GM · Frequency / pulse width

GM 15865791 mass airflow sensor with IAT (LS3 / LS7)

GM 15865791GM 12576410ACDelco 213-4222

GM 15865791 (replacing 12576410, ACDelco 213-4222) is a GM mass airflow sensor with a built-in intake air temperature sensor. GM's catalog lists it on the 2006-13 Corvette and 2010-15 Camaro 6.2 and 7.0 V8s, plus many four- and six-cylinder Chevrolets, which makes it a common LS3 and LS7 swap MAF. GM does not publish its pinout or transfer function.Medium45

Key specifications

Measures: Intake air mass flow, plus intake air temperature. Output: Frequency / pulse width.

Built-in IATYesGM: mass airflow sensor with intake air temperature sensorSourced · medium4
V8 applications
  • 2006-13 Corvette 6.2 L and 7.0 L
  • 2010-15 Camaro SS 6.2 L and 7.0 L
Sourced · medium45
Other applications (catalog)

2005-10 Cobalt, 2006-11 HHR, 2007-12 Colorado, 2008-14 Malibu, 2010-11 Equinox and others

Sourced · medium4
Mounting parts
  • GM 19166574 aluminium weld flange
  • GM 15813321 seal
Low confidence5
Output typeUnverifiedGM does not publish it publicly. GM MAFs of this era are widely reported as frequency output; confirm with a scope or frequency meter before choosing the ECU input.Researched, unverified
PinoutUnverifiedNot in a public GM document we could archive; use GM service wiring for the donor vehicle.Researched, unverified
Airflow transfer tableUnverifiedNot published by GM; calibrate on the vehicle against lambda and fuel trims.Researched, unverified
Part numberMakerNote
15865791GMMedium45
12576410GMEarlier number; GM's catalog lists 15865791 as replacing itMedium4
213-4222ACDelcoACDelco service number given by the retailerLow5

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedINJ5-6 (4-cylinder builds) or IGN5-6 as a digital/frequency input with the 2.2 kΩ pull-up; a MAF airflow model is not in the concept yet.Medium6
Haltech (Elite / Nexus)Configurable (generic input)One of the 6 synchronised pulsed inputs, which Haltech lists as usable as frequency inputs. The product page does not mention MAF calibration.Medium8
Link (G4X)UnverifiedThe public FuryX page does not mention MAF or frequency-input airflow sensors.No public source
MoTeC (M1)UnverifiedThe public M150 page does not mention MAF sensors.No public source
ECUMaster (EMU Black)UnverifiedThe EMU Black page does not mention MAF or frequency inputs.No public source
AEM (Infinity)UnverifiedNot confirmed from the Series 5 spec sheet for a frequency MAF.No public source
MaxxECUUnverifiedThe RACE page does not list MAF or frequency inputs.No public source
Holley (Terminator X / EFI)UnverifiedNot checked: we cite only public product pages, and none for Holley covers this sensor.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Use the donor vehicle's GM wiring diagram for pin functions. The airflow output goes to a frequency-capable digital input, the IAT to an analog input with its pull-up on, and supply and ground follow GM's circuit.Medium14

Keep the factory housing, flange and a straight run of pipe ahead of the sensor. Turbulence or a different bore changes what the element sees and moves the calibration.Medium21

Failure modes and checks

Lean or rich trims after an intake change

Likely cause A different housing, screen or inlet bend shifts the calibration

Check Bosch notes a MAF element is calibrated to its housing as one unit; keep the factory housing or recalibrate the airflow table.Medium24

Airflow reads high and trims go lean after a filter service

Likely cause Oil film on the element from an oiled-gauze filter

Check Inspect the element; GM has issued a bulletin on oiled filters contaminating MAF sensors.Low3

No airflow reading

Likely cause No supply or a broken element

Check Check supply and ground at the connector with the key on, then the signal with the engine running.Medium1

Frequently asked

What engines use the GM 15865791 MAF?

GM's catalog lists the 2006-13 Corvette and 2010-15 Camaro 6.2 L and 7.0 L V8s, which is why it is called the LS3/LS7 MAF, plus several four- and six-cylinder Chevrolets such as the Cobalt, HHR and Malibu.Medium45

Does the GM 15865791 have an IAT sensor?

Yes. GM names it a mass airflow sensor with intake air temperature sensor, so one connector carries both the airflow and IAT signals.Medium4

What replaced GM 12576410?

GM's catalog lists 15865791 as the replacement for 12576410. The ACDelco service number is 213-4222.Medium45

Can I run an LS3 swap without the MAF?

Yes, if the ECU runs speed-density from a MAP sensor. A MAF is optional for a standalone ECU; keep it only if the ECU's airflow model uses it.Medium1

Related

Use it with GAINS

GM 15865791 mass airflow sensor with IAT (LS3 / LS7) on GAINS hardware

ECU2Digital/frequency input personality

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

MAF airflow (frequency): INJ5-6 on 4-cylinder builds or IGN5-6, pull-up on. An airflow model is not in the concept firmware yet.Medium6

ECU2AVI (thermistor, pull-up on)

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

Any free analog input with its pull-up switched on.Medium6

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.67

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-11-04
  2. Air Mass Meters: overview, features and benefits (Aug 2017) · Robert Bosch Ltd (Bosch Automotive Aftermarket UK) · vendor-doc · retrieved 2026-11-04
  3. Mass flow sensor (Wikipedia) · Wikipedia · reference · retrieved 2026-11-04
  4. Chevrolet 15865791 sensor (mass airflow with intake air temperature) catalog listing · gmpartsgiant.com (GM dealer parts catalog) · oem · retrieved 2026-11-04
  5. GM 15865791 LS3 LS7 MAF mass air flow sensor 213-4222 (product page) · michiganmotorsports.com · vendor-doc · retrieved 2026-11-04
  6. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  7. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  8. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-11-04

Not yet indexed: more than 40% of specs unverified.