Sensor type · Potentiometer 0-5 V · Hall effect (digital)

Throttle position sensor

TPSthrottle potentiometerthrottle angle sensor

A throttle position sensor (TPS) reports throttle-blade angle as a 0-5 V signal on three wires: 5 V reference, sensor ground and signal. Cable throttles use one track. Drive-by-wire throttle bodies carry two redundant tracks, and on the Bosch Motorsport electronic throttle body one rises from 0 to 5 V while the other falls from 5 to 0 V over 0-90°.12

Parts in the library

Support across ECUs

Across the 10 parts in this hub (2 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU210 configurable (generic input)
Haltech (Elite / Nexus)1 configurable (generic input) · 9 unverified
Link (G4X)1 configurable (generic input) · 9 unverified
MoTeC (M1)1 configurable (generic input) · 9 unverified
ECUMaster (EMU Black)1 configurable (generic input) · 9 unverified
AEM (Infinity)1 configurable (generic input) · 9 unverified
MaxxECU1 configurable (generic input) · 9 unverified
Holley (Terminator X / EFI)1 configurable (generic input) · 9 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

Most throttle sensors are a resistive track or a contactless Hall element on the throttle shaft. The ECU feeds 5 V and ground and reads the wiper or Hall output as a fraction of the supply, so the reading is ratiometric.2

On an electronic throttle body two sensors measure the same angle in opposite directions. The ECU compares them continuously, which is how it detects a failed track and drops to a safe idle position.12

A standalone ECU learns the closed and wide-open voltages of the actual sensor during setup. The numbers between those end points become 0-100 % throttle.Medium2

Types and variants

Single-track (cable throttle)Potentiometer 0-5 V

One wiper on a resistive track: 5 V, ground, signal. Used with mechanical throttles.2

Dual-track (drive-by-wire)Potentiometer 0-5 V

Two redundant outputs with opposite slopes, 0-5 V and 5-0 V for 0-90° on the Bosch electronic throttle body; supply 5 ± 0.2 V for the sensors.1

Contactless Hall TPSHall effect (digital)

A magnet on the shaft and a Hall element; no wiper to wear. Output is still a 0-5 V analog level.Medium2

Wiring

Wire the TPS reference and ground to the ECU's own sensor 5 V and sensor ground, never to chassis ground, so the ratiometric reading cancels supply drift.Medium2

Electronic throttle sensors are safety-relevant: both tracks must reach the ECU that drives the throttle motor directly, never through a CAN gateway or another module.Medium13

Connector and wiring library

Common faults and checks

Hesitation or a spike at one pedal position

Likely cause Worn spot on a resistive track

Check Sweep the throttle slowly while logging TPS; a worn track shows a step or dropout at the same angle every time.Medium2

TPS stuck at 0 % or 100 %

Likely cause Open reference or open ground (stuck low or high)

Check Back-probe 5 V and ground at the sensor connector with the key on; both should match the ECU's sensor rail.Medium2

Drive-by-wire fault, limp idle

Likely cause The two tracks disagree beyond the ECU's plausibility limit

Check Log both tracks; on the Bosch ETB their sum should stay near the 5 V supply across the sweep.Medium1

Frequently asked

How do you wire a 3-wire TPS?

One pin is the 5 V reference, one is sensor ground and one is the signal. Feed the reference and ground from the ECU's sensor rail, not from chassis ground, and take the signal to an analog input. Identify the pins by measuring: resistance between reference and ground stays constant, while the signal pin changes as the throttle moves.Medium2

Why does a drive-by-wire throttle have two position signals?

For redundancy. Two sensors read the same angle, often with opposite slopes, so the ECU can spot a failed track by comparing them. Bosch's motorsport throttle body outputs 0-5 V on one track and 5-0 V on the other over 0-90°.1

What voltage should a TPS read?

It depends on the sensor, which is why a standalone ECU learns the actual closed and wide-open voltages during calibration. A healthy sensor never sits at exactly 0 V or 5 V, so readings at the rails usually mean an open or shorted circuit.Medium2

Related

Use it with GAINS

Throttle position sensor on GAINS hardware

ECU2AVI1-AVI2 (drive-by-wire TPS1/TPS2)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Throttle tracks for drive-by-wire. DBW sensors are allowed only on AVI1-6, never on a flex pin or over CAN. 5 V on pin 28, ground on pin 29.Medium3

ECU2AVI (cable throttle)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

With a cable throttle, any AVI input reads a single-track TPS (the K20 cable example uses AVI1).Medium3

Analog inputs AVI1-6 take 0-5 V sensors, thermistors or switches, each with a switchable pull-up. Sensor 5 V is pin 28 (250 mA shared) and sensor ground is pin 29.3

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.34

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Electronic Throttle Body data sheet 68749835 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  2. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  3. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  4. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

Not yet indexed: fewer than 4 FAQs.