GM · Frequency / pulse width

GM 15904068 / 19330121 mass airflow sensor with IAT (2001-07 trucks, LS V8)

GM 19330121GM 15904068GM 25318411GM 25168491

GM 15904068 and 25318411 are earlier numbers for the truck mass airflow sensor GM now lists as 19330121, with a built-in intake air temperature sensor. GM's catalog fits it to 2001-07 Silverado and Sierra, Tahoe, Yukon, Avalanche, Escalade and Hummer H2 V8s from 4.8 to 8.1 L. A dealer site also lists 25168491 as replaced. GM does not publish its pinout.Medium45

Key specifications

Measures: Intake air mass flow, plus intake air temperature. Output: Frequency / pulse width.

Built-in IAT

Yes (GM: sensor asm, mass airflow, w/ intake air temperature sensor)

Sourced · medium4
Applications (catalog)
  • 2001-07 Silverado / Sierra 4.3-8.1 L
  • 2001-06 Tahoe, Yukon, Suburban
  • 2002-06 Avalanche, Escalade
  • 2003-07 Hummer H2 6.0 L
  • 2005-06 GTO 6.0 L
  • 2004-05 Bonneville GXP 4.6 L
Sourced · medium4
Output typeUnverifiedGM does not publish it publicly. GM MAFs of this era are widely reported as frequency output; confirm with a scope or frequency meter before choosing the ECU input.Researched, unverified
PinoutUnverifiedNot in a public GM document we could archive; use GM service wiring for the donor vehicle.Researched, unverified
Airflow transfer tableUnverifiedNot published by GM; calibrate on the vehicle against lambda and fuel trims.Researched, unverified
Part numberMakerNote
19330121GMCurrent GM number (some dealer sites mark it no longer available)Medium4
15904068GMReplaced by 19330121 per GM's catalogMedium4
25318411GMReplaced by 19330121 per GM's catalogMedium4
25168491GMListed as replaced by 19330121 on a GM dealer site (search excerpt only)Low5

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptTo be confirmedINJ5-6 (4-cylinder builds) or IGN5-6 as a digital/frequency input with the 2.2 kΩ pull-up; a MAF airflow model is not in the concept yet.Medium6
Haltech (Elite / Nexus)Configurable (generic input)One of the 6 synchronised pulsed inputs, which Haltech lists as usable as frequency inputs. The product page does not mention MAF calibration.Medium8
Link (G4X)UnverifiedThe public FuryX page does not mention MAF or frequency-input airflow sensors.No public source
MoTeC (M1)UnverifiedThe public M150 page does not mention MAF sensors.No public source
ECUMaster (EMU Black)UnverifiedThe EMU Black page does not mention MAF or frequency inputs.No public source
AEM (Infinity)UnverifiedNot confirmed from the Series 5 spec sheet for a frequency MAF.No public source
MaxxECUUnverifiedThe RACE page does not list MAF or frequency inputs.No public source
Holley (Terminator X / EFI)UnverifiedNot checked: we cite only public product pages, and none for Holley covers this sensor.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Engines that use it

From the platform catalog's sensor table; check fitment against your engine code and model year.

Wiring and installation

Use the donor truck's GM wiring diagram for pin functions. Route the airflow signal to a frequency-capable digital input and the IAT to an analog input with its pull-up on.Medium14

Keep the truck's MAF housing and a straight inlet ahead of the sensor; a different bore or a sharp bend upstream shifts the airflow calibration.Medium21

Failure modes and checks

Lean or rich trims after an intake change

Likely cause A different housing, screen or inlet bend shifts the calibration

Check Bosch notes a MAF element is calibrated to its housing as one unit; keep the factory housing or recalibrate the airflow table.Medium24

Airflow reads high and trims go lean after a filter service

Likely cause Oil film on the element from an oiled-gauze filter

Check Inspect the element; GM has issued a bulletin on oiled filters contaminating MAF sensors.Low3

No airflow reading

Likely cause No supply or a broken element

Check Check supply and ground at the connector with the key on, then the signal with the engine running.Medium1

Frequently asked

What replaced GM 15904068?

GM's catalog lists 19330121 as replacing both 15904068 and 25318411. Some dealer sites now mark 19330121 as no longer available, so check stock before ordering.Medium45

Is GM 25168491 the same MAF as 15904068?

A GM dealer site lists 25168491 among the numbers replaced by 19330121, alongside 15904068 and 25318411. We saw that only as a search excerpt, so treat it as likely but confirm against your VIN.Low5

What trucks use the GM 19330121 MAF?

GM's catalog lists 2001-07 Silverado and Sierra (4.3 L to 8.1 L), 2001-06 Tahoe, Yukon and Suburban, 2002-06 Avalanche and Escalade, the 2003-07 Hummer H2 and the 2005-06 GTO.Medium4

Do I need the MAF for a 5.3 swap on a standalone ECU?

No, not if the ECU runs speed-density from a MAP sensor. The MAF's built-in IAT can still serve as the air temperature input if you keep it in the intake.Medium1

Related

Use it with GAINS

GM 15904068 / 19330121 mass airflow sensor with IAT (2001-07 trucks, LS V8) on GAINS hardware

ECU2Digital/frequency input personality

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

MAF airflow (frequency): INJ5-6 on 4-cylinder builds or IGN5-6, pull-up on. An airflow model is not in the concept firmware yet.Medium6

ECU2AVI (thermistor, pull-up on)

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

Any free analog input with its pull-up switched on.Medium6

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.67

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-11-04
  2. Air Mass Meters: overview, features and benefits (Aug 2017) · Robert Bosch Ltd (Bosch Automotive Aftermarket UK) · vendor-doc · retrieved 2026-11-04
  3. Mass flow sensor (Wikipedia) · Wikipedia · reference · retrieved 2026-11-04
  4. GM 19330121 sensor asm, mass airflow (w/ intake air temperature sensor) catalog listing · gmpartsgiant.com (GM dealer parts catalog) · oem · retrieved 2026-11-04
  5. GM 19330121 mass airflow sensor with intake air temperature sensor (dealer listing, seen as search excerpt) · worldpartsdirect.com (GM dealer parts site) · oem · retrieved 2026-11-04
  6. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  7. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  8. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-11-04

Not yet indexed: more than 40% of specs unverified.