Bosch · Potentiometer 0-5 V

Bosch electronic throttle body (redundant TPS)

Bosch 0 280 750 148Bosch 0 280 750 149Bosch 0 280 750 150Bosch 0 280 750 151Bosch 0 280 750 101Bosch Motorsport F02U.V01.184-02

Bosch's electronic throttle bodies come in bores from 32 to 82 mm and carry two redundant throttle position sensors: output I runs 0-5 V and output II 5-0 V over 0-90°. The sensors take 5 ± 0.2 V, the motor 6-16 V, and every body has a default idle-air position for limp home.1

Key specifications

Measures: Throttle plate angle (two redundant tracks). Output: Potentiometer 0-5 V.

Bores32, 40, 44, 46, 52, 54, 60, 82 mmSourced1
Sensor supply5± 0.2 VSourced1
Motor supply
  • 6-16 V
  • Generator current < 10 A
Sourced1
Outputs
I0-5 V for 0-90°
II5-0 V for 0-90°
Sourced1
Temperature-40 to 140°CSourced1
Fuels

Flex-fuel, CNG and LPG permissible when injected after the throttle body

Sourced1
Connector pinoutUnverifiedBosch's data sheet does not list pins; reseller pinouts are not used here.Researched, unverified
Part numberMakerNote
0 280 750 148Bosch32 mm1
0 280 750 149Bosch40 mm1
0 280 750 150Bosch54 mm1
0 280 750 151Bosch60 mm1
0 280 750 101Bosch82 mm1
F02U.V01.184-02Bosch Motorsport52 mm1

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector not published. Browse the connector library

Transfer function and calibration data

Throttle position outputsMedium1

Output I = 5 V × angle / 90°; Output II = 5 V − Output I

01.252.53.755022.54567.590Throttle angle (°)Output I (V)

Nominal end points from the data sheet; the ECU learns actual end stops.

Show the 3 data points
Throttle angle (°)Output I (V)
00
452.5
905

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Transfer function

  • 0–5 V → 0–90 ° (maker: Output I = 5 V × angle / 90°; Output II = 5 V − Output I)1

Worked conversion

  • At 2.5 V the output corresponds to 45 °.1Calculated from the maker's data
Throttle position outputs: output voltage to throttle angle (11 rows)Calculated from the maker's data
Output (V)Throttle angle (°)
00
0.59
118
1.527
236
2.545
354
3.563
472
4.581
590

Interpolated between the maker's published points; nominal values with no tolerance band.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Any AVI (AVI1-6; pins 17-20, 14 and 26 on the ECU2): 0-5 V input with the pull-up off. Concept hardware. Electronic throttle control also needs the ECU's drive-by-wire output and its safety checks.Medium2
Haltech (Elite / Nexus)Configurable (generic input)Analog voltage input (AVI). Haltech's wiring diagram says inputs are user definable in software; enter the maker's transfer function. Electronic throttle control also needs the ECU's drive-by-wire output and its safety checks.78
Link (G4X)Configurable (generic input)Analogue voltage input (9 on the G4X FuryX). Link's public page does not describe how a custom calibration is entered. Electronic throttle control also needs the ECU's drive-by-wire output and its safety checks.Medium9
MoTeC (M1)Configurable (generic input)Analogue voltage input (17 on the M150). MoTeC's sensor pages show a manual-calibration option in M1 Tune. Electronic throttle control also needs the ECU's drive-by-wire output and its safety checks.Medium1011
ECUMaster (EMU Black)Configurable (generic input)One of 9 analog 0-5 V inputs. ECUMaster lists user-defined sensor characteristics for some functions. Electronic throttle control also needs the ECU's drive-by-wire output and its safety checks.Medium12
AEM (Infinity)Configurable (generic input)Analog 0-5 V input (12-bit). AEM's spec sheet does not say how a custom calibration is entered. Electronic throttle control also needs the ECU's drive-by-wire output and its safety checks.Medium13
MaxxECUConfigurable (generic input)Extra 0-5 V input (6 on the RACE). The public page does not describe calibration entry. Electronic throttle control also needs the ECU's drive-by-wire output and its safety checks.Medium14
Holley (Terminator X / EFI)Configurable (generic input)'5' analog input, set up as a custom sensor in Holley's software (per the wiring manual). Electronic throttle control also needs the ECU's drive-by-wire output and its safety checks.15

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Both throttle tracks and the motor connect to the ECU that runs electronic throttle control; Bosch states the body connects directly to control units with ETC functionality. Respect the data sheet's mounting position.1

Failure modes and checks

Limp idle with a fault

Likely cause Track disagreement or motor fault

Check Log both tracks; output I plus output II should stay near 5 V.Medium1

Throttle will not close fully

Likely cause Mounting or linkage stress

Check Check the mounting against Bosch's mounting-position notes.Medium1

Frequently asked

What are the TPS signals on a Bosch electronic throttle body?

Two opposing tracks: output I rises 0-5 V and output II falls 5-0 V over 0-90° of throttle, from a 5 ± 0.2 V sensor supply.1

What sizes do Bosch electronic throttle bodies come in?

Bosch's data sheet lists 32, 40, 44, 46, 52, 54, 60 and 82 mm bores.1

Related

Use it with GAINS

Bosch electronic throttle body (redundant TPS) on GAINS hardware

ECU2AVI1-AVI2 (TPS1/TPS2) + HB1/HB2 (motor)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Throttle tracks on AVI1/AVI2, motor on the H-bridge pins 21-22 (about 3 A continuous / 10 A peak, under review). DBW sensors never over CAN.Medium2

Drive-by-wire control is safety-relevant; the ECU2's DBW path needs qualified-human review before release.2

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.23

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

15 sources
  1. Electronic Throttle Body data sheet 68749835 · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  2. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  3. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  4. ELECTRONIC THROTTLE BODY product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  5. Electronic throttle body pin layouts (PDF 147514891) · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  6. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  7. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-10-27
  8. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  9. TMAP Sensor product page · MoTeC · vendor-doc · retrieved 2026-10-27
  10. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  11. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  12. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  13. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.