Throttle position sensor (TPS)

TPSTPS sensorthrottle position sensorthrottle angle sensorthrottle pot

A throttle position sensor (TPS) is a sensor on the throttle shaft that reports throttle opening to the ECU as a voltage. Most are potentiometers or non-contact Hall sensors fed from a regulated 5 V reference. The ECU uses the signal to detect idle and wide-open throttle, add transient fuel, estimate load on alpha-N systems and police drive-by-wire.341

How it works

A potentiometer TPS has a resistive track and a wiper that turns with the throttle shaft.

The track ends connect to the 5 V reference and sensor ground, so the wiper voltage rises in proportion to throttle angle. The sensor is a voltage divider: its output is a fraction of whatever reference it receives.531

The reference is a regulated 5 V rail, not battery voltage, because battery voltage sags while cranking and rises above 14 V while charging. The ECU's converter uses the same 5 V rail as its reference, so a small drift moves signal and reference together and cancels out. This is called ratiometric measurement.Medium19

Non-contact sensors put a magnet on the shaft and a Hall-effect element in the housing. Nothing rubs, so there is no track to wear and no dead spot, and the output is still an analog voltage. Many drive-by-wire throttle bodies and pedals use non-contact sensing for that reason.Medium671

Electronic throttle bodies carry two position tracks. Bosch's motorsport throttle body outputs one signal rising from 0 to 5 V and a second falling from 5 to 0 V over 0 to 90° of plate travel, from a 5 ± 0.2 V sensor supply. Other designs use two rising tracks with different slopes or offsets.41

The ECU reads both position and rate of change. Rate of change triggers acceleration enrichment, because opening the throttle quickly fills the manifold faster than a MAP or MAF signal can show. Position alone flags closed-throttle idle and wide-open conditions.Medium13

Typical values

Sensor supply
  • 5.0 V regulated
  • Bosch ETB specifies 5 ± 0.2 V
Sourced4
Bosch ETB track 10 to 5 V over 0 to 90° of openingSourced4
Bosch ETB track 25 to 0 V over 0 to 90° of openingSourced4
Opposite-slope plausibilityTrack 1 + track 2 ≈ supply voltage at every angleSaab Trionic T7 flags P1230 when the sum leaves 4.59-5.70 V; offset-slope designs use other checksSourced410
End pointsKept off the 0 V and 5 V rails on most sensorsLets the ECU tell a short or open circuit from a real end positionSourced · medium13
Operating temperature (Bosch ETB)-40 to 140°C-40 to 284 °FSourced4

How an ECU uses it

The ECU converts TPS voltage to 0-100% using learned closed and wide-open end points.

A reading at the closed point flags idle, which enables idle speed control and deceleration fuel cut. A reading near the open end flags full load and can select full-load fuel and timing.Medium13

Rate of change drives transient fueling. A fast opening adds fuel before MAP or MAF can register the airflow step, and a fast closing removes fuel to limit rich spikes. On alpha-N strategies, throttle angle and rpm are the main load axes.Medium12

On drive-by-wire, TPS is the feedback for the throttle motor's position loop. The ECU compares both tracks with each other and with the commanded angle. A disagreement beyond the plausibility window, or a plate that cannot follow its target, sets a fault, cuts motor power and lets the springs park the plate in its limp position.47

How to test it

6 checks, in order.

  1. Check the reference first: key on, engine off, back-probe the connector and measure between the 5 V supply and sensor ground. Expect about 5.0 V; Bosch specifies 5 ± 0.2 V for its throttle body. A low or missing reference points to wiring, or to another sensor shorting the shared 5 V rail.41
  2. Measure signal to sensor ground at closed throttle, then open the throttle slowly to wide open. On a cable throttle, move the lever by hand; on drive-by-wire, use the pedal and read live data. The voltage should change smoothly, with no steps, dropouts or jumps.Medium51
  3. Use a scope or a fast ECU log to find dead spots. A worn track shows a brief drop or jump at the same angle on every sweep. A multimeter updates too slowly to catch a short dropout reliably.Medium51
  4. On dual-track sensors, log both tracks together. On opposite-slope designs such as the Bosch throttle body, the two voltages should add up to roughly the supply at every angle. On offset designs, the relationship between tracks should stay constant through the sweep.410
  5. Wiggle the harness and connector while watching live data at a steady throttle angle. A flicker that follows the wiggle points to a connector, loose pin or chafed wire rather than the sensor itself.Medium1
  6. Safety
    with the key on, a drive-by-wire plate can snap open or shut under motor power. Keep fingers out of the bore, and only move the plate by hand with the ignition off or the throttle connector unplugged.Medium74

Symptoms and causes

Stumble or hesitation at the same throttle angle

Likely causes Worn or dirty potentiometer track creating a dead spot; loose connector

Check Log a slow sweep; a dropout at a repeatable angle is the track, a flicker that follows wiggling is wiring.

Medium51

Reduced power, limited throttle and a warning light on drive-by-wire

Likely causes Track disagreement, open supply or ground, or a plate that cannot follow its target

Check Read codes, then log both tracks and commanded versus actual angle; disagreement points to sensor or wiring, a lagging plate to the mechanism.

Medium74

High or hunting idle, no decel fuel cut

Likely causes Closed-throttle reading above the learned zero, misadjusted stop or sticking cable

Check Compare live TPS at rest with the learned closed value; relearn or fix the stop if it sits above 0%.

