GM · NTC thermistor

GM 25036751 intake air temperature sensor (3/8 NPT, brass)

GM 25036751GM 25037225

GM 25036751 is a threaded intake air (manifold air, or air charge) temperature sensor with a 3/8 in NPT brass body. It replaced 25037225 and was fitted to many 1980s-90s GM cars and trucks, and it is a common choice for adding an IAT to an intake pipe or manifold on swaps. It is a two-wire NTC thermistor; GM does not publish its resistance table publicly.Medium23

Key specifications

Measures: Intake air temperature. Output: NTC thermistor.

Thread3/8 in NPT, brass bodySourced · medium3
GM names
  • Air intake temperature sensor
  • Intake manifold temperature sensor
  • Air charge temperature sensor
Sourced · medium2
Factory applications (examples)
  • 1985-95 Corvette
  • 1985-92 Firebird
  • 1987-93 S10 pickup
  • 1991 Syclone
  • 1993 Typhoon
  • 1985-88 Fiero
  • Many Buick, Cadillac and Oldsmobile models
Sourced · medium32
Connector
  • Two-pin GM sensor connector
  • The retailer says it matches common LS IAT breakout harnesses
Low confidence3
Resistance tableUnverifiedNot in a public GM document we could archive; measure it or use GM service data.Researched, unverified
Element exposure and response timeUnverifiedNot published by GM in a document we could archive.Researched, unverified
Part numberMakerNote
25036751GMMedium23
25037225GMEarlier number; GM's catalog lists 25036751 as replacing itMedium2

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)AVI with the switchable pull-up on (pins 14, 17-20 or 26 on the ECU2). Concept hardware.Medium4
Haltech (Elite / Nexus)Configurable (generic input)0-5 V analog input with the switchable 5 V pull-up on; enter the sensor's resistance table.Medium6
Link (G4X)Configurable (generic input)Temperature input with the selectable pull-up switched on (4 on the FuryX). Pull-up value not stated for G4X.Medium7
MoTeC (M1)Configurable (generic input)Analogue temperature input on the M150; enter the sensor's resistance table.Medium8
ECUMaster (EMU Black)Configurable (generic input)Temperature sensor input (IAT and CLT are listed). Pull-up value not stated publicly.Medium9
AEM (Infinity)Configurable (generic input)Analog temperature input (2.49 kΩ pull-up to 5 V per the Series 5 spec).Medium10
MaxxECUConfigurable (generic input)IAT input, or one of the 2 extra temperature inputs on the RACE. Pull-up value not on the public page.Medium11
Holley (Terminator X / EFI)UnverifiedNot checked: we cite only public product pages, and none for Holley covers this sensor.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Two wires: one to sensor ground, the other to an analog input with its pull-up switched on. A thermistor has no polarity, so either pin works. Without a published GM table, log resistance against a reference thermometer at several temperatures and build the curve.Medium1

Mount it where it sees moving charge air: after the intercooler on boosted engines and away from hot metal, so heat soak from the manifold does not bias the reading.Medium1

Failure modes and checks

IAT climbs at idle and falls when driving

Likely cause Heat soak: the sensor body is warmed by the manifold or a hot pipe

Check Move it to the inlet pipe, or compare against a thermocouple in the same airflow.Medium1

Reads -40 °C (open) or very hot (short)

Likely cause Broken wire, missing pull-up or shorted connector

Check Measure resistance at the sensor, then check the ECU input has its pull-up on.Medium1

Frequently asked

What is GM 25036751?

A GM intake air temperature sensor with a 3/8 in NPT brass body, also listed by GM as an intake manifold or air charge temperature sensor. It replaced 25037225 in GM's catalog.Medium23

What thread is the GM 25036751 IAT sensor?

3/8 in NPT, so it screws into a tapped bung in an intake pipe or manifold. Use a sealant suited to the thread and avoid over-tightening the tapered thread in aluminium.Medium3

What is the resistance table of the GM 25036751?

GM does not publish it in a public document we could archive. Measure resistance against a reference thermometer at several temperatures, or use GM service data, and enter that table rather than copying one from another sensor.Medium21

What vehicles used the GM 25036751?

GM's catalog and retailers list many 1984-95 GM cars and light trucks, including the Corvette, Firebird, S10, Syclone, Typhoon and Fiero. Confirm against your VIN, since GM fitted several temperature sensors in that era.Medium23

Related

Use it with GAINS

GM 25036751 intake air temperature sensor (3/8 NPT, brass) on GAINS hardware

ECU2AVI (thermistor, pull-up on)

Pins
On the ECU2 pin map
Pull-up
On
Shielding
Not needed

Any free analog input with its pull-up switched on.Medium4

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.45

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

11 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-11-04
  2. GM 25036751 Air Intake Temperature Sensor catalog listing · gmpartsgiant.com (GM dealer parts catalog) · oem · retrieved 2026-11-04
  3. GM 25036751 intake air temperature sensor with 3/8 NPT thread (product page) · michiganmotorsports.com · vendor-doc · retrieved 2026-11-04
  4. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  5. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  6. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-11-04
  7. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  8. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-11-04
  9. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  10. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-11-04