 | 4.69 |
| -30 | 26114 | 4.816 | 4.485 |
| -20 | 15462 | 4.696 | 4.188 |
| -10 | 9397 | 4.519 | 3.79 |
| 0 | 5896 | 4.275 | 3.314 |
| 10 | 3792 | 3.957 | 2.792 |
| 20 | 2500 | 3.571 | 2.273 |
| 30 | 1707 | 3.153 | 1.813 |
| 40 | 1175 | 2.701 | 1.407 |
| 50 | 834 | 2.274 | 1.088 |
| 60 | 596 | 1.867 | 0.829 |
| 70 | 436 | 1.518 | 0.634 |
| 80 | 323 | 1.221 | 0.486 |
| 90 | 243 | 0.977 | 0.375 |
| 100 | 187 | 0.788 | 0.293 |
| 110 | 144 | 0.629 | 0.229 |
| 120 | 113 | 0.508 | 0.181 |
| 130 | 89 | 0.409 | 0.144 |
Resistance from the maker's table; voltages calculated for the maker-recommended pull-ups.
Native support across ECUs
| ECU platform | Status | How to set it up | Source |
|---|---|---|---|
| GAINS ECU2Concept | Configurable (generic input) | AVI with the switchable pull-up on (AVI5, pin 14, is the default coolant input). Concept hardware. | Medium2 |
| Haltech (Elite / Nexus) | Configurable (generic input) | AVI with its software-selectable 1 kΩ pull-up to 5 V switched on; enter the maker's resistance table. | Medium6 |
| Link (G4X) | Configurable (generic input) | Temperature input with the selectable pull-up switched on (4 on the FuryX). Pull-up value not stated for G4X. | 7 |
| MoTeC (M1) | Preset listed | MoTeC's sensor page says to use the predefined M1 calibration for Bosch 0 280 130 026 (status only; its table is not reproduced here). | 8 |
| ECUMaster (EMU Black) | Configurable (generic input) | Temperature sensor input (IAT, CLT and oil temperature are listed). Pull-up value not stated publicly. | Medium9 |
| AEM (Infinity) | Configurable (generic input) | Analog temperature input (2.49 kΩ pull-up to 5 V per the Series 5 spec). | 10 |
| MaxxECU | Configurable (generic input) | Temperature input (2 extra on the RACE). Pull-up value not on the public pages. | Medium11 |
| Holley (Terminator X / EFI) | Configurable (generic input) | Thermistor 'T' input for two-wire temperature sensors. Pull-up value not stated. | 12 |
Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.
Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.
CAD and drawings
- Data sheetTemperature Sensor NTC M12 data sheet 70101387 (PDF)1Download from Bosch MotorsportNo login at last check; the maker may change this
- DrawingOffer drawing45Download from Bosch MotorsportNo login at last check; the maker may change this
- 3D CAD3D data (zip)45Download from Bosch MotorsportNo login at last check; the maker may change this
We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.
Wiring and installation
Two wires, non-polarised: one to an analog input with the pull-up on, one to sensor ground. Any mounting orientation is allowed.1
Failure modes and checks
Likely cause Open circuit or corroded Jetronic contacts
Check Measure resistance at the plug against the table.Medium1
Likely cause No sealing washer (not included)
Check Fit a suitable sealing washer or thread sealant for the port.Medium1
Test it with a multimeter
- Unplugged, measure resistance across the two element pins: about 2,500 Ω at 20 °C, falling as it warms (compare with the table).1Calculated from the maker's data
Frequently asked
What is the resistance of the Bosch 0 280 130 026?
2,500 Ω at 20 °C, 5,896 Ω at 0 °C and 187 Ω at 100 °C, per Bosch's table.1
What pull-up resistor suits the Bosch NTC M12?
Bosch suggests 1 or 3 kΩ. Enter the same value in the ECU or the thermistor calculator so the voltage converts to the right temperature.1
Related
Use it with GAINS
Bosch NTC M12 temperature sensor on GAINS hardware
GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.23
Concept Pre-release hardware. Pin assignments come from the current design documents and may change.
Sources
12 sources
- Temperature Sensor NTC M12 data sheet 70101387 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
- internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
- internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
- NTC M12 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
- Bosch Motorsport legal notice · Bosch Motorsport (Robert Bosch GmbH) · vendor-doc · retrieved 2026-10-27
- Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
- G4X FuryX product page · Link Engine Management · vendor-doc · retrieved 2026-10-27
- Water Temperature Sensor product page (#55001) · MoTeC · vendor-doc · retrieved 2026-10-27
- EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
- Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
- MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
- HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27
Not yet indexed: fewer than 3 FAQs.