Medium13

TPS stuck at 0% or 100%

Likely causes Open reference, open ground, or signal shorted to a rail

Check Back-probe 5 V and ground at the plug with the key on; a reading pinned at a rail usually means wiring.

Medium1

Harsh or late automatic shifts

Likely causes Wrong or noisy TPS signal used by the transmission controller

Check Compare TPS with pedal position and engine data on a scan tool; fix the TPS before re-adapting the transmission.

Medium3

Check engine light, wrong idle, cruise control off and throttle in limp-home

Likely causes Two-track plausibility fault: the track voltages no longer agree, from a wiring break, short or a failing sensor

Check Log both track voltages and wiggle the harness while watching them. Saab's P1230 test, for example, uses a 4.59-5.70 V sum window.

10

In tuning

Calibrate the TPS before any other tuning.

Record the voltage at fully closed and fully open throttle so the ECU maps them to 0 and 100%. A closed reading above 0% can disable idle control and deceleration fuel cut, and a wide-open reading below 100% can block full-load tables.Medium31

On alpha-N or blended load strategies, the TPS is the main load input, so resolution near closed throttle matters most. Small throttle angles change airflow a lot, and a noisy or worn track shows up as unstable fueling at light load.Medium12

Acceleration enrichment triggers on TPS rate, so signal noise adds fuel at random. Set the rate threshold above the noise seen in a steady-throttle log and filter lightly, rather than turning enrichment down to hide a noisy sensor.Medium1

Common mistakes

Mistake Calibrating the TPS once and never rechecking it after moving the throttle stop, cable or body.

Do instead Rerun the closed and wide-open learn after any change, and confirm the reading returns to 0% every time the pedal is released.Medium31

Mistake Feeding the TPS from a 12 V switched supply or another device's 5 V rail.

Do instead Power it from the ECU's own 5 V reference and sensor ground so supply drift cancels ratiometrically.Medium19

Mistake Wiring only one track of a drive-by-wire throttle, or swapping the two tracks.

Do instead Wire and calibrate both tracks, then unplug each in turn and confirm the throttle drops to its default before driving.Medium47

Mistake Turning the throttle stop screw to raise idle speed.

Do instead Leave the stop alone and set idle with the idle control system; the stop defines the closed reference that idle and decel logic depend on.Medium18

Myths vs facts

Myth The TPS tells the ECU how much air the engine is getting.

Fact It only reports throttle angle. Airflow at a given angle varies with engine speed, manifold pressure and air density, which is why most ECUs use MAP or MAF for load and TPS for transient detection.12

Myth Any TPS will work if the plug fits.

Fact Sensors differ in resistance, travel, direction and, on drive-by-wire bodies, in the second-track characteristic. The ECU calibration must match, and electronic throttles need both tracks wired correctly for their safety checks.Medium47

Myth A small TPS dead spot does not matter.

Fact A worn spot in a potentiometer track makes the signal drop out at one angle. The ECU can read that as a sudden throttle change, causing stumbles from false acceleration enrichment or, on electronic throttles, a plausibility fault.Medium57

Frequently asked

What does a throttle position sensor do?

It tells the ECU how far the throttle is open and how fast it is moving. The ECU uses that to detect idle, add fuel when the throttle opens quickly, estimate load on alpha-N systems, enable full-load tables and, on electronic throttles, confirm the plate is where it was commanded.31

How do you test a throttle position sensor?

Key on, engine off, check for about 5 V between the reference and sensor ground. Then measure the signal while slowly opening the throttle: it should rise smoothly with no jumps or dropouts. A scope or fast log catches dead spots a multimeter misses. On drive-by-wire, log both tracks together.Medium451

What voltage should a TPS read at idle?

It depends on the sensor, so compare with the learned closed value rather than a generic number. Most sensors sit somewhat above 0 V at closed throttle so the ECU can detect a short. On Bosch's electronic throttle body, one track starts near 0 V and the other near 5 V.Medium43

What are the symptoms of a bad throttle position sensor?

Common signs are hesitation at one throttle angle, unstable or high idle, surging at light cruise, erratic automatic shifts and trouble codes. On electronic throttles, a disagreement between the two tracks usually triggers a reduced-power limp mode with a warning light.Medium3710

Can you drive with a bad throttle position sensor?

Briefly and carefully, at most. A cable-throttle car may run poorly but still respond to the pedal. A drive-by-wire car usually drops into limp mode with the throttle held near its default, giving little power, which can be unsafe in traffic. Fix the fault before driving normally.Medium74

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

10 sources
  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  3. Throttle position sensor · Wikipedia · reference · retrieved 2026-10-27
  4. Electronic Throttle Body data sheet 68749835 · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  5. Potentiometer · Wikipedia · reference · retrieved 2026-10-27
  6. Hall effect sensor · Wikipedia · reference · retrieved 2026-10-27
  7. Electronic throttle control · Wikipedia · reference · retrieved 2026-10-27
  8. Idle air control actuator · Wikipedia · reference · retrieved 2026-10-27
  9. TPS7B69xx-Q1 high-voltage ultra-low IQ low-dropout regulator data sheet · Texas Instruments · vendor-doc · retrieved 2026-10-27
  10. Saab 9-3 (1999) Trionic T7: DTC P1230 Throttle Position Sensor 1 and 2 Circuit, Sum Out of Range · Saab Workshop Information System (saabwisonline.com mirror) · service-manual · retrieved 2026-10-27