Bosch · Potentiometer 0-5 V
Bosch 0 280 750 473 electronic throttle body (82 mm)
Bosch 0 280 750 473 is an 82 mm electronic throttle body, the largest bore Bosch Motorsport lists. Bosch Motorsport Australia sells it with a grooved inlet flange and mating connector D 261 205 358-01; Bosch's data sheet gives 0 280 750 101 for its 82 mm body. Retailers cross it to Porsche 997 605 116 01.Medium415
Key specifications
Measures: Throttle plate angle (two redundant tracks); motor-driven throttle actuator. Output: Potentiometer 0-5 V.
- 6-16 V
- Generator current < 10 A
| I | 0-5 V for 0-90° |
|---|---|
| II | 5-0 V for 0-90° |
Pinout and connector
Unverified, confirm before wiring
- Supply
- Ground / return
- Signal
- Shield
- Not used / not listed
| Pin | Function (as published) | Typical ECU input | Wire note |
|---|---|---|---|
| 1 | Motor − (A) | Analog voltage input (pull-up off) | — |
| 2 | Sensor ground, Poti − (B) | Sensor ground | Return to sensor ground, not chassis |
| 3 | Sensor supply 5 V, Poti + (C) | +5 V sensor reference | — |
| 4 | Motor + (D) | Analog voltage input (pull-up off) | — |
| 5 | Sensor signal 2, Poti 2 (E) | Analog voltage input (pull-up off) | — |
| 6 | Sensor signal 1, Poti 1 (F) | Analog voltage input (pull-up off) | — |
Bosch's pin-layout sheet gives this order for its 82 mm body, which its data sheet numbers 0 280 750 101. Bosch Motorsport Australia sells 0 280 750 473 as its 82 mm body with the same mating connector. Confirm before wiring.Medium24 The ECU-input and wire columns are our general guidance, not the maker's.
Connector: Bosch 6-pin (AMP) throttle body connector; mating part D 261 205 358-0142 Connector library
Terminals and seals: Sold with the mating housing by Bosch Motorsport; terminal numbers not listed on the pages cited.
Transfer function and calibration data
Output I = 5 V × angle / 90°; Output II = 5 V − Output I
From Bosch Motorsport's data sheet for its ETB range (82 mm listed as 0 280 750 101); the ECU learns the actual end stops.
Show the 3 data points
| Throttle angle (°) | Output I (V) |
|---|---|
| 0 | 0 |
| 45 | 2.5 |
| 90 | 5 |
How it's calibrated
ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.
Transfer function
- 0–5 V → 0–90 ° (maker: Output I = 5 V × angle / 90°; Output II = 5 V − Output I)1
Worked conversion
- At 2.5 V the output corresponds to 45 °.1Calculated from the maker's data
Throttle position outputs: output voltage to throttle angle (11 rows)Calculated from the maker's data
| Output (V) | Throttle angle (°) |
|---|---|
| 0 | 0 |
| 0.5 | 9 |
| 1 | 18 |
| 1.5 | 27 |
| 2 | 36 |
| 2.5 | 45 |
| 3 | 54 |
| 3.5 | 63 |
| 4 | 72 |
| 4.5 | 81 |
| 5 | 90 |
Interpolated between the maker's published points; nominal values with no tolerance band.
Native support across ECUs
| ECU platform | Status | How to set it up | Source |
|---|---|---|---|
| GAINS ECU2Concept | Configurable (generic input) | Throttle tracks on AVI1/AVI2 (pins 17-18) with the pull-up off; motor on the H-bridge pins 21-22 of the ECU2. Concept hardware: the drive-by-wire path needs qualified-human review before release. | Medium6 |
| Haltech (Elite / Nexus) | Unverified | Not checked against a public Haltech document that names this throttle body. Confirm drive-by-wire support and the setup with Haltech before wiring. | No public source |
| Link (G4X) | Unverified | Not checked against a public Link document that names this throttle body. Confirm drive-by-wire support and the setup with Link before wiring. | No public source |
| MoTeC (M1) | Unverified | Not checked against a public MoTeC document that names this throttle body. Confirm drive-by-wire support and the setup with MoTeC before wiring. | No public source |
| ECUMaster (EMU Black) | Unverified | Not checked against a public ECUMaster document that names this throttle body. Confirm drive-by-wire support and the setup with ECUMaster before wiring. | No public source |
| AEM (Infinity) | Unverified | Not checked against a public AEM document that names this throttle body. Confirm drive-by-wire support and the setup with AEM before wiring. | No public source |
| MaxxECU | Unverified | Not checked against a public MaxxECU document that names this throttle body. Confirm drive-by-wire support and the setup with MaxxECU before wiring. | No public source |
| Holley (Terminator X / EFI) | Unverified | Not checked against a public Holley document that names this throttle body. Confirm drive-by-wire support and the setup with Holley before wiring. | No public source |
Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.
Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.
CAD and drawings
- Data sheetElectronic Throttle Body data sheet 68749835 (PDF)1Download from Bosch MotorsportNo login at last check; the maker may change this
- Pin layoutElectronic Throttle Body Variations: pin layouts PDF (pin order differs between bore sizes)2Download from Bosch MotorsportNo login at last check; the maker may change this
- 3D CAD3D data and offer drawings (zip)3Download from Bosch MotorsportNo login at last check; the maker may change this
We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.
Wiring and installation
Wire motor pins 1 and 4 to the ECU's H-bridge and the three sensor pins to its sensor 5 V, sensor ground and two analog inputs. Bosch states the body connects directly to ECUs with electronic throttle control.21
Retail cross-reference data lists this number for Porsche 997 and 991 911 and some Cayenne and Panamera V8 models. Treat that list as a lead, and check the Porsche part number on the body.Low5
Failure modes and checks
Likely cause Track disagreement or an open sensor ground
Check Log both tracks; output I plus output II should stay near the 5 V supply through the sweep.Medium1
Likely cause Motor pins 1 and 4 reversed
Check Confirm motor + is pin 4 and motor − is pin 1 per Bosch's pin layout before powering the H-bridge.Medium2
Frequently asked
What size is Bosch 0 280 750 473?
82 mm (3.23 in) bore, per Bosch Motorsport Australia.4
What is the difference between Bosch 0 280 750 473 and 0 280 750 101?
Both are 82 mm Bosch bodies. Bosch Motorsport's data sheet orders its 82 mm body as 0 280 750 101, while Bosch Motorsport Australia sells 0 280 750 473 and notes a groove on the inlet flange. Bosch does not say whether they are otherwise identical.Medium14Sources disagree
What is the pinout of the Bosch 82 mm throttle body?
Bosch's pin-layout sheet for its 82 mm body: pin 1 motor −, 2 sensor ground, 3 sensor 5 V, 4 motor +, 5 signal 2, 6 signal 1. Confirm it matches a 473 before wiring.Medium2
What cars use Bosch 0 280 750 473?
A parts retailer cross-references it to Porsche 997 605 116 01 and lists 911 (997, 991), Cayenne and Panamera V8 applications. Porsche's own catalog was not checked.Low5
Related
Use it with GAINS
Bosch 0 280 750 473 electronic throttle body (82 mm) on GAINS hardware
Drive-by-wire control is safety-relevant; the ECU2's DBW path needs qualified-human review before release.6
GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.67
Concept Pre-release hardware. Pin assignments come from the current design documents and may change.
Sources
- Electronic Throttle Body data sheet 68749835 (51017995, 27 Jan 2026) · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-11-04
- Electronic Throttle Body Variations: pin layouts PDF 147514891 · Bosch Motorsport · vendor-doc · retrieved 2026-11-04
- ELECTRONIC THROTTLE BODY product page (downloads) · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
- Electronic Throttle Body (82mm bore) 0 280 750 473 · Bosch Motorsport Australia (Robert Bosch Australia) · vendor-doc · retrieved 2026-11-04
- Bosch throttle body 0 280 750 473: OE cross-reference and applications · Winparts (parts retailer, TecDoc-style data) · vendor-doc · retrieved 2026-11-04
- internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
- internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

