Sensor type · Potentiometer 0-5 V · Hall effect (digital)

Accelerator pedal position sensor

APPAPPSpedal sensoraccelerator pedal module

An accelerator pedal position (APP) sensor turns pedal travel into two independent signals so a drive-by-wire ECU can open the throttle and cross-check the request. Each track needs its own 5 V reference and ground, which is why most pedal modules have six wires. The ECU compares the tracks and limits throttle when they disagree.Medium1

Parts in the library

Support across ECUs

Across the 3 parts in this hub (0 with a maker-verified pinout). Open a part for the setup notes and sources.

GAINS ECU23 configurable (generic input)
Haltech (Elite / Nexus)3 unverified
Link (G4X)3 unverified
MoTeC (M1)3 unverified
ECUMaster (EMU Black)3 unverified
AEM (Infinity)3 unverified
MaxxECU3 unverified
Holley (Terminator X / EFI)3 unverified

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

How it works

Pedal modules use two potentiometer tracks or two contactless Hall elements. The second track often runs at a different slope or offset, so a short between the two tracks is detectable.Medium1

The ECU turns pedal position into a throttle-angle target and drives the throttle motor until the throttle sensors agree with that target.Medium1

Types and variants

Dual potentiometerPotentiometer 0-5 V

Two resistive tracks on the pedal shaft; analog 0-5 V outputs.Medium1

Dual HallHall effect (digital)

Two contactless Hall outputs, still analog 0-5 V levels; no wiper wear.Medium1

Wiring

Keep each pedal track's reference and ground separate where the module provides them, so one shorted circuit cannot take down both tracks.Medium1

Pedal tracks go straight to analog inputs on the ECU that controls the throttle, never through CAN or a second module.2

Connector and wiring library

Common faults and checks

Throttle reduced to limp mode under hard acceleration

Likely cause Pedal tracks disagree (connector corrosion or a worn track)

Check Log both pedal tracks while pressing slowly; the ratio between them should stay constant across travel.Medium1

No throttle response at all

Likely cause Lost 5 V reference to the pedal

Check Measure each reference at the pedal connector with key on.Medium1

Frequently asked

Why does a pedal sensor have two signals?

So the ECU can check one against the other. If a track fails or shorts, the two readings stop agreeing and the ECU limits the throttle instead of acting on a bad request.Medium1

How many wires does an accelerator pedal sensor have?

Usually six on a dual-track module: a 5 V reference, a ground and a signal for each track. Some modules share a supply, so confirm against the pedal maker's pinout before wiring.Medium1

Can a pedal sensor share a reference with the throttle body?

Electrically it often works, but a short on one sensor then drags down every sensor on that reference. Use separate references where the ECU offers them.Low1

Related

Use it with GAINS

Accelerator pedal position sensor on GAINS hardware

ECU2AVI3-AVI4 (drive-by-wire APP1/APP2)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Pedal tracks for drive-by-wire. DBW sensors are allowed only on AVI1-6, never on a flex pin or CAN.Medium2

Analog inputs AVI1-6 take 0-5 V sensors, thermistors or switches, each with a switchable pull-up. Sensor 5 V is pin 28 (250 mA shared) and sensor ground is pin 29.2

GAINS hardware is pre-release concept design. Pin numbers come from the ECU2 v0.3 pin map and the PDM2 specification and can change before release; none of it has been tested on a vehicle yet.23

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  3. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)

Not yet indexed: fewer than 4 FAQs.