Bosch · Potentiometer 0-5 V

Bosch 0 280 750 156 electronic throttle body (68 mm)

Bosch 0 280 750 156

Bosch 0 280 750 156 is a 68 mm electronic throttle body that Bosch Motorsport Australia sells with mating connector D 261 205 358-01. Bosch's pin-layout sheet lists a 68 mm body weighing 1.1 kg (2.4 lb) with a 75 mm flange, the motor on pins 1 and 4 and the sensor tracks on pins 5 and 6.Medium42

Key specifications

Measures: Throttle plate angle (two redundant tracks); motor-driven throttle actuator. Output: Potentiometer 0-5 V.

Bore68mm2.68 inSourced42
Flange diameter75mm2.95 inBosch's pin-layout sheet gives this for its 68 mm body without an order number.Sourced · medium2
Hole pattern65 × 65mmBosch lists this as hole diameter.Sourced · medium2
Weight1.1kg2.4 lbSourced · medium2
Opening directionCounterclockwiseview A on the Bosch drawingSourced · medium2
RedundancyDual potentiometer tracksSourced4
Sensor supply and output slopesUnverifiedBosch Motorsport's data sheet does not list a 68 mm body; its electrical data is likely shared but not stated for this number.Researched, unverified
Part numberMakerNote
0 280 750 156Bosch68 mm bore, sold by Bosch Motorsport Australia4

Pinout and connector

Unverified, confirm before wiring

123456Schematic, pin-number order (positions not published)
Schematic in pin-number order: the maker does not publish cavity positions. Mating face labels. Unverified: confirm before wiring. Our drawing from the published pin list, not a maker drawing.
  • Supply
  • Ground / return
  • Signal
  • Shield
  • Not used / not listed
Download pinout (SVG)
PinFunction (as published)Typical ECU inputWire note
1Motor − (A)Analog voltage input (pull-up off)—
2Sensor ground, Poti − (B)Sensor groundReturn to sensor ground, not chassis
3Sensor supply 5 V, Poti + (C)+5 V sensor reference—
4Motor + (D)Analog voltage input (pull-up off)—
5Sensor signal 2, Poti 2 (E)Analog voltage input (pull-up off)—
6Sensor signal 1, Poti 1 (F)Analog voltage input (pull-up off)—

Bosch's pin-layout sheet gives this order for its 68 mm body but lists no order number; Bosch Motorsport Australia sells 0 280 750 156 as its 68 mm body. Confirm before wiring.Medium24 The ECU-input and wire columns are our general guidance, not the maker's.

Connector: Bosch 6-pin (AMP) throttle body connector; mating part D 261 205 358-0142 Connector library

Terminals and seals: Sold with the mating housing by Bosch Motorsport; terminal numbers not listed on the pages cited.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Throttle tracks on AVI1/AVI2 (pins 17-18) with the pull-up off; motor on the H-bridge pins 21-22 of the ECU2. Concept hardware: the drive-by-wire path needs qualified-human review before release.Medium5
Haltech (Elite / Nexus)UnverifiedNot checked against a public Haltech document that names this throttle body. Confirm drive-by-wire support and the setup with Haltech before wiring.No public source
Link (G4X)UnverifiedNot checked against a public Link document that names this throttle body. Confirm drive-by-wire support and the setup with Link before wiring.No public source
MoTeC (M1)UnverifiedNot checked against a public MoTeC document that names this throttle body. Confirm drive-by-wire support and the setup with MoTeC before wiring.No public source
ECUMaster (EMU Black)UnverifiedNot checked against a public ECUMaster document that names this throttle body. Confirm drive-by-wire support and the setup with ECUMaster before wiring.No public source
AEM (Infinity)UnverifiedNot checked against a public AEM document that names this throttle body. Confirm drive-by-wire support and the setup with AEM before wiring.No public source
MaxxECUUnverifiedNot checked against a public MaxxECU document that names this throttle body. Confirm drive-by-wire support and the setup with MaxxECU before wiring.No public source
Holley (Terminator X / EFI)UnverifiedNot checked against a public Holley document that names this throttle body. Confirm drive-by-wire support and the setup with Holley before wiring.No public source

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Wire motor pins 1 and 4 to the ECU's H-bridge and the three sensor pins to its sensor 5 V, sensor ground and two analog inputs. Bosch states the body connects directly to ECUs with electronic throttle control.21

Bosch Motorsport Australia states this body needs an electronic accelerator pedal and an ECU able to run electronic throttle control.4

Failure modes and checks

Limp idle with a throttle fault

Likely cause Track disagreement or an open sensor ground

Check Log both tracks through a slow sweep; they should move in opposite directions without steps.Medium41

Throttle drives closed against the stop at key-on

Likely cause Motor pins 1 and 4 reversed

Check Confirm motor + is pin 4 and motor − is pin 1 per Bosch's pin layout before powering the H-bridge.Medium2

Frequently asked

What is the pinout of Bosch 0 280 750 156?

Bosch's pin-layout sheet for its 68 mm body gives pin 1 motor −, 2 sensor ground, 3 sensor 5 V, 4 motor +, 5 signal 2 and 6 signal 1. The sheet has no order numbers, so confirm on the part.Medium2

What connector does the Bosch 68 mm throttle body use?

Bosch Motorsport Australia lists mating connector D 261 205 358-01, the same as the 32, 40, 54, 60 and 82 mm bodies.42

How heavy is the Bosch 68 mm throttle body?

1.1 kg (2.4 lb), per Bosch's pin-layout sheet.Medium2

Related

Use it with GAINS

Bosch 0 280 750 156 electronic throttle body (68 mm) on GAINS hardware

ECU2AVI1-AVI2 (TPS1/TPS2) + HB1/HB2 (motor)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Throttle tracks on AVI1/AVI2, motor on the H-bridge pins 21-22 (about 3 A continuous / 10 A peak, under review). DBW sensors never over CAN.Medium5

Drive-by-wire control is safety-relevant; the ECU2's DBW path needs qualified-human review before release.5

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.56

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Electronic Throttle Body data sheet 68749835 (51017995, 27 Jan 2026) · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
  2. Electronic Throttle Body Variations: pin layouts PDF 147514891 · Bosch Motorsport · vendor-doc · retrieved 2026-11-04
  3. ELECTRONIC THROTTLE BODY product page (downloads) · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  4. Electronic Throttle Body (68mm bore) 0 280 750 156 · Bosch Motorsport Australia (Robert Bosch Australia) · vendor-doc · retrieved 2026-11-04
  5. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  6. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)