Accelerator pedal position sensor (APPS)

APPSAPP sensorpedal position sensorPPSaccelerator pedal modulethrottle pedal sensor

An accelerator pedal position sensor is the sensor in a drive-by-wire pedal that converts pedal travel into electrical signals for the ECU. It provides two independent outputs with different characteristics so the ECU can cross-check them, detect faults and set a safe throttle position if they disagree.123

How it works

With electronic throttle control there is no cable from pedal to throttle.

The pedal sensor expresses driver demand, and the ECU decides throttle angle, which lets it add idle control, traction control, torque limits and cruise control.23

Redundancy is the core feature. CTS's Series 552 pedal assembly uses a contacting sensor with dual outputs. In its data sheet, the second signal is set at half the first at idle, 15% and 7.5% of supply, and the two are checked for correlation as SIG1 minus twice SIG2.1

Some pedals use potentiometer tracks, while others use non-contact Hall or inductive sensing to avoid track wear. Either way, each output usually has its own supply and ground so that a single wiring fault cannot corrupt both signals in the same way.Medium143

In tuning

Pedal position is a request, not a throttle angle.

The calibration maps pedal percentage to throttle angle or to a torque request, and that map shapes how the car feels. A progressive map softens the first part of pedal travel; it does not change maximum airflow.Medium23

When fitting a pedal from another vehicle, match both tracks' ranges and slopes in the ECU and test each fault response: unplug one track, short one to ground, and confirm the throttle drops to its safe default before driving.Medium12

Myths vs facts

Myth The two pedal signals are just a spare in case one fails.

Fact They are compared continuously. The ECU checks that each is in range and that they agree within a tolerance. A mismatch is treated as a fault, and the throttle moves to a reduced-power or idle position.21

Myth A pedal-to-throttle map that reaches 100% early makes more power.

Fact It only changes response to pedal travel. Full throttle is still full throttle. An aggressive map can make low-speed driving and traction harder to manage.Medium23

Frequently asked

What does an accelerator pedal position sensor do?

It turns pedal travel into electrical signals that tell the ECU how much power the driver wants. In a drive-by-wire system the ECU then sets the throttle angle, which lets it blend in idle control, traction control, cruise control and torque limits.23

Why does a pedal sensor have two signals?

For safety. The ECU compares two independent signals and treats any disagreement as a fault. CTS's Series 552 pedal, for example, outputs one signal at 15% and the other at 7.5% of supply at idle, so a short between them or to a rail shows up as a correlation error.12

Can I use any pedal with drive by wire?

Only if the ECU can be calibrated to its two signals and its fault checks. Pedals differ in output ranges, slopes, whether the second track is half-scale or inverted, and connector pinout. Confirm each fault response on the bench before the car is driven.Medium12

What are the symptoms of a bad accelerator pedal position sensor?

Typical signs are sudden reduced-power mode, the throttle not responding to part of the pedal travel, high idle, or trouble codes for pedal sensor correlation or range. Because a fault defaults the throttle toward closed, symptoms usually show as loss of power rather than unintended acceleration.Medium23

Wiring, pinouts and parts

Used in these guides

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Accelerator Pedals Series 552 data sheet · CTS Corporation · vendor-doc · retrieved 2026-10-27
  2. Electronic throttle control · Wikipedia · reference · retrieved 2026-10-27
  3. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  4. Hall effect sensor · Wikipedia · reference · retrieved 2026-10-27